Loading ...
Sorry, an error occurred while loading the content.
 

Re: [BUG] Chris's ES1A Rebuild

Expand Messages
  • cfamalette
    It s in. stayed lined up! Still have an error... When powered on the Red Light on the Continous Dosage button flashes like it s in program mode. The key
    Message 1 of 15 , May 12, 2009
      It's in. stayed lined up!

      Still have an error...
      When powered on the Red Light on the Continous Dosage button flashes like it's in program mode. The key switch and toggle switch have been completely removed. I have the ribbon cable out and all looks good.

      Any ideas?

      Chris



      --- In BUG-is-Bunn@yahoogroups.com, Tim Fischer <fischertim@...> wrote:
      >
      > Right, that sounds like the 'new-style' jet line-up. That is the one I ended up going with as well, second time around.
      >
      >
      >
      >
      > ________________________________
      > From: Ray Brown <brown.ray.e@...>
      > To: BUG-is-Bunn@yahoogroups.com
      > Sent: Tuesday, May 12, 2009 5:36:58 PM
      > Subject: RE: [BUG] Chris's ES1A Rebuild
      >
      >
      >
      >
      >
      > My jet line up fit in nicely and just sits there.. It is not held in place
      > by a spring, just the o-ring on the jet sliding in to the top of the hex
      > holder. The screen is also just a pressure fit on the top of the jet..
      >
      > I guess if you turned it upside down and beat on it. It might come loose..
      >
      > I just used my recently completed rebuild at an Event and put out about 60
      > Mochas with no trouble..
      >
      > From: BUG-is-Bunn@ yahoogroups. com [mailto:BUG-is-Bunn@ yahoogroups. com] On
      > Behalf Of Tim Fischer
      > Sent: Tuesday, May 12, 2009 2:16 PM
      > To: BUG-is-Bunn@ yahoogroups. com
      > Subject: Re: [BUG] Chris's ES1A Rebuild
      >
      > The M8 will thread into the grouphead. Whether or not you can keep the jet
      > line up in place with the short pin will be the next question.
      >
      > ____________ _________ _________ __
      > From: cfamalette <cfamalette@yahoo. com <mailto:cfamalette% 40yahoo.com> >
      > To: BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com>
      > Sent: Tuesday, May 12, 2009 3:55:23 PM
      > Subject: [BUG] Chris's ES1A Rebuild
      >
      > Parts just came in!!!
      > I am not near the machine right now and have a question. Will the short pin
      > M6 / M8 thread into the grouphead?
      >
      > Hopfully will have a working shot tonight. Maybe even post a video......
      >
      > Chris
      >
      > [Non-text portions of this message have been removed]
      >
      > [Non-text portions of this message have been removed]
      >
      >
      >
      >
      >
      >
      >
      > [Non-text portions of this message have been removed]
      >
    • Robert Harmon
      What did you do with the wire leads you removed from the keyed-switch & toggle-switch? Tex
      Message 2 of 15 , May 12, 2009
        What did you do with the wire leads you removed from the keyed-switch & toggle-switch?

