Loading ...
Sorry, an error occurred while loading the content.

Re: [DVRPTR_V1] Re: AMBE-Addon

Expand Messages
  • Fran Miele
    rj45 --Fran,W1FJM IMPORTANT: The contents of this email and any attachments are confidential. They
    Message 1 of 10 , Dec 6, 2012
    • 0 Attachment
      rj45

      --Fran,W1FJM

       

       


      IMPORTANT: The contents of this email and any attachments are confidential. They are intended for the named recipient(s) only. If you have received this email by mistake, please notify the sender immediately and do not disclose the contents to anyone or make copies thereof.


      On Thu, Dec 6, 2012 at 10:28 AM, gautea <gautea@...> wrote:
       

      Hi Jan
      The Icom HM-118TN, cheap from 409Shop.com is working fine. RJ45, with DTMF gen. and 4x4 keyboard. Specified for nominal 8V supply though. Not sure if 5V is enough for the DTMF chip. A simple mod with LM7808 would fix problem with voltage. Has UP/DWN buttons, needs ADC single line input on the DVRPTR, nice for volume UP/DWN from the mic. No LS so separate audio jack is fine.
      regards
      Gaute LB6YD



      --- In DVRPTR_V1@yahoogroups.com, "do1fjn" <dvrptr@...> wrote:
      >
      > Hi,
      >
      > The original AMBE Addon board was designed and produced by Stefan (SR-Systems).
      > I see that there is some interests in it, so I decided to finish my sheet and layout for a compatible replacement.
      >
      > My previous device prototype 'DV-ATRX' uses a RJ45 8pin connector (standard 5V Yaesu pinning + rewiring facility).
      >
      > + Serial connection for keypads or displays
      > + or Up/Down/Fast key-inputs
      > - no low cost microphones
      > - only with external speaker (3.5mm jack)
      >
      > What is yours opinion? Which kind of microphone connector is the best?
      >
      > 73
      > Jan
      >



    • ct1jib
      Hi Jan I share the same opinion, RJ45. Jorge
      Message 2 of 10 , Dec 6, 2012
      • 0 Attachment
        Hi Jan

        I share the same opinion, RJ45.

        Jorge


        --- In DVRPTR_V1@yahoogroups.com, "do1fjn" <dvrptr@...> wrote:
        >
        > Hi,
        >
        > The original AMBE Addon board was designed and produced by Stefan (SR-Systems).
        > I see that there is some interests in it, so I decided to finish my sheet and layout for a compatible replacement.
        >
        > My previous device prototype 'DV-ATRX' uses a RJ45 8pin connector (standard 5V Yaesu pinning + rewiring facility).
        >
        > + Serial connection for keypads or displays
        > + or Up/Down/Fast key-inputs
        > - no low cost microphones
        > - only with external speaker (3.5mm jack)
        >
        > What is yours opinion? Which kind of microphone connector is the best?
        >
        > 73
        > Jan
        >
      • Jim
        Hi Regarding microphones,something to consider is the strain placed on the microphone/speaker sockets by plugging in the microphone/speaker itself. I d be
        Message 3 of 10 , Dec 6, 2012
        • 0 Attachment
          Hi

          Regarding microphones,something to consider is the strain placed on the
          microphone/speaker sockets by plugging in the microphone/speaker itself.
          I'd be tempted to used screened flying leads to the unit itself.

          Jim


          On 06/12/2012 14:43, do1fjn wrote:
          > Hi,
          >
          > The original AMBE Addon board was designed and produced by Stefan (SR-Systems).
          > I see that there is some interests in it, so I decided to finish my sheet and layout for a compatible replacement.
          >
          > My previous device prototype 'DV-ATRX' uses a RJ45 8pin connector (standard 5V Yaesu pinning + rewiring facility).
          >
          > + Serial connection for keypads or displays
          > + or Up/Down/Fast key-inputs
          > - no low cost microphones
          > - only with external speaker (3.5mm jack)
          >
          > What is yours opinion? Which kind of microphone connector is the best?
          >
          > 73
          > Jan
          >
          >
          >
          >
          > ------------------------------------
          >
          > Yahoo! Groups Links
          >
          >
          >
          >
        • vk7yxx
          I think I ll go against the trend and suggest keeping the Kenwood speaker/mic arrangement. It s convenient, compatible with existing AMBE boards, and has
          Message 4 of 10 , Dec 6, 2012
          • 0 Attachment
            I think I'll go against the trend and suggest keeping the Kenwood speaker/mic arrangement. It's convenient, compatible with existing AMBE boards, and has caused no issues for me. The last thing the compact DVRPTR needs is more cables hanging out of it.

            Would the RJ45 socket even fit in the standard DVRPTR V1 case?

