Loading ...
Sorry, an error occurred while loading the content.

Messages List

202543

Re: PR3 not working with Windows 10

Glen.. Go into the device manager and delete the hardware entry for the PR3 and start over following the Win 8.1 install process from Digitrax. And hope Marc
marcfournier95
3:27 AM
#202543
 
202542

Re: FW: [Digitrax] Re: Problem at club

No Marc is not incorrect and you got the DigiGroupSetup part wrong. Oh fart ! The Guru goofed. You must have a PR3 to do the updates... In a pinch you can
marcfournier95
3:19 AM
#202542
 
202541

Re: any ideas before i ship Zephyr DCS50 for repair

So you tried both the OPSW 36 and OPSW 39 reset and this did not correct the issue ? and you tried this more than once ? NO decoder selected, the brake led
marcfournier95
3:17 AM
#202541
 
202540

Re: any ideas before i ship Zephyr DCS50 for repair

To: Steve ‘Deep Six’ a DCS50. Why would you do such a thing? I cannot understand why you would not send the DCS50 to Digitrax for repair. The
Bob Young
12:31 PM
#202540
 
202539

Re: Problem at club

Pat, why would one operate on track that is "beyond filthy" and expect no problems? I bet even you "other never-fail system" would balk at this situation.
asychis
11:53 AM
#202539
 
202538

any ideas before i ship Zephyr DCS50 for repair

Guys i was going to deep six this unit but am attached to it.Its an extra unit i have just because. I use it for a reverser and a booster sometimes.Anyways
cncpgr
11:45 AM
#202538
 
202537

FW: [Digitrax] Re: Problem at club

Hi Folks: Ross Kudlick contacted me off list to remind me that JMRI has its own version of DigiGroupSetup, which works with a LocoBuffer. Have used it and it
John M Wallis
11:23 AM
#202537
 
202536

Re: PR3 not working with Windows 10

Marc, The Win10 device manager sees the PR3 as an incorrectly installed device with the yellow triangle. Shows up under USB devices with the entry = Unknown
gtittermary
4:51 AM
#202536
 
202535

Re: PR3 not working with Windows 10

I did not say that I upgraded my old win7 railroad PC. It was x64 and had a thermal failure due to a bad CPU Fan. The upgrade was to an x64 win7 Dell office
John McMasters
Aug 3
#202535
 
202534

Re: Problem at club

Hi Folks: Marc is incorrect in his statement that you must have a PR3 to do the upgrade. This and all non-sound upgrades using DigiIPL from the Digitrax site
John M Wallis
Aug 3
#202534
 
202533

Re: Problem at club

He responded that there was no battery involved in all this as he was / is tethered only. He does not use wireless or battery as they encounter communication
marcfournier95
Aug 3
#202533
 
202532

Re: Problem at club

I'd also look at the throttle, beyond the fact that it is not up to date. I have two DT402Ds, one of which will run fine with the a battery that is down to
Mick Moignard
Aug 3
#202532
 
202531

Re: More Throttles

... Thanks for the help. I figured as much. I do run the JMRI (thanks Ken!) and use my phone for a throttle. I sometimes just like the feel of turning a knob
marcfournier95
Aug 2
#202531
 
202530

Re: PR3 not working with Windows 10

" USB serial driver (Usbser.sys) (Windows Drivers) https://msdn.microsoft.com/en-us/library/windows/hardware/dn707976%28v=vs.85%29.aspx USB serial driver
marcfournier95
Aug 2
#202530
 
202529

Re: PR3 will have an upgrade for Windows 10

If his was a clean, install from scratch, it is very surprising it would find the proper USBSER.SYS as the file is in a different folder all together and must
marcfournier95
Aug 2
#202529
 
View First Topic Go to View Last Topic
Loading 1 - 15 of total 202,543 messages