        Tex

        --- In BUG-is-Bunn@yahoogroups.com, "cfamalette" <cfamalette@...> wrote:
        >
        > It's in. stayed lined up!
        >
        > Still have an error...
        > When powered on the Red Light on the Continous Dosage button flashes like it's in program mode. The key switch and toggle switch have been completely removed. I have the ribbon cable out and all looks good.
        >
        > Any ideas?
        >
        > Chris
        >
        >
        >
        > --- In BUG-is-Bunn@yahoogroups.com, Tim Fischer <fischertim@> wrote:
        > >
        > > Right, that sounds like the 'new-style' jet line-up. That is the one I ended up going with as well, second time around.
        > >
        > >
        > >
        > >
        > > ________________________________
        > > From: Ray Brown <brown.ray.e@>
        > > To: BUG-is-Bunn@yahoogroups.com
        > > Sent: Tuesday, May 12, 2009 5:36:58 PM
        > > Subject: RE: [BUG] Chris's ES1A Rebuild
        > >
        > >
        > >
        > >
        > >
        > > My jet line up fit in nicely and just sits there.. It is not held in place
        > > by a spring, just the o-ring on the jet sliding in to the top of the hex
        > > holder. The screen is also just a pressure fit on the top of the jet..
        > >
        > > I guess if you turned it upside down and beat on it. It might come loose..
        > >
        > > I just used my recently completed rebuild at an Event and put out about 60
        > > Mochas with no trouble..
        > >
        > > From: BUG-is-Bunn@ yahoogroups. com [mailto:BUG-is-Bunn@ yahoogroups. com] On
        > > Behalf Of Tim Fischer
        > > Sent: Tuesday, May 12, 2009 2:16 PM
        > > To: BUG-is-Bunn@ yahoogroups. com
        > > Subject: Re: [BUG] Chris's ES1A Rebuild
        > >
        > > The M8 will thread into the grouphead. Whether or not you can keep the jet
        > > line up in place with the short pin will be the next question.
        > >
        > > ____________ _________ _________ __
        > > From: cfamalette <cfamalette@yahoo. com <mailto:cfamalette% 40yahoo.com> >
        > > To: BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com>
        > > Sent: Tuesday, May 12, 2009 3:55:23 PM
        > > Subject: [BUG] Chris's ES1A Rebuild
        > >
        > > Parts just came in!!!
        > > I am not near the machine right now and have a question. Will the short pin
        > > M6 / M8 thread into the grouphead?
        > >
        > > Hopfully will have a working shot tonight. Maybe even post a video......
        > >
        > > Chris
        > >
        > > [Non-text portions of this message have been removed]
        > >
        > > [Non-text portions of this message have been removed]
        > >
        > >
        > >
        > >
        > >
        > >
        > >
        > > [Non-text portions of this message have been removed]
        > >
        >
      • Paul Albert Acosta
        Chris, The continuous dose button will also blink when there is an error in the configuration of the membrane buttons or a defective dosing printed circuit
        Message 3 of 15 , May 13, 2009
          Chris,



          The continuous dose button will also blink when there is an error in the configuration of the membrane buttons or a defective dosing printed circuit board behind the membrane buttons. The flashing is telling you that there is an error. The ribbon cable must be checked and plugged in at all times during operation. The light will not blink unless the ribbon cable is plugged in. The ribbon cable provides the power to the buttons? How can you have the ribbon cable out and all looks good?

          Regards


          Paul Albert Acosta





          .







          _________________________________________________________________
          HotmailĀ® goes with you.
          http://windowslive.com/Tutorial/Hotmail/Mobile?ocid=TXT_TAGLM_WL_HM_Tutorial_Mobile1_052009

          [Non-text portions of this message have been removed]
        • cfamalette
          The key switch was broken, so i decided to move the toggle to the keyhole and realized the toggle was much smaller so I have not installed it yet!
          Message 4 of 15 , May 13, 2009
            The key switch was broken, so i decided to move the toggle to the keyhole and realized the toggle was much smaller so I have not installed it yet!


            --- In BUG-is-Bunn@yahoogroups.com, "Robert Harmon" <Texas_Coffee@...> wrote:
            >
            > What did you do with the wire leads you removed from the keyed-switch & toggle-switch?
            >
            > Tex
            >
            > --- In BUG-is-Bunn@yahoogroups.com, "cfamalette" <cfamalette@> wrote:
            > >
            > > It's in. stayed lined up!
            > >
            > > Still have an error...
            > > When powered on the Red Light on the Continous Dosage button flashes like it's in program mode. The key switch and toggle switch have been completely removed. I have the ribbon cable out and all looks good.
            > >
            > > Any ideas?
            > >
            > > Chris
            > >
            > >
            > >
            > > --- In BUG-is-Bunn@yahoogroups.com, Tim Fischer <fischertim@> wrote:
            > > >
            > > > Right, that sounds like the 'new-style' jet line-up. That is the one I ended up going with as well, second time around.
            > > >
            > > >
            > > >
            > > >
            > > > ________________________________
            > > > From: Ray Brown <brown.ray.e@>
            > > > To: BUG-is-Bunn@yahoogroups.com
            > > > Sent: Tuesday, May 12, 2009 5:36:58 PM
            > > > Subject: RE: [BUG] Chris's ES1A Rebuild
            > > >
            > > >
            > > >
            > > >
            > > >
            > > > My jet line up fit in nicely and just sits there.. It is not held in place
            > > > by a spring, just the o-ring on the jet sliding in to the top of the hex
            > > > holder. The screen is also just a pressure fit on the top of the jet..
            > > >
            > > > I guess if you turned it upside down and beat on it. It might come loose..
            > > >
            > > > I just used my recently completed rebuild at an Event and put out about 60
            > > > Mochas with no trouble..
            > > >
            > > > From: BUG-is-Bunn@ yahoogroups. com [mailto:BUG-is-Bunn@ yahoogroups. com] On
            > > > Behalf Of Tim Fischer
            > > > Sent: Tuesday, May 12, 2009 2:16 PM
            > > > To: BUG-is-Bunn@ yahoogroups. com
            > > > Subject: Re: [BUG] Chris's ES1A Rebuild
            > > >
            > > > The M8 will thread into the grouphead. Whether or not you can keep the jet
            > > > line up in place with the short pin will be the next question.
            > > >
            > > > ____________ _________ _________ __
            > > > From: cfamalette <cfamalette@yahoo. com <mailto:cfamalette% 40yahoo.com> >
            > > > To: BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com>
            > > > Sent: Tuesday, May 12, 2009 3:55:23 PM
            > > > Subject: [BUG] Chris's ES1A Rebuild
            > > >
            > > > Parts just came in!!!
            > > > I am not near the machine right now and have a question. Will the short pin
            > > > M6 / M8 thread into the grouphead?
            > > >
            > > > Hopfully will have a working shot tonight. Maybe even post a video......
            > > >
            > > > Chris
            > > >
            > > > [Non-text portions of this message have been removed]
            > > >
            > > > [Non-text portions of this message have been removed]
            > > >
            > > >
            > > >
            > > >
            > > >
            > > >
            > > >
            > > > [Non-text portions of this message have been removed]
            > > >
            > >
            >
          • Ray Brown
            Doesn t quite answer his question as to what did you do with the ends of the wires?? Are they twisted together, or kept apart?? From:
            Message 5 of 15 , May 13, 2009
              Doesn't quite answer his question as to what did you do with the ends of the
              wires?? Are they twisted together, or kept apart??



