Loading ...
Sorry, an error occurred while loading the content.

Issue starting dongle / dvtool

Expand Messages
  • Ryan Drogo
    Hi All, I ve been having a heck of a time getting the DV Dongle running. Perhaps one of you can pinpoint where I ve gone wrong, or what I ve not tried. Here s
    Message 1 of 11 , Jan 10, 2013
    • 0 Attachment
      Hi All,

      I've been having a heck of a time getting the DV Dongle running. Perhaps one of you can pinpoint where I've gone wrong, or what I've not tried.

      Here's the rundown of what I've done thus far:

      Systems tried on:
      Netbook - Atom 1.2GHz processor, 2GB ram, Win 7 Ultimate 32-bit (severely underpowered machine, but tried anyhow)
      Laptop - Core i5 dual-core w/HT @ 2.5GHz, 4GB ram, Win 7 Enterprise 64-bit
      Workstation - 2x Xeon quad-core @ 2GHz, 32GB ram, Win 2008 R2

      I've had the same behavior on all the above systems. Here's the steps I've done, in order:

      Plug-in the dongle using a usb cable I had in the house (there was none in the box when I got home from HRO). 
      (Corollary: I've tried 4 different cables, all marked as usb2.0 rated, A to 5-pin mini B)

      Each system successfully located the drivers on windows update, and installed with no issues.
      Unplug dongle
      Rebooted system
      plugged in dongle, green light pulses slowly

      Load up the DvTool posted on the dvdongle.com website (currently the java based 1.x series).

      The systems had both jre 6 and 7 installed

      The tool loads right up, and pressing Open loads the firmware/version information successfully from the dongle.

      An audio loopback test (no ambe, straight audio) works great. 
      I've used both an analog connection to the systems' sound cards (typical laptop crap in the portables, and a soundblaster x-fi audio extreme pcie 

      in the workstation) and a usb headset I had lying around. 

      If I try to engage the chip, the first time around (whether I press ambe/loopback, record, or record to file) it sends a stream of 'audio output 

      buffer empty' messages. I cannot stop when record/record to file are used (it hangs). In all cases, it closes the connection on the stop button 

      with the following output: 
      sending ambe packet len 5
      receive watchdog timeout from localhost/127.0.0.1
      watchdog thread exit
      IOException receive socket closed
      disconnected from localhost/127.0.0.1
      Device localhost:20002 shutdown
      Device localhost:20002 closed

      If I try to Open again and then perform the same action, or another action, it closes the socket after a couple of seconds and I have to shut 

      down the program to try again. 

      Steps I've taken to get the java version working:

      turned off windows firewall
      turned off antivirus software
      run java as an admin
      set the ascpseriald.exe to run as an admin

      These all resulted in the same behavior as before.

      I then updated the VCP drivers from the ftdi website, rebooted the system, and plugged in the dongle again. The drivers updated (as evidenced by 

      the 'installing new hardware' bubble coming up again) and then the same behavior ensues.

      Here's a sample of the ascp.txt log file:
      ascp starting
      connect from 127.0.0.1:63816
      facu 0/0 tacu 0/0 fncu 0/0 fcu 1000/0/0
      write ctrl buf 4 20 1 0 len 4 wlen 4
      write ctrl buf 4 20 2 0 len 4 wlen 4
      write ctrl buf 5 20 4 0 len 5 wlen 5
      pktlen   14 type 0 from ambe 0/0 worklen 34 (0e 00 01 00 44)
      control packet from ambe 14 (0/0) -> 0e 00 01 00 44 56 20 44 6f 6e 67 6c 65 00 
      pktlen   13 type 0 from ambe 0/0 worklen 20 (0d 00 02 00 44)
      control packet from ambe 13 (0/0) -> 0d 00 02 00 44 56 31 30 34 30 31 36 00 
      pktlen    7 type 0 from ambe 0/0 worklen 7 (07 00 04 00 00)
      control packet from ambe 7 (0/0) -> 07 00 04 00 00 68 00 
      write ctrl buf 5 20 4 0 len 5 wlen 5
      pktlen    7 type 0 from ambe 0/0 worklen 7 (07 00 04 00 01)
      control packet from ambe 7 (0/0) -> 07 00 04 00 01 6f 00 
      write ctrl buf 5 0 18 0 len 5 wlen 5
      pktlen    5 type 0 from ambe 0/0 worklen 58 (05 00 18 00 01)
      control packet from ambe 5 (0/0) -> 05 00 18 00 01 
      uncompressed buffer underrun facu 0/1 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 1/1 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 1/2 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 2/2 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 2/3 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 3/3 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 3/4 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 4/4 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 4/5 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 5/5 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 5/6 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 6/6 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 6/7 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 7/7 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 7/8 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 8/8 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 8/9 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 9/9 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 9/10 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 10/10 tacu 0/0 fncu 0/0 fcu 1000/0/0
      uncompressed buffer underrun facu 10/11 tacu 0/0 fncu 0/0 fcu 1000/0/0
      compressed buffer underrun facu 11/11 tacu 0/0 fncu 0/0 fcu 1000/0/0
      pktlen    0 type 0 from ambe 11/11 worklen 1629 (00 00 00 00 00)
      bad pktlen 0 (11/11)
      00 00 00 00 00

      So then I tried the 2.0beta5 version. On all systems, this produces the dreaded No DV Dongle found message, despite the dongle being attached and 

      the light pulsing slowly. 

