Re: [Electronics_101] Re: Need to know what something is called or recomendations...
- On Sat, 01 Apr 2006 19:54:51 +0200, lcdpublishing
> My concern is with the home-made PCBs and the durability of theYou'd really need to plate those anyway...
> copper that would go into the sockets. So much of my stuff is all
> trial and error (because I don't know much - yet), that I would
> worry I would wear the copper off the PCB.
- On Saturday 01 April 2006 12:49 pm, Stefan Trethan wrote:
> On Sat, 01 Apr 2006 19:33:07 +0200, Roy J. TellasonYes.
> <rtellason@...> wrote:
> > I know that card-edge connectors used to be used a whole lot more than
> > they seem to be now -- like for floppy drivers, ferinstance, when 5.25"
> > drives were the common thing. And that they've moved to pin-type
> > connectors instead. This has to tell us something, perhaps about
> > reliability?
> Perhaps also about pin density i think not all of those came at 100mil
> I wouldn't say they are by design unreliable, since all the "important"I did that quite often as a part of the repair process. In the case of the
> features (plated contact areas and spring loaded contacts) can be there,
> but it seems cleaning them quite often fixes a contact problem.
Osborne 1 it sometimes also took building up solder on the board, because
they chose for some reason to make a custom board to have on the drive and to
run power through the ribbon cable, which created reliability problems.
> They are also used a lot in all kinds of test equipment (e.g. tek scopesAgreed.
> with plugins). You can clean the female side by folding a piece of paper
> over a piece of PCB and wetting it with alcohol before inserting it several
> times. I wouldn't prefer to use them for anything, esp. since it would
> require me to set up for plating the female side, which i don't want to do,
> or i would need to buy the female connectors, which eliminated the price
Member of the toughest, meanest, deadliest, most unrelenting -- and
ablest -- form of life in this section of space, a critter that can
be killed but can't be tamed. --Robert A. Heinlein, "The Puppet Masters"
Information is more dangerous than cannon to a society ruled by lies. --James
- They actually ship from Thailand, although the contact point is in Sydney.
I've used them several times over the years and have been very happy with
the service. One recent order was short-supplied, seemingly due to confusion
bewtween english and thai, but an e-mail to the company brought the missing
chips within a few days.
----- Original Message -----
From: "lcdpublishing" <lcdpublishing@...>
Sent: Saturday, April 01, 2006 10:44 PM
Subject: [Electronics_101] Re: Need to know what something is called or
> WOW, those are much cheaper there than even at Jameco. I think I
> will order from them - I don't need them right away so the extra
> shipping time isn't bad. Well, in reality when I order from Jameco,
> it usually takes a week for me to get the stuff anyway, so this
> would end up being about the same ship time.
> Very cool, thanks for the lead!
> --- In Electronics_101@yahoogroups.com, "Randy Ledyard"
> <rll_groups@...> wrote:
>> Before you plunk your money down at Digikey, check these guys out
>> They ship from Australia, so it's 7-10 days to get your shipment,
> but if you
>> don't mind the wait, the prices are a lot better.
>> Also, you might want to look at the IDC connectors.
>> Based on the calculations I did, if you can get your cables for
> free (old
>> HDD and FDD cables), the IDC conns were the cheapest point to point
>> connectors, esp in the 8-12 conductor range. Plus you have the
>> flexibility in connection that a hard connector won't tolerate,
> and they are
>> polarized, to prevent hookup goofs. You can crimp them with an
>> bench vise.
>> > -----Original Message-----
>> > From: Electronics_101@yahoogroups.com
>> > [mailto:Electronics_101@yahoogroups.com]On Behalf Of
>> > Sent: Friday, March 31, 2006 10:59 AM
>> > To: Electronics_101@yahoogroups.com
>> > Subject: [Electronics_101] Re: Need to know what something is
> called or
>> > recomendations...
>> > Thanks guys!
>> > Yes, those at Digikey and the ones Robert showed are what I am
>> > for. That should do the trick for what I need to do. It seems
>> > though I am having more and more needs to stack boards like this
> so I
>> > am going to have to get a variety of them.
>> > Chris
> Yahoo! Groups Links