              From: BUG-is-Bunn@yahoogroups.com [mailto:BUG-is-Bunn@yahoogroups.com] On
              Behalf Of cfamalette
              Sent: Wednesday, May 13, 2009 12:20 PM
              To: BUG-is-Bunn@yahoogroups.com
              Subject: Re: [BUG] Chris's ES1A Rebuild








              The key switch was broken, so i decided to move the toggle to the keyhole
              and realized the toggle was much smaller so I have not installed it yet!

              --- In BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com> ,
              "Robert Harmon" <Texas_Coffee@...> wrote:
              >
              > What did you do with the wire leads you removed from the keyed-switch &
              toggle-switch?
              >
              > Tex
              >
              > --- In BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com>
              , "cfamalette" <cfamalette@> wrote:
              > >
              > > It's in. stayed lined up!
              > >
              > > Still have an error...
              > > When powered on the Red Light on the Continous Dosage button flashes
              like it's in program mode. The key switch and toggle switch have been
              completely removed. I have the ribbon cable out and all looks good.
              > >
              > > Any ideas?
              > >
              > > Chris
              > >
              > >
              > >
              > > --- In BUG-is-Bunn@yahoogroups.com
              <mailto:BUG-is-Bunn%40yahoogroups.com> , Tim Fischer <fischertim@> wrote:
              > > >
              > > > Right, that sounds like the 'new-style' jet line-up. That is the one I
              ended up going with as well, second time around.
              > > >
              > > >
              > > >
              > > >
              > > > ________________________________
              > > > From: Ray Brown <brown.ray.e@>
              > > > To: BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com>

              > > > Sent: Tuesday, May 12, 2009 5:36:58 PM
              > > > Subject: RE: [BUG] Chris's ES1A Rebuild
              > > >
              > > >
              > > >
              > > >
              > > >
              > > > My jet line up fit in nicely and just sits there.. It is not held in
              place
              > > > by a spring, just the o-ring on the jet sliding in to the top of the
              hex
              > > > holder. The screen is also just a pressure fit on the top of the jet..
              > > >
              > > > I guess if you turned it upside down and beat on it. It might come
              loose..
              > > >
              > > > I just used my recently completed rebuild at an Event and put out
              about 60
              > > > Mochas with no trouble..
              > > >
              > > > From: BUG-is-Bunn@ yahoogroups. com [mailto:BUG-is-Bunn@ yahoogroups.
              com] On
              > > > Behalf Of Tim Fischer
              > > > Sent: Tuesday, May 12, 2009 2:16 PM
              > > > To: BUG-is-Bunn@ yahoogroups. com
              > > > Subject: Re: [BUG] Chris's ES1A Rebuild
              > > >
              > > > The M8 will thread into the grouphead. Whether or not you can keep the
              jet
              > > > line up in place with the short pin will be the next question.
              > > >
              > > > ____________ _________ _________ __
              > > > From: cfamalette <cfamalette@yahoo. com <mailto:cfamalette%
              40yahoo.com> >
              > > > To: BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog
              roups.com>
              > > > Sent: Tuesday, May 12, 2009 3:55:23 PM
              > > > Subject: [BUG] Chris's ES1A Rebuild
              > > >
              > > > Parts just came in!!!
              > > > I am not near the machine right now and have a question. Will the
              short pin
              > > > M6 / M8 thread into the grouphead?
              > > >
              > > > Hopfully will have a working shot tonight. Maybe even post a
              video......
              > > >
              > > > Chris
              > > >
              > > > [Non-text portions of this message have been removed]
              > > >
              > > > [Non-text portions of this message have been removed]
              > > >
              > > >
              > > >
              > > >
              > > >
              > > >
              > > >
              > > > [Non-text portions of this message have been removed]
              > > >
              > >
              >





