Loading ...
Sorry, an error occurred while loading the content.

Re: [Easy400Group] AS400 consol??

Expand Messages
  • HarryWilliams
    I am by no means an expert, but to connect you are using the console lan adapter. You must dedicate one port on the iseries to be the lan adapter. Signon to
    Message 1 of 5 , Mar 18, 2013
    • 0 Attachment
      I am by no means an expert, but to connect you are using the console lan adapter.

      You must dedicate one port on the iseries to be the lan adapter. 


      Signon to SST.   STRSST

      Once signed on,  tale an option

      8. Work with service tools user IDs and Devices
      Then
      4. Configure service tools LAN adapter

      Internet address  . . . . . .   10.14.51.10                            
      Gateway router address  . . .   10.14.51.2                             
      Subnet mask . . . . . . . . .   255.255.255.0                          
      Host name for service tools .   AHOSTNAME                           
      Node  . . . . . . . . . . . .   000000000000    (0 is default)         
      Duplex  . . . . . . . . . . .   AUTO            HALF, FULL, AUTO       
      Network speed . . . . . . . .   AUTO            4, 10, 16, 100, AUTO   
                                                                             
      Ethernet standard . . . . . .   ETHV2           ETHV2       

      You will need to activate the IP address
      F14=Activate



      I used the gateway address as the address on the PC.  10.14.51.2 

         Now the console lan adaper would respond.    This is on a 720 which did not have a twinax device. 

      But option 3 from Work with service tools user IDs and Devices

               Select one of the following:                                 
        Console type . . . . . . . . . . . . . . . .  3            
           1. Twinaxial                                            
           2. Operations console(Direct)                           
           3. Operations console(LAN)                              
           4. Hardware management console(HMC)                     
      Current state of console tag   . . . . . . . .  0            

      You can change this to 3. 


      Now,  be cautious,  this has caused me some grief.   As I got our system changed to HMC,  then the iseries could not find the load sources.  It took a slip (restore) install to find the information on the disk.  (I had to reload the PTF's).   I never lost any information,   but I had to go though several IBM'ers before I got an answer.   Just be cautious. 







      On 3/18/2013 1:53 PM, gkh wrote:  

      I know this isn't really a CGIDEV2 issue- but I am trying to set up an windows XP machine (using IBM client aceess console) to be a console for my company's AS400 & am entirely unable to figure out why it doesn't work.  Our AS400 is on OS v5r4, my client access is 6.1.  I don't know how to check to see which AS400 we physically have. I already have:
      1. Loaded client access
      2. Set up the iseries "modem"
      3. checked for conflicts on the XP machine
      4. tried this with both a standard rs232 cable AND a null modem cable (since I couldn't find anything that specified which was needed on the IBM site)

      did I miss any steps?!


    • Jean-Marc Gigandet
      Hi Console with an rs-232 cable ? :-O I ve never heard of a console working on this. On Lan, on Twinax if available, but on rs-232... Are you trying to connect
      Message 2 of 5 , Mar 18, 2013
      • 0 Attachment
        Hi

        Console with an rs-232 cable ? :-O
        I've never heard of a console working on this. On Lan, on Twinax if available, but on rs-232...
        Are you trying to connect remotely ? Is this really a console you want or a simple terminal display ?

        Regards,
        Jean-Marc

        Le 18/03/2013 19:53, gkh a écrit :
         

        I know this isn't really a CGIDEV2 issue- but I am trying to set up an windows XP machine (using IBM client aceess console) to be a console for my company's AS400 & am entirely unable to figure out why it doesn't work.  Our AS400 is on OS v5r4, my client access is 6.1.  I don't know how to check to see which AS400 we physically have. I already have:
        1. Loaded client access
        2. Set up the iseries "modem"
        3. checked for conflicts on the XP machine
        4. tried this with both a standard rs232 cable AND a null modem cable (since I couldn't find anything that specified which was needed on the IBM site)

        did I miss any steps?!