      Following the advice I've found here on the boards, I've then tried:

      Simply re-installing the FTDI driver from their website
      Running the FTDI clean utility, rebooting, re-installing FTDI site drivers
      Running the CDM Uninstaller, rebooting, re-installing FTDI site drivers
      same as above, but re-installing the ones from windows update by just plugging in the dongle

      If I run listVCP.exe or the ftdireg.bat files I get what appears to be good output. For example, here's the current output of listvcp from the 

      laptop with the dongle plugged in: 

      >> HARDWARE\DEVICEMAP\SERIALCOMM
      namebuf=(\Device\VCP0) namesize=12 valuebuf=(COM4) valuesize=5 ret=0
      \Device\VCP0=COM4

      >> SYSTEM\CurrentControlSet\Enum\FTDIBUS
      namebuf=(VID_0403+PID_6001+6&335c4957&0&2) namesize=32 ret=0
      SYSTEM\CurrentControlSet\Enum\FTDIBUS\VID_0403+PID_6001+6&335c4957&0&2=6&335c4957&0&2
      namebuf=(0000) namesize=4 ret=0
      namebuf=(Device Parameters) namesize=17 ret=0
      namebuf=(LogConf) namesize=7 ret=0
      namebuf=(Properties) namesize=10 ret=0
      namebuf=(Control) namesize=7 ret=0
      namebuf=(DeviceDesc) namesize=10 valuebuf=(@...,%vid_0403&pid_6001.devicedesc%;USB Serial Port) valuesize=58 ret=0

      namebuf=(Capabilities) namesize=12 valuebuf=(É) valuesize=4 ret=0
      namebuf=(HardwareID) namesize=10 valuebuf=(FTDIBUS\COMPORT&VID_0403&PID_6001) valuesize=35 ret=0
      namebuf=(ContainerID) namesize=11 valuebuf=({b5d18f09-55fe-11e2-b8e1-f0def186c93b}) valuesize=39 ret=0
      namebuf=(ConfigFlags) namesize=11 valuebuf=() valuesize=4 ret=0
      namebuf=(ClassGUID) namesize=9 valuebuf=({4d36e978-e325-11ce-bfc1-08002be10318}) valuesize=39 ret=0
      namebuf=(Driver) namesize=6 valuebuf=({4d36e978-e325-11ce-bfc1-08002be10318}\0001) valuesize=44 ret=0
      namebuf=(UpperFilters) namesize=12 valuebuf=(serenum) valuesize=9 ret=0
      namebuf=(Class) namesize=5 valuebuf=(Ports) valuesize=6 ret=0
      namebuf=(Mfg) namesize=3 valuebuf=(@...,%ftdi%;FTDI) valuesize=23 ret=0
      namebuf=(Service) namesize=7 valuebuf=(FTSER2K) valuesize=8 ret=0
      namebuf=(FriendlyName) namesize=12 valuebuf=(USB Serial Port (COM4)) valuesize=23 ret=0

      >> SYSTEM\CurrentControlSet\Services\FTDIBUS\Enum
      namebuf=(Count) namesize=5 valuebuf=(?) valuesize=4 ret=0
      namebuf=(NextInstance) namesize=12 valuebuf=(?) valuesize=4 ret=0
      namebuf=(0) namesize=1 valuebuf=(USB\VID_0403&PID_6001\6&335c4957&0&2) valuesize=37 ret=0
      SYSTEM\CurrentControlSet\Enum\FTDIBUS\VID_0403+PID_6001+6&335c4957&0&2A\0000=6&335c4957&0&2
      regopenkeyexa 3 namebuf=(SYSTEM\CurrentControlSet\Enum\FTDIBUS\VID_0403+PID_6001+6&335c4957&0&2A\0000) ret=2
      namebuf=(NextInstance) namesize=12 valuebuf=() valuesize=4 ret=0

      I get similar output on the other systems - that is, it looks like the ports are present and properly enumerated in the registry.

      Anyone point me in the right direction of something to try next, or is there any other debug output I can provide?