              [Non-text portions of this message have been removed]
            • cfamalette
              How can you have the ribbon cable out and all looks good? Meaning I took the cable out and used a multimeter to check it. No opens found, I had continuity
              Message 6 of 15 , May 13, 2009
                "How can you have the ribbon cable out and all looks good?"
                Meaning I took the cable out and used a multimeter to check it. No opens found, I had continuity from connector to connector.

                --- In BUG-is-Bunn@yahoogroups.com, Paul Albert Acosta <paul_albert_acosta@...> wrote:
                >
                >
                > Chris,
                >
                >
                >
                > The continuous dose button will also blink when there is an error in the configuration of the membrane buttons or a defective dosing printed circuit board behind the membrane buttons. The flashing is telling you that there is an error. The ribbon cable must be checked and plugged in at all times during operation. The light will not blink unless the ribbon cable is plugged in. The ribbon cable provides the power to the buttons? How can you have the ribbon cable out and all looks good?
                >
                > Regards
                >
                >
                > Paul Albert Acosta
                >
                >
                >
                >
                >
                > .
                >
                >
                >
                >
                >
                >
                >
                > _________________________________________________________________
                > HotmailĀ® goes with you.
                > http://windowslive.com/Tutorial/Hotmail/Mobile?ocid=TXT_TAGLM_WL_HM_Tutorial_Mobile1_052009
                >
                > [Non-text portions of this message have been removed]
                >
              • cfamalette
                Appears to be working now. Water level issues. Could not clear the fault. Testing shots soon!
                Message 7 of 15 , May 13, 2009
                  Appears to be working now. Water level issues. Could not clear the fault. Testing shots soon!



                  --- In BUG-is-Bunn@yahoogroups.com, Paul Albert Acosta <paul_albert_acosta@...> wrote:
                  >
                  >
                  > Chris,
                  >
                  >
                  >
                  > The continuous dose button will also blink when there is an error in the configuration of the membrane buttons or a defective dosing printed circuit board behind the membrane buttons. The flashing is telling you that there is an error. The ribbon cable must be checked and plugged in at all times during operation. The light will not blink unless the ribbon cable is plugged in. The ribbon cable provides the power to the buttons? How can you have the ribbon cable out and all looks good?
                  >
                  > Regards
                  >
                  >
                  > Paul Albert Acosta
                  >
                  >
                  >
                  >
                  >
                  > .
                  >
                  >
                  >
                  >
                  >
                  >
                  >
                  > _________________________________________________________________
                  > HotmailĀ® goes with you.
                  > http://windowslive.com/Tutorial/Hotmail/Mobile?ocid=TXT_TAGLM_WL_HM_Tutorial_Mobile1_052009
                  >
                  > [Non-text portions of this message have been removed]
                  >
                • cfamalette
                  My machine is a M8 Long pin as well. Ordering another part! Chris
                  Message 8 of 15 , May 13, 2009
                    My machine is a M8 Long pin as well.
                    Ordering another part!


