Loading ...
Sorry, an error occurred while loading the content.

Re: [DVRPTR_V1] AMBE-Addon Zero Series "special offer"

Expand Messages
  • Steffen Kaiser
    ... werden auch die Alten 1.er Boards diese Unterstützung haben ??? Ich habe DVRPTR und Ambe Board aus den Anfaengen! Gruss Steffen Am 09.05.2013 09:30,
    Message 1 of 7 , May 9, 2013
    • 0 Attachment
      Am 09.05.2013 09:30, schrieb do1fjn:

      In den folgenden Wochen werde ich die Entwicklung der Firmware in Angriff nehmen, damit die neuen Features wie Headset-Benutzung, die Lautstärke-Regelung über die Up/Down Tasten des Mikrofons oder das Senden von DTMF bei einem Yaesu MH-59 Mikrofon funktioniert.

      -

      werden auch die Alten  1.er Boards diese Unterstützung haben ???
      Ich habe DVRPTR und Ambe Board aus den Anfaengen!

      Gruss Steffen

    • do1fjn
      Hallo Steffen, ... Nein - dies ist technisch nicht möglich. Die erste Version des AMBE-Boards (von Stefan entwickelt) hat keine Modular-8 Buchse. Es sind 3
      Message 2 of 7 , May 9, 2013
      • 0 Attachment
        Hallo Steffen,


        --- In DVRPTR_V1@yahoogroups.com, Steffen Kaiser <dl5sfi@...> wrote:
        > werden auch die Alten 1.er Boards diese Unterstützung haben ???
        > Ich habe DVRPTR und Ambe Board aus den Anfaengen!

        Nein - dies ist technisch nicht möglich. Die erste Version des AMBE-Boards (von Stefan entwickelt) hat keine Modular-8 Buchse. Es sind 3 weitere Verbindungen (Up/Down/Fast) zwischen der Buchse und dem DV-RPTR nötig.
        Die Firmware wird ein MH-59 Mikro automatisch erkennen und natürlich weiterhin mit dem resten AMBE-Board zusammenarbeiten.

        ---

        > "Supports the new firmware a MH-59 microphone too?"
        < No - its not possible because it's need 3 additional connections between a Modular8p8c connector and the DV-RPTR. The first board contains two jacks for a handset-microphone...

        The new firmware itself will defect such a microphone automaticly and allow operation with the first AMBE board too.

        73,
        Jan
      • do1fjn
        Hi all, I the first DV-RPTR group I m still a moderated member, I posted this special offer too, but now - a day later - it s not approved by the
        Message 3 of 7 , May 10, 2013
        • 0 Attachment
          Hi all,

          I the first DV-RPTR group I'm still a "moderated" member, I posted this "special offer" too, but now - a day later - it's not approved by the group-owner...
          So I will continue my support for the DV-RPTR V1 hardware only in THIS group - simply because I can't answer quick in the other group...

          So for every question or request a user must decide with domain it is:

          DV-RPTR V1 hardware, opensource Firmware (V1.10e, V1.69b):
          THIS group, DO1FJN

          DV-RPTR V2 hardware:
          old DV-RPTR group, DG1HT

          Firmware (close source) and ControlCenter:
          old DV-RPTR group, DJ0ABR

          Jonathan's Repeater Software:
          "pcrepeatercontroller" Yahoo group

          Almost 100% of reflector / DCS problems caused on the PC site...

          I'm not happy about this splitting...


          73,
          Jan
        • Fred PA4YBR
          Jan, This is a normal decision. You cannot support everything in/on/connectedto the board, you just have to make choices. We did, too. I see nothing
          Message 4 of 7 , May 10, 2013
          • 0 Attachment
            Jan,
             
            This is a normal decision.  You cannot support "everything" in/on/connectedto the
            board, you just have to make choices.   We did, too.  I see nothing wrong with the
            "support rules" laid out in your note!
             
            --fred
             


            From: DVRPTR_V1@yahoogroups.com [mailto:DVRPTR_V1@yahoogroups.com] On Behalf Of do1fjn
            Sent: Friday, May 10, 2013 9:08 AM
            To: DVRPTR_V1@yahoogroups.com
            Subject: [DVRPTR_V1] Announcement personal note...

             

            Hi all,

            I the first DV-RPTR group I'm still a "moderated" member, I posted this "special offer" too, but now - a day later - it's not approved by the group-owner...
            So I will continue my support for the DV-RPTR V1 hardware only in THIS group - simply because I can't answer quick in the other group...

            So for every question or request a user must decide with domain it is:

            DV-RPTR V1 hardware, opensource Firmware (V1.10e, V1.69b):
            THIS group, DO1FJN

            DV-RPTR V2 hardware:
            old DV-RPTR group, DG1HT

            Firmware (close source) and ControlCenter:
            old DV-RPTR group, DJ0ABR

            Jonathan's Repeater Software:
            "pcrepeatercontroller" Yahoo group

            Almost 100% of reflector / DCS problems caused on the PC site...

            I'm not happy about this splitting...

            73,
            Jan

          Your message has been successfully submitted and would be delivered to recipients shortly.