      Thanks very much!
      A D-Star Newbie
      Ryan
      KI6ZLC
    • rdrogo
      As a followup, I ve now also tried: 1) Using the DVToolTest.exe file instead of DVTool.exe. If I do that, I still get the not found error, and get the
      Message 2 of 11 , Jan 21, 2013
      • 0 Attachment
        As a followup, I've now also tried:

        1) Using the DVToolTest.exe file instead of DVTool.exe. If I do that, I still get the not found error, and get the following information in the console:
        Searching 1 FTDI serial devices
        Found FTDI device at index 0 location 530 serial description USB <-> Serial
        Skipping FTDI Device USB <-> Serial
        Found 0 FTDI device(s)

        2) I gave the dongle to a friend to try on his system, and he reported the same behavior as I described above.


        Thanks,
        Ryan
        KI6ZLC
      • vk4tux
        From Win8 the DVTool not found also happens and just needs a retry, then; Qt: Untested Windows version 6.2 detected! DVTool version 2.0beta5 Restored
        Message 3 of 11 , Jan 21, 2013
        • 0 Attachment
          From Win8 the DVTool not found also happens and just needs a retry, then;


          Qt: Untested Windows version 6.2 detected!
          DVTool version 2.0beta5
          Restored parameters:
          UserCallsign=KA8SCP D
          UserMessage=Adrian Win8
          DVDevice=COM10
          AudioInDevice=Microphone (4- Logitech USB Hea
          AudioOutDevice=Speakers (4- Logitech USB Heads
          Gateway=WB1GOF
          Module=C
          FavoriteGW=N
          PTTLock=Y
          AutoReconnect=N
          Style=Windows
          Colors=Default
          FavoriteGWList=
          O/S: Windows UNKNOWN
          name=Microphone (SoundMAX Integrated
          channels=1 2
          frequencies=8000 11025 22050 44100 48000 96000
          byte orders=1
          codecs=audio/pcm
          samplesizes=8 16
          sampletypes=1 2

          name=Line In (SoundMAX Integrated Di
          channels=1 2
          frequencies=8000 11025 22050 44100 48000 96000
          byte orders=1
          codecs=audio/pcm
          samplesizes=8 16
          sampletypes=1 2

          name=default
          channels=1 2
          frequencies=8000 11025 22050 44100 48000 96000
          byte orders=1
          codecs=audio/pcm
          samplesizes=8 16
          sampletypes=1 2

          name=Speakers (SoundMAX Integrated D
          channels=1 2 4 6 8
          frequencies=8000 11025 22050 44100 48000 96000
          byte orders=1
          codecs=audio/pcm
          samplesizes=8 16
          sampletypes=1 2

          name=default
          channels=1 2 4 6 8
          frequencies=8000 11025 22050 44100 48000 96000
          byte orders=1
          codecs=audio/pcm
          samplesizes=8 16
          sampletypes=1 2

          Input devices: Microphone (SoundMAX Integrated Line In (SoundMAX Integrated Di d
          efault
          Output devices: Speakers (SoundMAX Integrated D default
          FTDI serial device on VCP port COM10
          FTDI serial device COM10 valid
          Added audio input device: Microphone (SoundMAX Integrated
          Audio input device changed to Microphone (SoundMAX Integrated
          Added audio input device: Line In (SoundMAX Integrated Di
          Added audio input device: default
          Added audio output device: Speakers (SoundMAX Integrated D
          Audio output device changed to Speakers (SoundMAX Integrated D
          Added audio output device: default
          Style changed to Windows
          Found 1 FTDI device(s)
          Available builtin palettes:
          BlackOnMellon
          BlackOnPink
          BlackOnSeaMist
          Default
          GoldOnBlack
          WhiteOnDarkRed
          WhiteOnNavyBlue
          WhiteOnPurpleBlue
          WhiteOnSteelBlue
          WhiteOnTeal
          Available external palettes:
          Loaded palette :/dvtoolresources/palettes/BlackOnMellon.qpalette
          Loaded palette :/dvtoolresources/palettes/Default.qpalette
          Module changed to A
          Module changed from A to C

          Driver info; FTDI ver 2.8.24.0 driver date 10/4/2010 < Au format

          Driver Management has concluded the process to add Service FTSER2K for Device Instance ID FTDIBUS\VID_0403+PID_6001+A9004UNMA\0000 with the following status: 0.

          Driver Management has concluded the process to add Service Serenum for Device Instance ID FTDIBUS\VID_0403+PID_6001+A9004UNMA\0000 with the following status: 0.