                    Chris

                    --- In BUG-is-Bunn@yahoogroups.com, "Ray Brown" <brown.ray.e@...> wrote:
                    >
                    > My jet line up fit in nicely and just sits there.. It is not held in place
                    > by a spring, just the o-ring on the jet sliding in to the top of the hex
                    > holder. The screen is also just a pressure fit on the top of the jet..
                    >
                    >
                    >
                    > I guess if you turned it upside down and beat on it. It might come loose..
                    >
                    >
                    >
                    > I just used my recently completed rebuild at an Event and put out about 60
                    > Mochas with no trouble..
                    >
                    >
                    >
                    >
                    >
                    > From: BUG-is-Bunn@yahoogroups.com [mailto:BUG-is-Bunn@yahoogroups.com] On
                    > Behalf Of Tim Fischer
                    > Sent: Tuesday, May 12, 2009 2:16 PM
                    > To: BUG-is-Bunn@yahoogroups.com
                    > Subject: Re: [BUG] Chris's ES1A Rebuild
                    >
                    >
                    >
                    >
                    >
                    >
                    >
                    >
                    > The M8 will thread into the grouphead. Whether or not you can keep the jet
                    > line up in place with the short pin will be the next question.
                    >
                    > ________________________________
                    > From: cfamalette <cfamalette@... <mailto:cfamalette%40yahoo.com> >
                    > To: BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com>
                    > Sent: Tuesday, May 12, 2009 3:55:23 PM
                    > Subject: [BUG] Chris's ES1A Rebuild
                    >
                    > Parts just came in!!!
                    > I am not near the machine right now and have a question. Will the short pin
                    > M6 / M8 thread into the grouphead?
                    >
                    > Hopfully will have a working shot tonight. Maybe even post a video......
                    >
                    > Chris
                    >
                    > [Non-text portions of this message have been removed]
                    >
                    >
                    >
                    >
                    >
                    > [Non-text portions of this message have been removed]
                    >
                  • Ray Brown
                    Chris. If you ordered the MA_25 Tall 8MM Upper Group Valve Pin from EspressoParts.. that is the wrong one.. It says it is tall, but it is actually shorter than
                    Message 9 of 15 , May 13, 2009
                      Chris.



                      If you ordered the MA_25 Tall 8MM Upper Group Valve Pin from EspressoParts..
                      that is the wrong one.. It says it is tall, but it is actually shorter than
                      the Item # 50147 Short Pin M8 from CafeParts. That is assuming you are doing
                      the jet line-up and not the new injector configuration.



                      I believe Tim went to the Injector line-up, as I did, and it seems to work
                      great and is easier to put together. no spring to worry about .



                      Have fun..



                      Ray



                      From: BUG-is-Bunn@yahoogroups.com [mailto:BUG-is-Bunn@yahoogroups.com] On
                      Behalf Of cfamalette
                      Sent: Wednesday, May 13, 2009 6:15 PM
                      To: BUG-is-Bunn@yahoogroups.com
                      Subject: Re: [BUG] Chris's ES1A Rebuild








                      My machine is a M8 Long pin as well.
                      Ordering another part!

                      Chris

                      --- In BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com> ,
                      "Ray Brown" <brown.ray.e@...> wrote:
                      >
                      > My jet line up fit in nicely and just sits there.. It is not held in place
                      > by a spring, just the o-ring on the jet sliding in to the top of the hex
                      > holder. The screen is also just a pressure fit on the top of the jet..
                      >
                      >
                      >
                      > I guess if you turned it upside down and beat on it. It might come loose..
                      >
                      >
                      >
                      > I just used my recently completed rebuild at an Event and put out about 60
                      > Mochas with no trouble..
                      >
                      >
                      >
                      >
                      >
                      > From: BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com>
                      [mailto:BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com> ]
                      On
                      > Behalf Of Tim Fischer
                      > Sent: Tuesday, May 12, 2009 2:16 PM
                      > To: BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com>
                      > Subject: Re: [BUG] Chris's ES1A Rebuild
                      >
                      >
                      >
                      >
                      >
                      >
                      >
                      >
                      > The M8 will thread into the grouphead. Whether or not you can keep the jet
                      > line up in place with the short pin will be the next question.
                      >
                      > ________________________________
                      > From: cfamalette <cfamalette@... <mailto:cfamalette%40yahoo.com> >
                      > To: BUG-is-Bunn@yahoogroups.com <mailto:BUG-is-Bunn%40yahoogroups.com>
                      <mailto:BUG-is-Bunn%40yahoogroups.com>
                      > Sent: Tuesday, May 12, 2009 3:55:23 PM
                      > Subject: [BUG] Chris's ES1A Rebuild
                      >
                      > Parts just came in!!!
                      > I am not near the machine right now and have a question. Will the short
                      pin
                      > M6 / M8 thread into the grouphead?
                      >
                      > Hopfully will have a working shot tonight. Maybe even post a video......
                      >
                      > Chris
                      >
                      > [Non-text portions of this message have been removed]
                      >
                      >
                      >
                      >
                      >
                      > [Non-text portions of this message have been removed]
                      >





