Loading ...
Sorry, an error occurred while loading the content.

Re: [Distillers] Liebig Condenser

Expand Messages
  • Bryan Bornais
    You want the cooling water to be counter flow to the vapour stream. You are right.   Cheers, Bryan ________________________________ From: eyendall
    Message 1 of 7 , Sep 29, 2011
    • 0 Attachment
      You want the cooling water to be counter flow to the vapour stream. You are right.
       
      Cheers,

      Bryan

      From: eyendall <eric_yendall@...>
      To: Distillers@yahoogroups.com
      Sent: Thursday, September 29, 2011 10:04:56 AM
      Subject: [Distillers] Liebig Condenser

       
      For a Liebig condensor coming off a reflux still, should the cold water be introduced at the top or the bottom? I have been putting the cold water through the bottom but have just come across a Liebig diagram indicating the reverse. Does it make any difference? Thanks.



    • Max Norton
      Cold water should come in at the bottom. As the coil heats up the water, it rises to the top and is also pushed up by incoming cool water. The warm water is
      Message 2 of 7 , Sep 30, 2011
      • 0 Attachment
        Cold water should come in at the bottom. As the coil heats up the water, it rises to the top and is also pushed up by incoming cool water. The warm water is then drained off by the over flow. Thus you are continuously replacing warm water with cold water.
      • Thursty2
        ... Hi Max and fellow enthusiasts, Interesting discussion. With all due respects, the same would occur if the cold water were to enter at the other end. Water
        Message 3 of 7 , Sep 30, 2011
        • 0 Attachment
          --- In Distillers@yahoogroups.com, Max Norton <nortonshog@...> wrote:
          >
          > Cold water should come in at the bottom. As the coil heats up the water, it rises to the top and is also pushed up by incoming cool water. The warm water is then drained off by the over flow. Thus you are continuously replacing warm water with cold water.
          >
          Hi Max and fellow enthusiasts,

          Interesting discussion.

          With all due respects, the same would occur if the cold water were to enter at the other end.

          Water under pressure absorbs more heat before it boils - conversely less water is required to cause the same amount of cooling.

          So, in a free flowing condenser such as is used in the Nixon - Stone Reflux Still, the coil is the longest route to its bottom end, holding, at any given moment, the major volume (and weight) of all the water in the condenser. The straight (upstand?) part holds the minor (lighter) volume.

          As I see it, cold water entering the coil at the top, would cause some (albeit very minor) pressure because of the volume (and thus weight), and the propensity for the heated water to want to rise - to push back up the coil against the cold water entering.

          Therefore I believe it is more effective to have cold water entering at the coil and the heated water exiting up the straight part from the bottom.

          Not to be confused with a pressurised closed system such as that in a motor vehicle.
        • Harry
          I hate to burst your bubble Thursty. but there s a lot more to these heat exchangers (condensers) than mere reasoning . For instance, your idea of water
          Message 4 of 7 , Oct 1, 2011
          • 0 Attachment
            I hate to burst your bubble Thursty. but there's a lot more to these heat exchangers (condensers) than mere 'reasoning'.
            For instance, your idea of water entering the top and exiting the bottom, doesn't take into account the constant separation of dissolved gases in the coolant feed. Bubbles form in the upper regions of the coil right where you want to feed the coolant. Ergo, coolant flow is disrupted, there's gas in the coil and the heat exchanger either works very poorly or ceases functioning altogether (not good with ethanol involved). Think 'vapor lock' in your old time carburetted fuel line. Same thing. There's lots of other 'ifs' involved too. Suggest you research heat exchangers. Start at my Library; Engineering section...
            Free to read online. Link in sigline.


