Loading ...
Sorry, an error occurred while loading the content.

RE: [BPQ32] Re: Tsthwin and bpq32

Expand Messages
  • John Wiseman
    Can you send me your bpq32.cfg and I ll see if I can see what the problem is. 73, John _____ From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On
    Message 1 of 14 , May 14, 2013
    • 0 Attachment
      Can you send me your bpq32.cfg and I'll see if I can see what the problem is.
       
      73, John


      From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of nl2prc
      Sent: 13 May 2013 21:48
      To: BPQ32@yahoogroups.com
      Subject: [BPQ32] Re: Tsthwin and bpq32

       

      This is the map i use

      MAP NL9DHR 192.168.23.5 UDP 93 B

      And is workin oke i think

      Also unproto to NL3DHR is workin this is mij home bbs

      But i'm having problems because the bbs can't be seen directly

      i have a problem to digi it via node

      What i need is this

      NL2DHR to NL3DHR via NL9DHR ctl UI

      No matter what i doe i get

      nl2dhr to nl3dhr ctl UI

      where do i go wrang

      And on the bpq monitor i only see nl2dhr on the loopback port

      Greetings ascal

      --- In BPQ32@yahoogroups.com, "John Wiseman" <john.wiseman@...> wrote:

      >
      > UNPROTO does work on
      AXUDP ports. You must have a MAP entry for the call the
      > packet is being
      sent to, or the code won't konw what IP address to send it
      > to.
      >
      > 73, John
      >
      > _____
      >
      > From:
      href="mailto:BPQ32%40yahoogroups.com">BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of
      > nl2prc
      > Sent: 13 May 2013 19:36
      > To:
      href="mailto:BPQ32%40yahoogroups.com">BPQ32@yahoogroups.com
      > Subject:
      [BPQ32] Re: Tsthwin and bpq32
      >
      >
      >
      >
      > Here
      another problem command UNPROTO is not workin on a axudp port
      > And there
      is where in want to digi it via another node
      >
      > --- In
      href="mailto:BPQ32%40yahoogroups.com">BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com> , "John
      > Wiseman"
      <john.wiseman@> wrote:
      > >
      > > UI frames should be sent
      to the path specified in the UNPROTO parameter of
      > > the PORT
      config.
      > >
      > > 73, John
      > >
      > > _____
      > >
      > > From:
      href="mailto:BPQ32%40yahoogroups.com">BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com>
      > [mailto:
      href="mailto:BPQ32%40yahoogroups.com">BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com> ] On Behalf
      > Of
      > >
      nl2prc
      > > Sent: 13 May 2013 14:59
      > > To:
      href="mailto:BPQ32%40yahoogroups.com">BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com>
      > > Subject: [BPQ32] Tsthwin
      and bpq32
      > >
      > >
      > >
      > >
      > >
      Hi all
      > >
      > > I'm running tsthwin and bpq32 however i can't
      digi my UI frames to another
      > > node zo that i can use the
      ulist
      > >
      > > Is there a way of doing this
      > >
      >

    • nl2prc
      This is my bpq32.cfgNL3DHR is using LINUX an NL9DHR is running on Xnet node software 1.36 ... comment CONFIGURATION FILE FOR BPQ32: G8BPQ SWITCH SOFTWARE
      Message 2 of 14 , May 14, 2013
      • 0 Attachment
        This is my bpq32.cfg
        NL3DHR is using LINUX an NL9DHR is running on Xnet node software 1.36

        ---------------------------------------------------------------------------------------------------------------
        /* This begins a multi-line comment

        CONFIGURATION FILE FOR BPQ32: G8BPQ SWITCH SOFTWARE

        Includes 1 AX/IP/UDP Port and 2 BPQKISS TNC Ports.


        \Examples\Large_without_AGWPE

        Substitute your amateur call for every occurance 'MYCALL'. Make appropriate
        changes to NODEALIAS, APPLnALLIAS's, IDMSG, BTEXT, INFOMSG and CTEXT to suit
        your installation.