          Driver Management concluded the process to install driver ftdiport.inf_x86_82e6432d4f9259e1\ftdiport.inf for Device Instance ID FTDIBUS\VID_0403+PID_6001+A9004UNMA\0000 with the following status: 0x0.


          vk4tux
        • vk2ah
          Hi, Try running Dv tool2.beta 5. This may help you out. Regards VK2AH
          Message 4 of 11 , Jan 21, 2013
          • 0 Attachment
            Hi, Try running Dv tool2.beta 5.
            This may help you out. Regards VK2AH

            --- In DVDongle@yahoogroups.com, Ryan Drogo wrote:
            >
            > Hi All,
            >
            > I've been having a heck of a time getting the DV Dongle running. Perhaps one of you can pinpoint where I've gone wrong, or what I've not tried.
            >
            > Here's the rundown of what I've done thus far:
            >
            > Systems tried on:
            > Netbook - Atom 1.2GHz processor, 2GB ram, Win 7 Ultimate 32-bit (severely underpowered machine, but tried anyhow)
            > Laptop - Core i5 dual-core w/HT @ 2.5GHz, 4GB ram, Win 7 Enterprise 64-bit
            > Workstation - 2x Xeon quad-core @ 2GHz, 32GB ram, Win 2008 R2
            >
            > I've had the same behavior on all the above systems. Here's the steps I've done, in order:
            >
            > Plug-in the dongle using a usb cable I had in the house (there was none in the box when I got home from HRO). 
            > (Corollary: I've tried 4 different cables, all marked as usb2.0 rated, A to 5-pin mini B)
            >
            > Each system successfully located the drivers on windows update, and installed with no issues.
            > Unplug dongle
            > Rebooted system
            > plugged in dongle, green light pulses slowly
            >
            > Load up the DvTool posted on the dvdongle.com website (currently the java based 1.x series).
            >
            > The systems had both jre 6 and 7 installed
            >
            > The tool loads right up, and pressing Open loads the firmware/version information successfully from the dongle.
            >
            > An audio loopback test (no ambe, straight audio) works great. 
            > I've used both an analog connection to the systems' sound cards (typical laptop crap in the portables, and a soundblaster x-fi audio extreme pcie 
            >
            > in the workstation) and a usb headset I had lying around. 
            >
            > If I try to engage the chip, the first time around (whether I press ambe/loopback, record, or record to file) it sends a stream of 'audio output 
            >
            > buffer empty' messages. I cannot stop when record/record to file are used (it hangs). In all cases, it closes the connection on the stop button 
            >
            > with the following output: 
            > sending ambe packet len 5
            > receive watchdog timeout from localhost/127.0.0.1
            > watchdog thread exit
            > IOException receive socket closed
            > disconnected from localhost/127.0.0.1
            > Device localhost:20002 shutdown
            > Device localhost:20002 closed
            >
            > If I try to Open again and then perform the same action, or another action, it closes the socket after a couple of seconds and I have to shut 
            >
            > down the program to try again. 
            >
            > Steps I've taken to get the java version working:
            >
            > turned off windows firewall
            > turned off antivirus software
            > run java as an admin
            > set the ascpseriald.exe to run as an admin
            >
            > These all resulted in the same behavior as before.
            >
            > I then updated the VCP drivers from the ftdi website, rebooted the system, and plugged in the dongle again. The drivers updated (as evidenced by 
            >
            > the 'installing new hardware' bubble coming up again) and then the same behavior ensues.
            >
            > Here's a sample of the ascp.txt log file:
            > ascp starting
            > connect from 127.0.0.1:63816
            > facu 0/0 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > write ctrlbuf 4 20 1 0 len 4 wlen 4
            > write ctrlbuf 4 20 2 0 len 4 wlen 4
            > write ctrlbuf 5 20 4 0 len 5 wlen 5
            > pktlen   14 type 0 from ambe 0/0 worklen 34 (0e 00 01 00 44)
            > control packet from ambe 14 (0/0) -> 0e 00 01 00 44 56 20 44 6f 6e 67 6c 65 00 
            > pktlen   13 type 0 from ambe 0/0 worklen 20 (0d 00 02 00 44)
            > control packet from ambe 13 (0/0) -> 0d 00 02 00 44 56 31 30 34 30 31 36 00 
            > pktlen    7 type 0 from ambe 0/0 worklen 7 (07 00 04 00 00)
            > control packet from ambe 7 (0/0) -> 07 00 04 00 00 68 00 
            > write ctrlbuf 5 20 4 0 len 5 wlen 5
            > pktlen    7 type 0 from ambe 0/0 worklen 7 (07 00 04 00 01)
            > control packet from ambe 7 (0/0) -> 07 00 04 00 01 6f 00 
            > write ctrlbuf 5 0 18 0 len 5 wlen 5
            > pktlen    5 type 0 from ambe 0/0 worklen 58 (05 00 18 00 01)
            > control packet from ambe 5 (0/0) -> 05 00 18 00 01 