      • Bob Cagle
        You may get more assistance by posting your question to the Midrange board over on www.Midrange.com. Hope this helps. Bob Cagle IT Manager Lynk, Inc. From:
        Message 3 of 5 , Mar 19, 2013
        • 0 Attachment

          You may get more assistance by posting your question to the Midrange board over on www.Midrange.com.

           

          Hope this helps.

           

          Bob Cagle

          IT Manager

          Lynk, Inc.

           

          From: Easy400Group@yahoogroups.com [mailto:Easy400Group@yahoogroups.com] On Behalf Of gkh
          Sent: Monday, March 18, 2013 1:54 PM
          To: Easy400Group@yahoogroups.com
          Subject: [Easy400Group] AS400 consol??

           

           

          I know this isn't really a CGIDEV2 issue- but I am trying to set up an windows XP machine (using IBM client aceess console) to be a console for my company's AS400 & am entirely unable to figure out why it doesn't work.  Our AS400 is on OS v5r4, my client access is 6.1.  I don't know how to check to see which AS400 we physically have. I already have:
          1. Loaded client access
          2. Set up the iseries "modem"
          3. checked for conflicts on the XP machine
          4. tried this with both a standard rs232 cable AND a null modem cable (since I couldn't find anything that specified which was needed on the IBM site)

          did I miss any steps?!

        • gkh
          Thank you! Now I at least have a direction to start in :)
          Message 4 of 5 , Mar 20, 2013
          • 0 Attachment
            Thank you! Now I at least have a direction to start in :)

            On Mon, Mar 18, 2013 at 8:00 PM, HarryWilliams <harry@...> wrote:
             

            I am by no means an expert, but to connect you are using the console lan adapter.

            You must dedicate one port on the iseries to be the lan adapter. 


            Signon to SST.   STRSST

            Once signed on,  tale an option

            8. Work with service tools user IDs and Devices
            Then
            4. Configure service tools LAN adapter

            Internet address  . . . . . .   10.14.51.10                            
            Gateway router address  . . .   10.14.51.2                             
            Subnet mask . . . . . . . . .   255.255.255.0                          
            Host name for service tools .   AHOSTNAME                           
            Node  . . . . . . . . . . . .   000000000000    (0 is default)         
            Duplex  . . . . . . . . . . .   AUTO            HALF, FULL, AUTO       
            Network speed . . . . . . . .   AUTO            4, 10, 16, 100, AUTO   
                                                                                   
            Ethernet standard . . . . . .   ETHV2           ETHV2       

            You will need to activate the IP address

            F14=Activate



            I used the gateway address as the address on the PC.  10.14.51.2 

               Now the console lan adaper would respond.    This is on a 720 which did not have a twinax device. 

            But option 3 from Work with service tools user IDs and Devices

                     Select one of the following:                                 
              Console type . . . . . . . . . . . . . . . .  3            
                 1. Twinaxial                                            
                 2. Operations console(Direct)                           
                 3. Operations console(LAN)                              
                 4. Hardware management console(HMC)                     
            Current state of console tag   . . . . . . . .  0            

            You can change this to 3. 


            Now,  be cautious,  this has caused me some grief.   As I got our system changed to HMC,  then the iseries could not find the load sources.  It took a slip (restore) install to find the information on the disk.  (I had to reload the PTF's).   I never lost any information,   but I had to go though several IBM'ers before I got an answer.   Just be cautious. 







            On 3/18/2013 1:53 PM, gkh wrote:
             

            I know this isn't really a CGIDEV2 issue- but I am trying to set up an windows XP machine (using IBM client aceess console) to be a console for my company's AS400 & am entirely unable to figure out why it doesn't work.  Our AS400 is on OS v5r4, my client access is 6.1.  I don't know how to check to see which AS400 we physically have. I already have:
            1. Loaded client access
            2. Set up the iseries "modem"
            3. checked for conflicts on the XP machine
            4. tried this with both a standard rs232 cable AND a null modem cable (since I couldn't find anything that specified which was needed on the IBM site)

            did I miss any steps?!



          Your message has been successfully submitted and would be delivered to recipients shortly.