        */ This ends a multi-line comment

        LOCATOR=JO22JW
        ;See LOCATOR details at:
        ;http://www.cantab.net/users/john.wiseman/Documents/BPQNodeMap.htm

        ;PASSWORD=ABCDEFGHILKLMNOPQRSTUVWXY
        ; SYSOP Passord - See http://www.cantab.net/users/john.wiseman/Documents/Node%20SYSOP.html

        NODECALL=NL4DHR ; Node callsign
        NODEALIAS=NLDHR ; Node alias (6 characters max)
        IDMSG: ; UI broadcast text from NODECALL to fixed dest ID
        NL4DHR TEST NODE
        *** ; Denotes end of IDMSG text

        /*
        The BTEXT below contains an APRS location specification. Search the internet
        for "APRS Protocol Specification" for details on the format.  If you do not
        care to do this, it would be best to replace the line by simple non APRS
        text rather than transmit incorrect data which may find it's way via APRS
        IGates to FINDU.COM.
        */

        BTEXT: ; UI broadcast text from BCALL to destination UNPROTO=
        NL2DHR
        *** ; Denotes end of BTEXT text
        INFOMSG: ; The INFO command text follows:
        Test node Den Helder JO22JW
        *** ; Denotes end of INFOMSG text
        CTEXT: ; The CTEXT text follows:
        NLDHR:NL4DHR} BBS CONNECT BYE INFO NODES ROUTES PORTS USERS MHEARD
        Test Node Den Helder
        *** ; Denotes end of CTEXT text
        FULL_CTEXT=0 ; 0=send CTEXT to L2 connects to NODEALIAS only
        ; 1=send CTEXT to all connectees

        ; Network System Parameters:

        OBSINIT=6 ; Initial obsolescence set when a node is included
        ; in a received nodes broadcast. This value is then
        ; decremented by 1 every NODESINTERVAL.
        OBSMIN=4 ; When the obsolescence of a node falls below this
        ; value that node's information is not included in
        ; a subsequent nodes broadcast.
        NODESINTERVAL=10 ; Nodes broadcast interval in minutes
        IDINTERVAL=60 ; 'IDMSG' UI broadcast interval in minutes, 0=OFF
        BTINTERVAL=60 ; The BTEXT broadcast interval in minutes, 0=OFF
        L3TIMETOLIVE=25 ; Max L3 hops
        L4RETRIES=3 ; Level 4 retry count
        L4TIMEOUT=60 ; Level 4 timeout in seconds s/b > FRACK x RETRIES
        L4DELAY=10 ; Level 4 delayed ack timer in seconds
        L4WINDOW=4 ; Level 4 window size
        MAXLINKS=63 ; Max level 2 links
        MAXNODES=128 ; Max nodes in nodes table
        MAXROUTES=64 ; Max adjacent nodes
        MAXCIRCUITS=128 ; Max L4 circuits
        MINQUAL=168 ; Minimum quality to add to nodes table
        ; INP3 Routing is experimental.  The two parms which follow will be ignored
        ; unless activated in the ROUTES: section.
        MAXHOPS=4 ; INP3 hop limit to add to tables
        MAXRTT=90 ; INP3 max RTT in seconds
        BUFFERS=255 ; Packet buffers - 255 means allocate as many as
        ; possible, normally about 130, depending upon other
        ; table sizes.


        ; TNC default parameters:

        PACLEN=236 ; Max packet size (236 max for net/rom)

         /*
        PACLEN is a problem! The ideal size depends on the link(s) over which a packet
        will be sent. For a session involving another node, we have no idea what is at
        the far end. Ideally each node should have the capability to combine and then
        refragment messages to suit each link segment - maybe when there are more BPQ
        nodes about than 'other' ones, I'll do it. When the node is accessed directly,
        things are a bit easier, as we know at least something about the link. So,
        currently there are two PACLEN params, one here and one in the PORTS section.
        This one is used to set the initial value for sessions via other nodes and for
        sessions initiated from here. The other is used for incoming direct (Level 2)
        sessions. In all cases the TNC PACLEN command can be used to override the
        defaults.
         */

        ; Level 2 Parameters:

        ; T1 (FRACK), T2 (RESPTIME) and N2 (RETRIES) are now in the PORTS section

        T3=120 ; Link validation timer in seconds
        IDLETIME=720 ; Idle link shutdown timer in seconds

        ; Configuration Options:

        AUTOSAVE=1 ; Saves BPQNODES.dat upon program exit
        BBS=1 ; 1 = BBS support included, 0 = No BBS support
        NODE=1 ; Include switch support
        HIDENODES=0 ; If set to 1, nodes beginning with a #
        ; require a 'N *' command to be displayed.

