Loading ...
Sorry, an error occurred while loading the content.

Messages List

10181

Re: Compression and Kickstart Gears

Thanks CK, I was thinking that the idler gear would slip out of mesh and lock the gearbox up but there must be enough left at the tooth root to keep the teeth
waters5cl
Feb 5
#10181
 
10180

Re: Compression and Kickstart Gears

Hi Craig, Nor much experience with high CR pistons but my race motors generally run in the 9.5-10.5 area. No problem kicking over, but I have lost a few teeth
macchirace
Jan 26
#10180
 
10179

Re: Compression and Kickstart Gears

Anyone? T.ray? Would appreciate any advice / experience. Thanks, Craig
waters5cl
Jan 25
#10179
 
10178

Bottom Fork Cover Mounts

Hey all, I am currently in the middle of a complete restoration of a 1972 CB125s. Things have been going surprisingly smoothly until I started reassembling my
cwlaertes
Jan 22
#10178
 
10177

Re: Big Pro and Amateur Flat Track Race Feb 14th

This is great news Chris! Looking forward to seeing you out there for the show! On Wed, Jan 13, 2016 at 7:52 AM, 'Macchiracer' macchi@... [CB125] < ...
    Patrick Farrell
    Jan 17
    #10177
    This message has attachments
    10176

    Big Pro and Amateur Flat Track Race Feb 14th

    My Honda SL125 named "Junior" has been entered in Open Vintage for the big show. I'll probably be the oldest rider at 63 years. Chris Kerber Salem Speedway Jan
      Macchiracer
      Jan 17
      #10176
      This message has attachments
      10175

      Re: 1971 Tank Needed

      I have a nice tank from an SL125S Has been primed with automotive primer but has a couple dentsalso needs a new petcock valve. From: "switch1685@...
      Jason P
      Jan 12
      #10175
       
      10174

      Re: 1971 Tank Needed

      How bad is your tank? Mine was horribly rusted but eventually cleaned up and is in good use on my 72 CL100. Used POR15 as the urethane liner.  These tanks do
      RICK WESTERFIELD
      Jan 12
      #10174
       
      10173

      Re: engine rebuild

      I agree with t.ray. It's not a direct bolt on requiring cases to be bored and there was some piston crown trimming required. This cylinder has a thick liner
      Scott Kirn
      Jan 12
      #10173
       
      10172

      Re: engine rebuild

      Like Terry says  the 144 will not fit the early motors with out case work...the one I am using  is ...not this exact kit... but a jug that measures 56.5
      buzzy
      Jan 11
      #10172
       
      10171

      Re: engine rebuild

      I will say this once again. The 144 kit on ebay is NOT a direct bolt on to earlier 125. Spigot will not fit in case and pistons are wrong for 1 piece heads
      t.raymiller@...
      Jan 11
      #10171
       
      10170

      1971 Tank Needed

      Hey folks! Im rebuilding a '71 CL100 and it needs a new tank. Any have a tank they are looking to sell?
      switch1685
      Jan 11
      #10170
       
      10169

      Re: engine rebuild

      They are available in kits here in the USA for $57 with shipping for the 144cc . Scott Sent from Yahoo Mail for iPad On Jan 10, 2016, 7:49:36 AM,
      Scott Kirn
      Jan 11
      #10169
       
      10168

      Re: engine rebuild

      They are available in kits here in the USA for $57 with shipping for the 144cc . Scott Sent from Yahoo Mail for iPad On Jan 10, 2016, 7:49:36 AM,
      Scott Kirn
      Jan 11
      #10168
       
      10167

      Re: Lifa 200cc engine

      Hi,in order to swap the engine of your 1974 CB125S there is some things you need to consider:1- your bike is points ignition with a  6volt charging system
      Robyn Williams
      Jan 11
      #10167
       
      View First Topic Go to View Last Topic
      Loading 1 - 15 of total 10,181 messages