Loading ...
Sorry, an error occurred while loading the content.

Re: [BPQ32] multiple nics

Expand Messages
  • Mark Harloff
    I tried all three modes (Bcast, Multi and target). I did not try the RLI varient. I ll try that and let you know. - Mark
    Message 1 of 5 , Nov 24, 2008
    • 0 Attachment
      I tried all three modes (Bcast, Multi and
      target). I did not try the RLI varient.
      I'll try that and let you know.

      - Mark


      John Wiseman wrote:
      >
      >
      > Remember there are two varients of BPQEther - Mine and W0RLI's. I don't
      > know which one Flexnet uses. And also check whether you need to use the
      > Broadcast, Multicast or a specific targer address for Flexnet.
      >
      > John
      >
      >
      > -----Original Message-----
      > *From:* BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com]*On
      > Behalf Of *Mark Harloff
      > *Sent:* 24 November 2008 20:38
      > *To:* BPQ32@yahoogroups.com
      > *Subject:* Re: [BPQ32] multiple nics
      >
      > Thanks John. I tried BPQEther but for some
      > reason it seemed to communicate only in one
      > direction. I ran wireshark and could see packets
      > going in and coming out but nothing was
      > registering on the FlexNet machine. I am
      > thinking it was a problem within the FlexNet
      > ether driver. I'll look into it when I have more
      > time.
      >
      > 73, Mark
      >
      > John Wiseman wrote:
      > >
      > >
      > > Mark,
      > >
      > > Yes. If using the BPQEther driver, you specify which adapter you
      > want to
      > > use in the bpqether.cfg file. If using axip, it will use the adapter
      > > that has the best route to the target IP address.
      > >
      > > 73,
      > > John
      > >
      > >
      > > -----Original Message-----
      > > *From:* BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com>
      > [mailto:BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com>] *On
      > > Behalf Of *Mark Harloff
      > > *Sent:* 23 November 2008 13:08
      > > *To:* BPQ32 SIG
      > > *Subject:* [BPQ32] multiple nics
      > >
      > >
      > > I am currently have two nics installed in a
      > > machine running XP Pro. One is currently used to
      > > connect the machine to a LAN router. The second
      > > one is going to be connected to a second machine
      > > running FlexNet. I do not want to go through the
      > > LAN router to connect the two machines but
      > > rather just link them 'directly' using a nic at
      > > each end.
      > >
      > > Does anyone know if it's possible to have BPQ32
      > > specifically use a second nic as opposed to the
      > > first of two installed in a machine running XP Pro ?
      > >
      > > - Mark K2CAN
      > >
      > >
      > >
      > >
      > > ----------------------------------------------------------
      > >
      > >
      > > No virus found in this incoming message.
      > > Checked by AVG - http://www.avg.com <http://www.avg.com>
      > > Version: 8.0.175 / Virus Database: 270.9.10/1810 - Release Date:
      > 11/24/2008 2:36 PM
      > >
      >
      >
      >
      >
      > ------------------------------------------------------------------------
      >
      >
      > No virus found in this incoming message.
      > Checked by AVG - http://www.avg.com
      > Version: 8.0.175 / Virus Database: 270.9.10/1810 - Release Date: 11/24/2008 2:36 PM
      >
    Your message has been successfully submitted and would be delivered to recipients shortly.