        ; The *** LINKED command is intended for use by gateway software, and concern
        ; has been expressed that it could be misused. It is recommended that it be
        ; disabled (=N) if unneeded.

        ENABLE_LINKED=A ; Controls processing of *** LINKED command
        ; Y = allows unrestricted use
        ; A = allows use by application program
        ; N = disabled

        ; Port Definitions:

        ; AX/IP/UDP port definition.

        PORT
         PORTNUM=1 ; Optional but sets port number if stated
         ID=AX/IP/UDP ; Displayed by PORTS command
         TYPE=EXTERNAL ; Calls an external module
         DLLNAME=BPQAXIP.DLL ; Uses BPQAXIP.DLL
         QUALITY=255 ; Quality factor applied to node broadcasts heard on
        ; this port, unless overridden by a locked route
        ; entry. Setting to 0 stops node broadcasts
         MINQUAL=168 ; Entries in the nodes table with qualities greater or
        ; equal to MINQUAL will be sent on this port. A value
        ; of 0 sends everything.
         MAXFRAME=7 ; Max outstanding frames (1 thru 7)
         FRACK=3000 ; Level 2 timout in milliseconds
         RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
         RETRIES=5 ; Level 2 maximum retry value
         PACLEN=236 ; Max = 236
         CONFIG ; BPQAXIP.cfg has been deprecated.  Instead the AXIP
        ; configuration occurs here:
        ; UNPROTO=NL3DHR NL9DHR
        ; DIGIFLAG=1
        ; DIGIPORT=1,2
         MHEARD ;Opens AXIP MHEARD window
         UDP 93 ;Listens for UDP packets on this UDP port number

        ; You may listen on additional port numbers if desired:
        ; UDP 10094 ;Listens for UDP packets on this UDP port number

        ; Starting with bpqaxip.dll version 1.14.1.1 the default behavior is to not
        ; add information to BPQ32's nodes table for AX/IP/UDP nodes which are not
        ; explicitly listed in the bpqaxip.cfg file.  The default behavior can be
        ; modified with these commands:
        ; DONTCHECKSOURCECALL ;This option allows entries in the NODES table from
        ;stations sending you nodes broadcasts without the
        ;corresponding node being configured in bpqaxip.cfg. 
         AUTOADDMAP ;This option automatically adds the node call and
        ;address of a node for which you do not have a
        ;pre-arranged fixed entry in bpqaxip.cfg.  If the 
        ;option DONTCHECKSOURCECALL is specified then the
        ;AUTOADDMAP option is ignored.

         BROADCAST NODES
        ; BROADCAST QST
        ; MAP NL3DHR 192.168 23 5 udp 93 B
        MAP NL9DHR 192.168.23.5 UDP 93 B
        ; MAP ZZ0ZZ z.example.org UDP 10093 B
        ; MAP CC8CC-5 208.77.188.166 UDP 10093 B
        ; MAP AA1AA-1 example.net UDP 10093 B
        ; If INP3 routing (experimental at this point) is utilized the 'B' command
        ; should not be included
        ; MAP BB9BB-6 example.com UDP 10093

        ; Steve Conrad, VE9SC, provides a service which displays a map of BPQMailChat
        ; nodes dynamically updated:  http://guardian.no-ip.org/bpqmap/ChatNetwork.htm
        ; To include your chat node on the map remove the ';' from the MAP DUMMY
        ; statement which follows.  The rest of the statement must remain exactly as
        ; shown.
        ; MAP DUMMY CHATMAP.G8BPQ.NET UDP 10090

        ; A keepalive may be needed if you have not properly configured your
        ; router to direct incoming UDP traffic to the specific machine on you
        ; LAN which is running BPQ32.  You should properly configure your router
        ; so that the keepalive is unneeded, as this ploy is not completely
        ; reliable!