            --- In DVRPTR_V1@yahoogroups.com, "do1fjn" <dvrptr@...> wrote:
            >
            > Hi,
            >
            > The original AMBE Addon board was designed and produced by Stefan (SR-Systems).
            > I see that there is some interests in it, so I decided to finish my sheet and layout for a compatible replacement.
            >
            > My previous device prototype 'DV-ATRX' uses a RJ45 8pin connector (standard 5V Yaesu pinning + rewiring facility).
            >
            > + Serial connection for keypads or displays
            > + or Up/Down/Fast key-inputs
            > - no low cost microphones
            > - only with external speaker (3.5mm jack)
            >
            > What is yours opinion? Which kind of microphone connector is the best?
            >
            > 73
            > Jan
            >
          • Will
            Jan, Even though some may think that the RJ45 is a shaky connector but is plentiful in stock and can be made to work just fine. So, I would say go for it and
            Message 5 of 10 , Dec 6, 2012
            • 0 Attachment
              Jan,

              Even though some may think that the RJ45 is a shaky connector but is
              plentiful in stock and can be made to work just fine. So, I would say go
              for it and lets use it,

              Will

              On 12/6/2012 8:43 AM, do1fjn wrote:
              > Hi,
              >
              > The original AMBE Addon board was designed and produced by Stefan (SR-Systems).
              > I see that there is some interests in it, so I decided to finish my sheet and layout for a compatible replacement.
              >
              > My previous device prototype 'DV-ATRX' uses a RJ45 8pin connector (standard 5V Yaesu pinning + rewiring facility).
              >
              > + Serial connection for keypads or displays
              > + or Up/Down/Fast key-inputs
              > - no low cost microphones
              > - only with external speaker (3.5mm jack)
              >
              > What is yours opinion? Which kind of microphone connector is the best?
              >
              > 73
              > Jan
              >
              >
              >
              >
              > ------------------------------------
              >
              > Yahoo! Groups Links
              >
              >
              >
              >
            • vk7yxx
              As the only person that seems to think the Kenwood-style connector is a good idea, I ll expand on my reasoning a bit: - Kenwood-style speaker/mics are cheap
              Message 6 of 10 , Dec 6, 2012
              • 0 Attachment
                As the only person that seems to think the Kenwood-style connector is a good idea, I'll expand on my reasoning a bit:

                - Kenwood-style speaker/mics are cheap and readily available, in fact I suspect most would already have one. Good quality ones can be had for $20, cheap ones for $10.
                - I see compatibility with the existing AMBE board as a big advantage, assuming the goal is to continue the DVRPTR V1 project rather than change its direction. If things progress and an upgraded AMBE board becomes available, I'd rather buy the new AMBE board, slide it into my existing box and plug my existing connections into it without modification, rather than get another mic and external speaker and modify the box (if it fits).
                - Having to connect a separate external speaker to use the DVRPTR in AMBE mode is painful, particularly for portable/mobile operations. The less connections required the better, and the Kenwood-style connections can be used separately if desired.

                73 - Don / VK7YXX.

                --- In DVRPTR_V1@yahoogroups.com, "do1fjn" <dvrptr@...> wrote:
                >
                > Hi,
                >
                > The original AMBE Addon board was designed and produced by Stefan (SR-Systems).
                > I see that there is some interests in it, so I decided to finish my sheet and layout for a compatible replacement.
                >
                > My previous device prototype 'DV-ATRX' uses a RJ45 8pin connector (standard 5V Yaesu pinning + rewiring facility).
                >
                > + Serial connection for keypads or displays
                > + or Up/Down/Fast key-inputs
                > - no low cost microphones
                > - only with external speaker (3.5mm jack)
                >
                > What is yours opinion? Which kind of microphone connector is the best?
                >
                > 73
                > Jan
                >
              • do1fjn
                Hi, ... Yes. The design allows huge connectors, like a Sub-D9 too. One more point against: - square cutout (not so easy for homemade like a round drill) 73 Jan
                Message 7 of 10 , Dec 7, 2012
                • 0 Attachment
                  Hi,

                  --- In DVRPTR_V1@yahoogroups.com, "vk7yxx" <vk7yxx@...> wrote:
                  > Would the RJ45 socket even fit in the standard DVRPTR V1 case?

                  Yes.
                  The design allows huge connectors, like a Sub-D9 too.

                  One more point against:
                  - square cutout (not so easy for homemade like a round drill)


                  73
                  Jan
                • do1fjn
                  Hi Don, ... Here a some disadvantages of this solution: - both jacks must be used together, no separate speaker is possible - no additional keys (for volume
                  Message 8 of 10 , Dec 7, 2012
                  • 0 Attachment
                    Hi Don,


                    --- In DVRPTR_V1@yahoogroups.com, "vk7yxx" <vk7yxx@...> wrote:
                    > - Kenwood-style speaker/mics are cheap and readily available, in fact I suspect most would already have one. Good quality ones can be had for $20, cheap ones for $10.

                    Here a some disadvantages of this solution:
                    - both jacks must be used together, no separate speaker is possible
                    - no additional keys (for volume control)
                    - possibility of damage the jacks
                    - an integrated speaker needs a separate NF-PA (the integrated Class-D is differential driven; no GND)


                    > - I see compatibility with the existing AMBE board as a big advantage, assuming the goal is to continue the DVRPTR V1 project rather than change its direction. If things progress and an upgraded AMBE board becomes available, I'd rather buy the new AMBE board, slide it into my existing box and plug my existing connections into it without modification, rather than get another mic and external speaker and modify the box (if it fits).

                    You're right - in case of replace the old board it's not ideal: A new front plate and a new microphone is needed.

                    > - Having to connect a separate external speaker to use the DVRPTR in AMBE mode is painful, particularly for portable/mobile operations. The less connections required the better, and the Kenwood-style connections can be used separately if desired.

                    I know, the best spkr/mic solution don't exists... A combination of a High-Ohm Speaker + Up/Down keys with an RJ45 for a low price...

                    So I open for ideas. A combination of a 4-pin 3.5mm jack + RJ45 + 3.5mm Speaker...
                    In the case of using a shared PTT/Mic line, a Volume-Poti is impossible and the firmware must support this (problem XDVRPTR FW).


                    73,
                    Jan
                  Your message has been successfully submitted and would be delivered to recipients shortly.