            > uncompressed buffer underrunfacu 0/1 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 1/1 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 1/2 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 2/2 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 2/3 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 3/3 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 3/4 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 4/4 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 4/5 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 5/5 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 5/6 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 6/6 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 6/7 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 7/7 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 7/8 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 8/8 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 8/9 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 9/9 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 9/10 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 10/10 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > uncompressed buffer underrunfacu 10/11 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > compressed buffer underrunfacu 11/11 tacu 0/0 fncu 0/0 fcu 1000/0/0
            > pktlen    0 type 0 from ambe 11/11 worklen 1629 (00 00 00 00 00)
            > bad pktlen 0 (11/11)
            > 00 00 00 00 00
            >
            > So then I tried the 2.0beta5 version. On all systems, this produces the dreaded No DV Dongle found message, despite the dongle being attached and 
            >
            > the light pulsing slowly. 
            >
            > Following the advice I've found here on the boards, I've then tried:
            >
            > Simply re-installing the FTDI driver from their website
            > Running the FTDI clean utility, rebooting, re-installing FTDI site drivers
            > Running the CDMUninstaller, rebooting, re-installing FTDI site drivers
            > same as above, but re-installing the ones from windows update by just plugging in the dongle
            >
            > If I run listVCP.exe or the ftdireg.bat files I get what appears to be good output. For example, here's the current output of listvcp from the 
            >
            > laptop with the dongle plugged in: 
            >
            > >> HARDWARE\DEVICEMAP\SERIALCOMM
            > namebuf=(\Device\VCP0) namesize=12 valuebuf=(COM4) valuesize=5 ret=0
            > \Device\VCP0=COM4
            >
            > >> SYSTEM\CurrentControlSet\Enum\FTDIBUS
            > namebuf=(VID_0403+PID_6001+6&335c4957&0&2) namesize=32 ret=0
            > SYSTEM\CurrentControlSet\Enum\FTDIBUS\VID_0403+PID_6001+6&335c4957&0&2=6&335c4957&0&2
            > namebuf=(0000) namesize=4 ret=0
            > namebuf=(Device Parameters) namesize=17 ret=0
            > namebuf=(LogConf) namesize=7 ret=0
            > namebuf=(Properties) namesize=10 ret=0
            > namebuf=(Control) namesize=7 ret=0
            > namebuf=(DeviceDesc) namesize=10 valuebuf=(@...,%vid_0403&pid_6001.devicedesc%;USB Serial Port) valuesize=58 ret=0
            >
            > namebuf=(Capabilities) namesize=12 valuebuf=(É) valuesize=4 ret=0
            > namebuf=(HardwareID) namesize=10 valuebuf=(FTDIBUS\COMPORT&VID_0403&PID_6001) valuesize=35 ret=0
            > namebuf=(ContainerID) namesize=11 valuebuf=({b5d18f09-55fe-11e2-b8e1-f0def186c93b}) valuesize=39 ret=0
            > namebuf=(ConfigFlags) namesize=11 valuebuf=() valuesize=4 ret=0
            > namebuf=(ClassGUID) namesize=9 valuebuf=({4d36e978-e325-11ce-bfc1-08002be10318}) valuesize=39 ret=0
            > namebuf=(Driver) namesize=6 valuebuf=({4d36e978-e325-11ce-bfc1-08002be10318}\0001) valuesize=44 ret=0
            > namebuf=(UpperFilters) namesize=12 valuebuf=(serenum) valuesize=9 ret=0
            > namebuf=(Class) namesize=5 valuebuf=(Ports) valuesize=6 ret=0
            > namebuf=(Mfg) namesize=3 valuebuf=(@...,%ftdi%;FTDI) valuesize=23 ret=0
            > namebuf=(Service) namesize=7 valuebuf=(FTSER2K) valuesize=8 ret=0
            > namebuf=(FriendlyName) namesize=12 valuebuf=(USB Serial Port (COM4)) valuesize=23 ret=0
            >
            > >> SYSTEM\CurrentControlSet\Services\FTDIBUS\Enum
            > namebuf=(Count) namesize=5 valuebuf=(?) valuesize=4 ret=0
            > namebuf=(NextInstance) namesize=12 valuebuf=(?) valuesize=4 ret=0
            > namebuf=(0) namesize=1 valuebuf=(USB\VID_0403&PID_6001\6&335c4957&0&2) valuesize=37 ret=0
            > SYSTEM\CurrentControlSet\Enum\FTDIBUS\VID_0403+PID_6001+6&335c4957&0&2A\0000=6&335c4957&0&2
            > regopenkeyexa 3 namebuf=(SYSTEM\CurrentControlSet\Enum\FTDIBUS\VID_0403+PID_6001+6&335c4957&0&2A\0000) ret=2
            > namebuf=(NextInstance) namesize=12 valuebuf=() valuesize=4 ret=0
            >
            > I get similar output on the other systems - that is, it looks like the ports are present and properly enumerated in the registry.
            >
            > Anyone point me in the right direction of something to try next, or is there any other debug output I can provide?
            >
            > Thanks very much!
            > A D-Star Newbie
            > Ryan
            > KI6ZLC
            >
          • vk4tux
            ... He did; So then I tried the 2.0beta5 version. On all systems, this produces the dreaded No DV Dongle found message, despite the dongle being attached
            Message 5 of 11 , Jan 21, 2013
            • 0 Attachment
              --- In DVDongle@yahoogroups.com, "vk2ah" wrote:
              >
              > Hi, Try running Dv tool2.beta 5.
              > This may help you out. Regards VK2AH