        ; In the exceptional case where your ISP is dropping your incoming traffic
        ; testing has found that the keepalive might help 'keep the door open'.
        ; In the following example a keepalive packet is sent every 30 seconds:
        ; MAP AA1AA-1 example.net KEEPALIVE 30 UDP 10093 B

        ; An experimental TCP communication mode was added with the 2009/Aug/28 Beta
        ; release. The purpose is to circumvent router issues which are almost certain
        ; when 'your side', which we will call the client side, cannot control access
        ; to direct incoming UDP packets to your machine.  Instead you will originate
        ; a connection via TCP. TCP is a connected protocol, all routers should
        ; automatically set up the return path to your machine.

        ; An example would be your BPQ32 node, with a node call of MYCALL-5, on a
        ; laptop at a public access WiFI site. To connect to AA1AA-1 via this method
        ; you will need this entry in your MAP list (without the ; of course):
        ; MAP AA1AA-1 example.net TCP-Master 10093 B

        ; AA1AA-1 is the node call of the remote side, e.g. server side.  The server
        ; side must have the ability to program its router to direct incoming TCP
        ; traffic with the specified port number to the machine running BPQ32 Node
        ; AA1AA-1, just as it does for UDP.

        ; BPQ32 Node AA1AA-1 at URL=example.net would add the folllowing entry to its
        ; MAP list:
        ; MAP MYCALL-5 0.0.0.0 TCP-Slave 10093 B

        ; As a result AA1AA-1 will listen for TCP packets on port 10093 from MYCALL-5.
        ; When heard, a TCP connection will result over which AX.25 traffic will flow.
        ; The server side obtains the client side ip address when the connection
        ; request is received.

        ; As currently implemented the client side will have to make advance
        ; arrangements with the server side so that the correct MAP entries will be in
        ; effect, as well as to specify a unique TCP port number for each prearranged
        ; client.
        ENDPORT

        PORT
         PORTNUM=2 ; Optonal but sets port number if stated
         ID=LOOPBACK ; Defines the Loopback port
         TYPE=INTERNAL ; Loopback is an internal type
         MAXFRAME=7 ; Max outstanding frames (1 thru 7)
         FRACK=5000 ; Level 2 timout in milliseconds 
         RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
         RETRIES=5 ; Level 2 maximum retry value
         DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
         UNPROTO=NL3DHR NL9DHR ; DEFAULT UNPROTO ADDR
         DIGIFLAG=1
         DIGIPORT=2,1
        ENDPORT



        ; Radio port definitions.

        ; With the following definitions BPQ32 accesses the TNC directly.

        ; PORT
        ; PORTNUM=2 ; Optional but sets port number if stated
        ; ID=BPQ 1 ; Displayed by PORTS command
        ; TYPE=ASYNC ; Port is RS232 Com
        ; PROTOCOL=KISS ; TNC is used in KISS, JKISS or BPQKISS mode
        ; The KISSOPTIONS statement should not be included for KISS or JKISS tnc's.
        ; For this configuration the BPQKISS2 eprom, patched for no polling, channel A,
        ; is installed in a MFJ1270C. See ..\RelatedFiles\KissRoms\KissRoms.zip.
        ; KISSOPTIONS=CHECKSUM,ACKMODE ; Using BPQKISS eprom w/o polling
        ; FULLDUP=0 ; Only meaningful for KISS, JKISS or BPQKISS devices
        ; IOADDR=1 ; 1 = SERIAL PORT COM1 ETC.
        ; SPEED=9600 ; RS232 COM PORT SPEED
        ; CHANNEL=A ; A for single channel TNC, A or B for multichannel
        ; PERSIST=64 ; PERSIST=256/(# of transmitters-1)
        ; SLOTTIME=100 ; CMSA interval timer in milliseconds
        ; TXDELAY=300 ; Transmit keyup delay in milliseconds
        ; TXTAIL=30 ; TX key down, in milliseconds, at packet end
        ; QUALITY=192 ; Quality factor applied to node broadcasts heard on
        ; this port, unless overridden by a locked route
        ; entry. Setting to 0 stops node broadcasts
        ; MINQUAL=168 ; Entries in the nodes table with qualities greater or
        ; equal to MINQUAL will be sent on this port. A value
        ; of 0 sends everything.
        ; MAXFRAME=7 ; Max outstanding frames (1 thru 7)
        ; FRACK=5000 ; Level 2 timout in milliseconds
        ; RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
        ; RETRIES=5 ; Level 2 maximum retry value
        ; PACLEN=236 ; Default max packet length for this port
        ; UNPROTO=BPQP2 ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
        ; BCALL=NL4DHR ; BTEXT call. unstated defaults to APPL1CALL
        ; L3ONLY=0 ; 1=No user downlink connects on this port
        ; DIGIFLAG=0 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
        ; DIGIPORT=0 ; Port on which to send digi'd frames (0 = same port)
        ; USERS=0 ; Maximum number of L2 sessions, 0 = no limit
        ;ENDPORT