            Slainte!
            regards Harry
            http://distillers.tastylime.net
            =======================================

            --- In Distillers@yahoogroups.com, "Thursty2" <thursty2@...> wrote:
            >
            >
            >
            >
            >
            >
            > --- In Distillers@yahoogroups.com, Max Norton <nortonshog@> wrote:
            > >
            > > Cold water should come in at the bottom. As the coil heats up the water, it rises to the top and is also pushed up by incoming cool water. The warm water is then drained off by the over flow. Thus you are continuously replacing warm water with cold water.
            > >
            > Hi Max and fellow enthusiasts,
            >
            > Interesting discussion.
            >
            > With all due respects, the same would occur if the cold water were to enter at the other end.
            >
            > Water under pressure absorbs more heat before it boils - conversely less water is required to cause the same amount of cooling.
            >
            > So, in a free flowing condenser such as is used in the Nixon - Stone Reflux Still, the coil is the longest route to its bottom end, holding, at any given moment, the major volume (and weight) of all the water in the condenser. The straight (upstand?) part holds the minor (lighter) volume.
            >
            > As I see it, cold water entering the coil at the top, would cause some (albeit very minor) pressure because of the volume (and thus weight), and the propensity for the heated water to want to rise - to push back up the coil against the cold water entering.
            >
            > Therefore I believe it is more effective to have cold water entering at the coil and the heated water exiting up the straight part from the bottom.
            >
            > Not to be confused with a pressurised closed system such as that in a motor vehicle.
            >
          • KM Services
            Here is a thread on my liebig posted on New Distillers which could be of help.this condenser works very well.. http://tinyurl.com/43l856o Ken Mc (This is my
            Message 5 of 7 , Oct 1, 2011
            • 0 Attachment

              Here is a thread on my liebig posted on New Distillers which could be of help…this condenser works very well…. http://tinyurl.com/43l856o

               

               

               

              Ken Mc (This is my opinion and if I am wrong I will be corrected I am sure)

               


              From: Distillers@yahoogroups.com [mailto:Distillers@yahoogroups.com] On Behalf Of Harry
              Sent: Saturday, 1 October 2011 10:19 p.m.
              To: Distillers@yahoogroups.com
              Subject: [Distillers] Re: Liebig Condenser

               

               

              I hate to burst your bubble Thursty. but there's a lot more to these heat exchangers (condensers) than mere 'reasoning'.
              For instance, your idea of water entering the top and exiting the bottom, doesn't take into account the constant separation of dissolved gases in the coolant feed. Bubbles form in the upper regions of the coil right where you want to feed the coolant. Ergo, coolant flow is disrupted, there's gas in the coil and the heat exchanger either works very poorly or ceases functioning altogether (not good with ethanol involved). Think 'vapor lock' in your old time carburetted fuel line. Same thing. There's lots of other 'ifs' involved too. Suggest you research heat exchangers. Start at my Library; Engineering section...
              Free to read online. Link in sigline.

              Slainte!
              regards Harry
              http://distillers.tastylime.net
              =======================================

              --- In Distillers@yahoogroups.com, "Thursty2" <thursty2@...> wrote:

              >
              >
              >
              >
              >
              >
              > --- In Distillers@yahoogroups.com,
              Max Norton <nortonshog@> wrote:
              > >
              > > Cold water should come in at the bottom. As the coil heats up the
              water, it rises to the top and is also pushed up by incoming cool water. The warm water is then drained off by the over flow. Thus you are continuously replacing warm water with cold water.
              > >
              > Hi Max and fellow enthusiasts,
              >
              > Interesting discussion.
              >
              > With all due respects, the same would occur if the cold water were to
              enter at the other end.
              >
              > Water under pressure absorbs more heat before it boils - conversely less
              water is required to cause the same amount of cooling.
              >
              > So, in a free flowing condenser such as is used in the Nixon - Stone
              Reflux Still, the coil is the longest route to its bottom end, holding, at any given moment, the major volume (and weight) of all the water in the condenser. The straight (upstand?) part holds the minor (lighter) volume.
              >
              > As I see it, cold water entering the coil at the top, would cause some
              (albeit very minor) pressure because of the volume (and thus weight), and the propensity for the heated water to want to rise - to push back up the coil against the cold water entering.
              >
              > Therefore I believe it is more effective to have cold water entering at
              the coil and the heated water exiting up the straight part from the bottom.
              >
              > Not to be confused with a pressurised closed system such as that in a
              motor vehicle.
              >

            Your message has been successfully submitted and would be delivered to recipients shortly.