              He did;

              "> So then I tried the 2.0beta5 version. On all systems, this produces the dreaded No DV Dongle found message, despite the dongle being attached and
              >
              > the light pulsing slowly.
              >
              > Following the advice I've found here on the boards, I've then tried:
              >
              "

              vk4tux
            • vk4tux
              I would be posting the DVDongle to Robin AA4RC to test. Seems like a rare FTDI chip/hardware issue. I had a rare issue with a serial number on one of mine and
              Message 6 of 11 , Jan 21, 2013
              • 0 Attachment
                I would be posting the DVDongle to Robin AA4RC to test.
                Seems like a rare FTDI chip/hardware issue. I had a rare issue with a serial number on one of mine and Robin provided guidance on reprogramming the correct FTDI serial (not DV s/n).

                good luck

                vk4tux



                --- In DVDongle@yahoogroups.com, "rdrogo" wrote:
                >
                >
                >
                > As a followup, I've now also tried:
                >
                > 1) Using the DVToolTest.exe file instead of DVTool.exe. If I do that, I still get the not found error, and get the following information in the console:
                > Searching 1 FTDI serial devices
                > Found FTDI device at index 0 location 530 serial description USB <-> Serial
                > Skipping FTDI Device USB <-> Serial
                > Found 0 FTDI device(s)
                >
                > 2) I gave the dongle to a friend to try on his system, and he reported the same behavior as I described above.
                >
                >
                > Thanks,
                > Ryan
                > KI6ZLC
                >
              • Kevin Wesolowski
                Did you use the driver package in http://www.ftdichip.com/Drivers/VCP.htm ??? Kevin KD7DFV From: rdrogo [mailto:psychohamster@yahoo.com] Sent: Monday, January
                Message 7 of 11 , Jan 21, 2013
                • 0 Attachment

                  Did you use the driver package in

                  http://www.ftdichip.com/Drivers/VCP.htm

                  ???

                   

                  Kevin

                  KD7DFV

                   

                  From: rdrogo [mailto:psychohamster@...]
                  Sent: Monday, January 21, 2013 11:57 AM
                  To: DVDongle@yahoogroups.com
                  Subject: [DVDongle] Re: Issue starting dongle / dvtool

                   

                   



                  As a followup, I've now also tried:

                  1) Using the DVToolTest.exe file instead of DVTool.exe. If I do that, I still get the not found error, and get the following information in the console:
                  Searching 1 FTDI serial devices
                  Found FTDI device at index 0 location 530 serial description USB <-> Serial
                  Skipping FTDI Device USB <-> Serial
                  Found 0 FTDI device(s)

                  2) I gave the dongle to a friend to try on his system, and he reported the same behavior as I described above.

                  Thanks,
                  Ryan
                  KI6ZLC

                • rdrogo
                  Yup, sure did.
                  Message 8 of 11 , Jan 22, 2013
                  • 0 Attachment
                    Yup, sure did.

                    --- In DVDongle@yahoogroups.com, "Kevin Wesolowski" wrote:
                    >
                    > Did you use the driver package in
                    >
                    > http://www.ftdichip.com/Drivers/VCP.htm
                    >
                    > ???
                    >
                    >
                    >
                    > Kevin
                    >
                    > KD7DFV
                    >
                    >
                    >
                    > From: rdrogo [mailto:psychohamster@...]
                    > Sent: Monday, January 21, 2013 11:57 AM
                    > To: DVDongle@yahoogroups.com
                    > Subject: [DVDongle] Re: Issue starting dongle / dvtool
                    >
                    >
                    >
                    >
                    >
                    >
                    >
                    > As a followup, I've now also tried:
                    >
                    > 1) Using the DVToolTest.exe file instead of DVTool.exe. If I do that, I
                    > still get the not found error, and get the following information in the
                    > console:
                    > Searching 1 FTDI serial devices
                    > Found FTDI device at index 0 location 530 serial description USB <-> Serial
                    > Skipping FTDI Device USB <-> Serial
                    > Found 0 FTDI device(s)
                    >
                    > 2) I gave the dongle to a friend to try on his system, and he reported the
                    > same behavior as I described above.
                    >
                    > Thanks,
                    > Ryan
                    > KI6ZLC
                    >
                  • Woodrick, Ed
                    Ryan, Not sure what your problem is, but there s evidently something different about your environment. I ve loaded the DVTool beta on a number of computers and
                    Message 9 of 11 , Jan 22, 2013
                    • 0 Attachment

                      Ryan,

                       

                      Not sure what your problem is, but there’s evidently something different about your environment.