        ; PORT
        ; PORTNUM=3 ; Optional but sets port number if stated
        ; ID=BPQ 2 ; Displayed by PORTS command
        ; TYPE=ASYNC ; Port is RS232 Com
        ; PROTOCOL=KISS ; TNC is used in KISS, JKISS or BPQKISS mode
        ; The KISSOPTIONS statement should not be included for KISS or JKISS tnc's.
        ; For this configuration the BPQKISS2 eprom, patched for no polling, channel A,
        ; is installed in a MFJ1270C. See ..\RelatedFiles\KissRoms\KissRoms.zip.
        ; KISSOPTIONS=CHECKSUM,ACKMODE ; Using BPQKISS eprom w/o polling
        ; FULLDUP=0 ; Only meaningful for KISS, JKISS or BPQKISS devices
        ; IOADDR=3 ; 1 = SERIAL PORT COM1 ETC.
        ; SPEED=9600 ; SERIAL PORT SPEED, NOT RADIO DATA SPEED.
        ; CHANNEL=A ; A for single channel TNC, A or B for multichannel
        ; PERSIST=255 ; PERSIST=256/(# of transmitters-1)
        ; SLOTTIME=100 ; CMSA interval timer in milliseconds
        ; TXDELAY=300 ; Transmit keyup delay in milliseconds
        ; TXTAIL=30 ; TX key down, in milliseconds, at packet end
        ; In this application port 2 is used by UIView32 as an APRS digipeater thus
        ; nodes broadcasts are suppressed on this port by setting QUALITY=0.
        ; QUALITY=0 ; Quality factor applied to node broadcasts heard on
        ; this port, unless overridden by a locked route
        ; entry. Setting to 0 stops node broadcasts
        ; With QUALITY=0, the value of MINQUAL is irrelevant
        ; MINQUAL=168 ; Entries in the nodes table with qualities greater or
        ; equal to MINQUAL will be sent on this port. A value
        ; of 0 sends everything.
        ; MAXFRAME=7 ; Max outstanding frames (1 thru 7)
        ; In this application port 2 is used as an APRS digipeater thus the next two
        ; parms are set per the 'New Paradigm' recommendations:
        ; FRACK=5000 ; Level 2 timout in milliseconds
        ; RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
        ; RETRIES=5 ; Level 2 maximum retry value
        ; PACLEN=236 ; Default max packet length for this port
        ; UNPROTO=BPQP3 ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
        ; BCALL=NL4DHR ; BTEXT call. unstated defaults to APPL1CALL
        ; L3ONLY=0 ; 1=No user downlink connects on this port
        ; Digipeating to be done by UIView32 instead of BPQ32 for APRS applications:
        ; DIGIFLAG=0 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
        ; DIGIPORT=0 ; Port on which to send digi'd frames (0 = same port)
        ; USERS=0 ; Maximum number of L2 sessions, 0 = no limit
        ; ENDPORT

        ROUTES: ; Locked routes (31 maximum)
        /* ; Begin comment block
        CALLSIGN,QUALITY,PORT[,MAXFRAME,FRACK,PACLEN,INP3Enable]

