Loading ...
Sorry, an error occurred while loading the content.

Re: [Electronics_101] Re: old ammeter

Expand Messages
  • james nicholson
    Ok .I ll let you know when I get to it. Thank you ________________________________ From: Rick Sparber To: Electronics_101@yahoogroups.com
    Message 1 of 51 , Feb 14, 2013
    • 0 Attachment
      Ok .I'll let you know when I get to it. Thank you



      ________________________________
      From: Rick Sparber <rgsparber@...>
      To: Electronics_101@yahoogroups.com
      Sent: Thursday, February 14, 2013 1:51 PM
      Subject: RE: [Electronics_101] Re: old ammeter


       
      Start with a low resistance so the voltage across the meter movement is too small but safe. Then slowly raise the resistance.

      Rick

      -----Original Message-----
      From: Electronics_101@yahoogroups.com [mailto:Electronics_101@yahoogroups.com] On Behalf Of james nicholson
      Sent: Thursday, February 14, 2013 11:50 AM
      To: Electronics_101@yahoogroups.com
      Subject: Re: [Electronics_101] Re: old ammeter

      That's what I meant when I said that. I intended to start with a higher resistance and keep checking?

      ________________________________
      From: Rick Sparber rgsparber@...>
      To: Electronics_101@yahoogroups.com
      Sent: Thursday, February 14, 2013 1:25 PM
      Subject: RE: [Electronics_101] Re: old ammeter


      Just be careful not to blow the meter movement. I suggest you work UP and now down ;-)

      Rick

      -----Original Message-----
      From: Electronics_101@yahoogroups.com [mailto:Electronics_101@yahoogroups.com] On Behalf Of james nicholson
      Sent: Wednesday, February 13, 2013 1:07 PM
      To: Electronics_101@yahoogroups.com
      Subject: Re: [Electronics_101] Re: old ammeter

      Rick,
      I have some heating element wire from an old dehumidifier that was also a heater. Possibly I will start big and work my way down till it matches my Fluke meter reading. I am a retired mechanic from a Caterpillar dealership. Worked a lot on 12 & 24 volt heavy equipment systems but not so much on electronics. Thank you , James

      ________________________________
      From: Rick Sparber rgsparber@...>
      To: Electronics_101@yahoogroups.com
      Sent: Wednesday, February 13, 2013 8:26 AM
      Subject: RE: [Electronics_101] Re: old ammeter

      I make my low resistance shunts out of thin steel wire although heating
      element wire can be used too. The trick is to accurately measure it.

      Rick

      -----Original Message-----
      From: Electronics_101@yahoogroups.com
      [mailto:Electronics_101@yahoogroups.com] On Behalf Of Kerim F
      Sent: Wednesday, February 13, 2013 6:13 AM
      To: Electronics_101@yahoogroups.com
      Subject: [Electronics_101] Re: old ammeter

      --- In Electronics_101@yahoogroups.com, "Nick" wrote:
      >
      > Hi guys, I'm fairly new to electronics and have a question about an old
      ammeter that I acquired. I know that it requires a shunt as the wires on the
      posts are small and it is a 100 amp meter. In the lower right corner of the
      meter face it shows [E.S.=50mv ]. What can I use for a shunt and does it go
      in series with the + or in parallel with the + and -. Will it read full
      scale with the shunt installed [not that I would ever need that much]. Thank
      you in advance for any info.
      >

      In parallel.
      An ammeter is actually a sensitive voltmeter.
      It seems the full scale voltage of your ammeter is 50mV.
      If the the shunt is 1 Ohm, the full sacle current would be 50mA If the the
      shunt is 0.1 Ohm, the full sacle current would be 500mA.
      If the the shunt is 0.01 Ohm, the full sacle current would be 5A.
      If the the shunt is ?? Ohm, the full sacle current would be 100A ;)

      ------------------------------------

      Please trim excess when replyingYahoo! Groups Links

      [Non-text portions of this message have been removed]

      ------------------------------------

      Please trim excess when replyingYahoo! Groups Links

      [Non-text portions of this message have been removed]

      ------------------------------------

      Please trim excess when replyingYahoo! Groups Links




      [Non-text portions of this message have been removed]
    • Rick Sparber
      In reading the thread, it sounds like you got the help you needed. Rick ... From: Electronics_101@yahoogroups.com [mailto:Electronics_101@yahoogroups.com] On
      Message 51 of 51 , Mar 21 7:18 AM
      • 0 Attachment
        In reading the thread, it sounds like you got the help you needed.

        Rick

        -----Original Message-----
        From: Electronics_101@yahoogroups.com [mailto:Electronics_101@yahoogroups.com] On Behalf Of james nicholson
        Sent: Wednesday, March 20, 2013 1:45 PM
        To: Electronics_101@yahoogroups.com
        Subject: Re: [Electronics_101] Re: old ammeter

        Hi Rick,
        I have another question for you. The control board on our treadmill went out. I have done some tests and the motor is fine. It's a DC 120 volt brush type motor, it has a choke coil in series with the motor. I don't want to spend $120 for a new board unless I have too [ retired & fixed income].I ran the motor with a big ceramic ohmite pot of 68 ohms and then thru a bridge rectifier. The motor ran fine and I could control the speed but the pot got really hot which is understandable because of the iron coil. I found a router speed control on ebay that is good for 120 volt-15 amp--says it is good for any ac or dc motor brush type. What are your thoughts on using this as a speed control. Sent a pic of the motor data plate. Any help would be greatly appreciated Just remember I'm very elementary when it comes to electronics. By the way haven't got to my ammeter shunt yet but will get it.
        Thank you, James
      Your message has been successfully submitted and would be delivered to recipients shortly.