                       

                      I’ve loaded the DVTool beta on a number of computers and haven’t had any issues with it. Basically, my rules are:

                      ·         Make sure that the computer has Internet connectivity

                      ·         Insert DVDongle

                      ·         Wait for drivers to be downloaded and installed

                      ·         Start the DVTool software

                       

                      Look for something else that may try to talk to the chip. Anything that supports serial, GPS, mouse, etc?.

                       

                      Look in device Manager under Ports. Do you see a USB Serial Port? What com port number is it?

                       

                      And yes, I’ve run the DVDongle on Windows Vista x32 and x64, Windows 7, x32 and x64, as well as Windows 8, x32 and x64. They all work well and have been no problems for me. And I’ve also run it on an Atom Netbook with no issues.

                       

                      Ed WA4YIH

                       

                      From: DVDongle@yahoogroups.com [mailto:DVDongle@yahoogroups.com] On Behalf Of rdrogo
                      Sent: Monday, January 21, 2013 1:57 PM
                      To: DVDongle@yahoogroups.com
                      Subject: [DVDongle] Re: Issue starting dongle / dvtool

                       

                       



                      As a followup, I've now also tried:

                      1) Using the DVToolTest.exe file instead of DVTool.exe. If I do that, I still get the not found error, and get the following information in the console:
                      Searching 1 FTDI serial devices
                      Found FTDI device at index 0 location 530 serial description USB <-> Serial
                      Skipping FTDI Device USB <-> Serial
                      Found 0 FTDI device(s)

                      2) I gave the dongle to a friend to try on his system, and he reported the same behavior as I described above.

                      Thanks,
                      Ryan
                      KI6ZLC

                    • rdrogo
                      Yeah, I think that s what I m getting towards. I ve been working in a separate email thread with Robin as well, but so far no luck. I ve also now tried the
                      Message 10 of 11 , Jan 25, 2013
                      • 0 Attachment
                        Yeah, I think that's what I'm getting towards. I've been working in a separate email thread with Robin as well, but so far no luck.

                        I've also now tried the dongle on a mac (OS 10.8) and linux (CentOS) machines, with the same result in the java version (closed connection). Couldn't try 2.0 because of code signing policy on the mac and the CentOS machine doesn't have the right ABI support (it's about a year old distro).

                        --- In DVDongle@yahoogroups.com, "vk4tux" wrote:
                        >
                        > I would be posting the DVDongle to Robin AA4RC to test.
                        > Seems like a rare FTDI chip/hardware issue. I had a rare issue with a serial number on one of mine and Robin provided guidance on reprogramming the correct FTDI serial (not DV s/n).
                        >
                        > good luck
                        >
                        > vk4tux
                        >
                        >
                        >
                        > --- In DVDongle@yahoogroups.com, "rdrogo" wrote:
                        > >
                        > >
                        > >
                        > > As a followup, I've now also tried:
                        > >
                        > > 1) Using the DVToolTest.exe file instead of DVTool.exe. If I do that, I still get the not found error, and get the following information in the console:
                        > > Searching 1 FTDI serial devices
                        > > Found FTDI device at index 0 location 530 serial description USB <-> Serial
                        > > Skipping FTDI Device USB <-> Serial
                        > > Found 0 FTDI device(s)
                        > >
                        > > 2) I gave the dongle to a friend to try on his system, and he reported the same behavior as I described above.
                        > >
                        > >
                        > > Thanks,
                        > > Ryan
                        > > KI6ZLC
                        > >
                        >
                      • Adrian
                        Yeah, I think that s what I m getting towards. I ve been working in a separate email thread with Robin as well, but so far no luck. I ve also now tried the
                        Message 11 of 11 , Jan 25, 2013
                        • 0 Attachment


                            Yeah, I think that's what I'm getting towards. I've been working in a separate email thread with Robin as well, but so far no luck.

                          I've also now tried the dongle on a mac (OS 10.8) and linux (CentOS) machines, with the same result in the java version (closed connection). Couldn't try 2.0 because of code signing policy on the mac and the CentOS machine doesn't have the right ABI support (it's about a year old distro).



                          Ok on that, CentOS should be fine, I currently am using fedora 18.