        MAXFRAME, Frack and PACLEN if stated override the port defaults.
        INP3Enable = 1 enables, 0 or null disable.  The INP3 (internode protocol)
        implementation in BPQ32 is experimental.  See additional details in bpqaxip.cfg.
        Example of a route statement using INP3:
        HISCAL-12,1,1,0,0,0,1

        MYCALL-13 achieves it's internet connectivity via MYCALL-14, thus
        the quality to MYCALL-13 is set high, at 255, to obtain high
        visibility on the net via MYCALL-14.
        Locked routes tend to be overused and should not be set unless truly needed.
        */ ; End comment block
        ; NL4PRC-13,255,1 ; BPQ AX/UDP on Multiple_Apps System
        *** ; Denotes end of locked routes
        /*
        Applications:

        You can define additional Node commands that are available to your users. These may connect to
        applications running on you computer, or be aliases or 'shortcuts' to other node commands.
        For example you can define the command "BBS". This can either be set up to connect to a BBS running
        on your computer, or to be an alias for a command that connects to a BBS on another system.

        You can set up a callsign that if connected to will select the command, and if required cause the
        call to be added to your NODES list.

        The format is:

        APPLICATION n,CMD,New Command,Call,Alias, Quality

        n Application Number. You can define up to 32.
        CMD The command the user types
        New Command (optional) The Node command to be run
        Call (optional) The call which directly invokes CMD
        Alias and Quality (optional) If specified, causes an entry for Call and Alias to be added to your
        NODES table with the specified Quality.

        Associated with each Application number is an application mask. Most BPQ32 applications can be configured to 
        use any Application. An exception is AR-Cluster using the OCX interface, which must be Appl 1. Normally an Application Mask is configured in the application, rather than an Application Number. The following table gives
        the Application Mask values:

          Appl: 1,2,3,4,5,6,7,8, etc
          Decimal Mask: 1,2,4,8,16,32,64,128, etc
          Hexadecimal Mask: 0x1,0x2,0x4,0x8,0x10,0x20,0x40,0x80, etc

        */

        ; APPLICATION 1,DX,,MUDDX,255
        ; APPLICATION 1,BBS,,NL4PRC,NLD,255
        APPLICATION 1,PMS,,NL2DHR,PRC,255
        ; APPLICATION 1,BBS,,NL3DHR,DHRBBS.200

        /*

        In this example a single local application, AR-Cluster, is supported.
        If a connected user enters 'DX' the node will involk the application
        associated with the first positional parameter.

        If we elect to use the OCX interface to AR-Cluster, it must be the first
        positional parameter, as AR-Cluster does not give the user the option to
        set it's application mask, rather it is hard coded as 0x1 internally in
        AR-Cluster.

        If instead we choose to use the AGWtoBPQ interface for AR-Cluster, the
        applications may be in any of the 8 possible positions.  However we have
        chosen position 1, thus the mask in AGWtoBPQ must be configured as 0x1 to
        correspond to the first positional parameter.

        */ 
        ----------------------------------------------------------------------------------------------------------------------
      • John Wiseman
        You don t have an UNPROTO statement on the AXIP port. There is one, but it is after the CONFIG, and commented out. Add the following (before the CONFIG
        Message 3 of 14 , May 14, 2013
        • 0 Attachment
          You don't have an UNPROTO statement on the AXIP port. There is one, but it
          is after the CONFIG, and commented out.

          Add the following (before the CONFIG statement). The BCALL sets the from
          call for the beacon

          UNPROTO=NL3DHR,NL9DHR
          BCALL=NL2DHR

          73, John
        • nl2prc
          When i put these in the axip poort i get this BPQAXIP - Bad config recordUNPROTO=NL3DHR,NL9DHR BPQAXIP - bad config recordBCALL=NL2DHR I can only use these in
          Message 4 of 14 , May 14, 2013
          • 0 Attachment
            When i put these in the axip poort i get this

            BPQAXIP - Bad config recordUNPROTO=NL3DHR,NL9DHR
            BPQAXIP - bad config recordBCALL=NL2DHR