                      [Non-text portions of this message have been removed]
                    • Tim Fischer
                      Yep, that is the gist of it... The first MA_25 Tall 8MM I got was actually a 6mm. I re-ordered and was sent an 8MM that I was told would be the long one
                      Message 10 of 15 , May 13, 2009
                        Yep, that is the gist of it... The first MA_25 Tall 8MM I got was actually a 6mm. I re-ordered and was sent an 8MM that I was told would be the long one based on some measurements I supplied to the vendor. As stated in a previous post, the spring didn't appear it was long enough to keep everything together so I have to assume either I got the wrong pin or the wrong spring... Someone else had success with the new injector line-up so I re-ordered that entire line-up and that is what I'm currently using. Eventually I'll have enough spares to build another ES-1A from scratch! :-)




                        ________________________________
                        From: Ray Brown <brown.ray.e@...>
                        To: BUG-is-Bunn@yahoogroups.com
                        Sent: Wednesday, May 13, 2009 9:15:44 PM
                        Subject: RE: [BUG] Chris's ES1A Rebuild





                        Chris.

                        If you ordered the MA_25 Tall 8MM Upper Group Valve Pin from EspressoParts. .
                        that is the wrong one.. It says it is tall, but it is actually shorter than
                        the Item # 50147 Short Pin M8 from CafeParts. That is assuming you are doing
                        the jet line-up and not the new injector configuration.

                        I believe Tim went to the Injector line-up, as I did, and it seems to work
                        great and is easier to put together. no spring to worry about .

                        Have fun..

                        Ray

                        From: BUG-is-Bunn@ yahoogroups. com [mailto:BUG-is-Bunn@ yahoogroups. com] On
                        Behalf Of cfamalette
                        Sent: Wednesday, May 13, 2009 6:15 PM
                        To: BUG-is-Bunn@ yahoogroups. com
                        Subject: Re: [BUG] Chris's ES1A Rebuild

                        My machine is a M8 Long pin as well.
                        Ordering another part!

                        Chris

                        --- In BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com> ,
                        "Ray Brown" <brown.ray.e@ ...> wrote:
                        >
                        > My jet line up fit in nicely and just sits there.. It is not held in place
                        > by a spring, just the o-ring on the jet sliding in to the top of the hex
                        > holder. The screen is also just a pressure fit on the top of the jet..
                        >
                        >
                        >
                        > I guess if you turned it upside down and beat on it. It might come loose..
                        >
                        >
                        >
                        > I just used my recently completed rebuild at an Event and put out about 60
                        > Mochas with no trouble..
                        >
                        >
                        >
                        >
                        >
                        > From: BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com>
                        [mailto:BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com> ]
                        On
                        > Behalf Of Tim Fischer
                        > Sent: Tuesday, May 12, 2009 2:16 PM
                        > To: BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com>
                        > Subject: Re: [BUG] Chris's ES1A Rebuild
                        >
                        >
                        >
                        >
                        >
                        >
                        >
                        >
                        > The M8 will thread into the grouphead. Whether or not you can keep the jet
                        > line up in place with the short pin will be the next question.
                        >
                        > ____________ _________ _________ __
                        > From: cfamalette <cfamalette@ ... <mailto:cfamalette% 40yahoo.com> >
                        > To: BUG-is-Bunn@ yahoogroups. com <mailto:BUG- is-Bunn%40yahoog roups.com>
                        <mailto:BUG- is-Bunn%40yahoog roups.com>
                        > Sent: Tuesday, May 12, 2009 3:55:23 PM
                        > Subject: [BUG] Chris's ES1A Rebuild
                        >
                        > Parts just came in!!!
                        > I am not near the machine right now and have a question. Will the short
                        pin
                        > M6 / M8 thread into the grouphead?
                        >
                        > Hopfully will have a working shot tonight. Maybe even post a video......
                        >
                        > Chris
                        >
                        > [Non-text portions of this message have been removed]
                        >
                        >
                        >
                        >
                        >
                        > [Non-text portions of this message have been removed]
                        >

                        [Non-text portions of this message have been removed]







                        [Non-text portions of this message have been removed]
                      Your message has been successfully submitted and would be delivered to recipients shortly.