                          Try run > #dmesg in terminal

                          12.482991] usbcore: registered new interface driver ftdi_sio
                          [   12.483078] usbserial: USB Serial support registered for FTDI USB Serial Device
                          [   12.483128] ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected
                          [   12.483151] usb 2-1: Detected FT232RL
                          [   12.483153] usb 2-1: Number of endpoints 2
                          [   12.483155] usb 2-1: Endpoint 1 MaxPacketSize 64
                          [   12.483157] usb 2-1: Endpoint 2 MaxPacketSize 64
                          [   12.483158] usb 2-1: Setting MaxPacketSize 64
                          [   12.485786] usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0
                          [   12.485809] ftdi_sio 3-1:1.0: FTDI USB Serial Device converter detected
                          [   12.485827] usb 3-1: Detected FT232RL
                          [   12.485829] usb 3-1: Number of endpoints 2
                          [   12.485830] usb 3-1: Endpoint 1 MaxPacketSize 64
                          [   12.485832] usb 3-1: Endpoint 2 MaxPacketSize 64
                          [   12.485834] usb 3-1: Setting MaxPacketSize 64
                          [   12.487973] usb 3-1: FTDI USB Serial Device converter now attached to ttyUSB1

                          ttyUSB0 =DV Dongle
                          ttyUSB1 = Dvap


                          I link the script executable (DVTool.sh with modified path) to usr/bin/DVTool

                          ln -s /root/Downloads/DVTool/DVTool.sh /usr/bin/DVTool

                          so;

                          [root@fedora18desk ~]# DVTool
                          DVTool version 2.0beta5
                          Restored parameters:
                            UserCallsign=VK4TUX
                            UserMessage=Adrian 
                            DVDevice=/dev/ttyUSB0
                            AudioInDevice=sysdefault:CARD=Headset
                            AudioOutDevice=sysdefault:CARD=Headset
                            Gateway=REF001
                            Module=C
                            FavoriteGW=N
                            PTTLock=N
                            AutoReconnect=N
                            Style=Cleanlooks
                            Colors=BlackOnSeaMist
                            FavoriteGWList=
                          O/S: Linux
                          name=sysdefault:CARD=Intel
                          channels=1 2 
                          frequencies=8000 11025 22050 44100 48000 
                          byte orders=1 0 
                          codecs=audio/pcm 
                          samplesizes=8 16 32 
                          sampletypes=1 2 3 

                          name=sysdefault:CARD=Headset
                          channels=1 2 
                          frequencies=8000 11025 22050 44100 48000 
                          byte orders=1 0 
                          codecs=audio/pcm 
                          samplesizes=8 16 32 
                          sampletypes=1 2 3 

                          name=default
                          channels=1 2 
                          frequencies=8000 11025 22050 44100 48000 
                          byte orders=1 0 
                          codecs=audio/pcm 
                          samplesizes=8 16 32 
                          sampletypes=1 2 3 

                          name=sysdefault:CARD=Intel
                          channels=1 2 4 6 8 
                          frequencies=8000 11025 22050 44100 48000 
                          byte orders=1 0 
                          codecs=audio/pcm 
                          samplesizes=8 16 32 
                          sampletypes=1 2 3 

                          name=sysdefault:CARD=Headset
                          channels=1 2 4 6 8 
                          frequencies=8000 11025 22050 44100 48000 
                          byte orders=1 0 
                          codecs=audio/pcm 
                          samplesizes=8 16 32 
                          sampletypes=1 2 3 

                          name=default
                          channels=1 2 4 6 8 
                          frequencies=8000 11025 22050 44100 48000 
                          byte orders=1 0 
                          codecs=audio/pcm 
                          samplesizes=8 16 32 
                          sampletypes=1 2 3 

                          Input devices: sysdefault:CARD=Intel sysdefault:CARD=Headset default 
                          Output devices: sysdefault:CARD=Intel sysdefault:CARD=Headset default 
                          FTDI serial device ttyUSB0 found (A9003R9J)
                          FTDI serial device ttyUSB1 found (A6007ELQ)
                          Module changed to A
                          Module changed from A to C
                          Added audio input device: sysdefault:CARD=Intel
                          Audio input device changed to sysdefault:CARD=Intel
                          Added audio input device: sysdefault:CARD=Headset
                          Audio input device changed to sysdefault:CARD=Headset
                          Added audio input device: default
                          Added audio output device: sysdefault:CARD=Intel
                          Audio output device changed to sysdefault:CARD=Intel
                          Added audio output device: sysdefault:CARD=Headset
                          Audio output device changed to sysdefault:CARD=Headset
                          Added audio output device: default
                          Style changed to Windows
                          Style changed to Cleanlooks
                          Found 2 FTDI device(s)
                          Available builtin palettes:
                          BlackOnMellon
                          BlackOnPink
                          BlackOnSeaMist
                          Default
                          GoldOnBlack
                          WhiteOnDarkRed
                          WhiteOnNavyBlue
                          WhiteOnPurpleBlue
                          WhiteOnSteelBlue
                          WhiteOnTeal
                          Available external palettes:
                          Test
                          Loaded palette :/dvtoolresources/palettes/BlackOnMellon.qpalette
                          Loaded palette :/dvtoolresources/palettes/BlackOnSeaMist.qpalette




                          Good Luck

                          Adrian ... vk4tux
                        Your message has been successfully submitted and would be delivered to recipients shortly.