            I can only use these in the loopback port2

            And stil it is not workin

            On port2 the digi to nl9dhr is not workin

            I don't see any beacons on port 1

            Only the beacons from nl3dhr not from nl2dhr (pms call)

            Greetz ascal

            --- In BPQ32@yahoogroups.com, "John Wiseman" <john.wiseman@...> wrote:
            >
            > You don't have an UNPROTO statement on the AXIP port. There is one, but it
            > is after the CONFIG, and commented out.
            >
            > Add the following (before the CONFIG statement). The BCALL sets the from
            > call for the beacon
            >
            > UNPROTO=NL3DHR,NL9DHR
            > BCALL=NL2DHR
            >
            > 73, John
            >
          • John Wiseman
            Did you put those statements before the CONFIG line? John _____ From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of nl2prc Sent: 14 May
            Message 5 of 14 , May 14, 2013
            • 0 Attachment
              Did you put those statements before the CONFIG line?
               
              John


              From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of nl2prc
              Sent: 14 May 2013 11:47
              To: BPQ32@yahoogroups.com
              Subject: [BPQ32] Re: Tsthwin and bpq32

               

              When i put these in the axip poort i get this

              BPQAXIP - Bad config recordUNPROTO=NL3DHR,NL9DHR
              BPQAXIP - bad config recordBCALL=NL2DHR

              I can only use these in the loopback port2

              And stil it is not workin

              On port2 the digi to nl9dhr is not workin

              I don't see any beacons on port 1

              Only the beacons from nl3dhr not from nl2dhr (pms call)

              Greetz ascal

              --- In BPQ32@yahoogroups.com, "John Wiseman" <john.wiseman@...> wrote:

              >
              > You don't have an UNPROTO
              statement on the AXIP port. There is one, but it
              > is after the CONFIG,
              and commented out.
              >
              > Add the following (before the CONFIG
              statement). The BCALL sets the from
              > call for the beacon
              >
              >
              UNPROTO=NL3DHR,NL9DHR
              > BCALL=NL2DHR
              >
              > 73,
              John
              >

            • nl2prc
              Yes it works Thanks for the info Ascal
              Message 6 of 14 , May 14, 2013
              • 0 Attachment
                Yes it works

                Thanks for the info

                Ascal

                --- In BPQ32@yahoogroups.com, "John Wiseman" <john.wiseman@...> wrote:
                >
                > Did you put those statements before the CONFIG line?
                >
                > John
                >
                > _____
                >
                > From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of
                > nl2prc
                > Sent: 14 May 2013 11:47
                > To: BPQ32@yahoogroups.com
                > Subject: [BPQ32] Re: Tsthwin and bpq32
                >
                >
                >
                >
                > When i put these in the axip poort i get this
                >
                > BPQAXIP - Bad config recordUNPROTO=NL3DHR,NL9DHR
                > BPQAXIP - bad config recordBCALL=NL2DHR
                >
                > I can only use these in the loopback port2
                >
                > And stil it is not workin
                >
                > On port2 the digi to nl9dhr is not workin
                >
                > I don't see any beacons on port 1
                >
                > Only the beacons from nl3dhr not from nl2dhr (pms call)
                >
                > Greetz ascal
                >
                > --- In BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com> , "John
                > Wiseman" <john.wiseman@> wrote:
                > >
                > > You don't have an UNPROTO statement on the AXIP port. There is one, but it
                > > is after the CONFIG, and commented out.
                > >
                > > Add the following (before the CONFIG statement). The BCALL sets the from
                > > call for the beacon
                > >
                > > UNPROTO=NL3DHR,NL9DHR
                > > BCALL=NL2DHR
                > >
                > > 73, John
                > >
                >
              • Charles Brabham
                It may be that by linking BPQ32 to the FLARQ/FLDIGI programs in the NBEMS suite, we would then have access to a number of new ARQ modes. 73 DE Charles, N5PVL
                Message 7 of 14 , May 14, 2013
                • 0 Attachment
                  It may be that by linking BPQ32 to the FLARQ/FLDIGI  programs in the NBEMS suite, we would then have access to a number of new ARQ modes.
                   
                  73 DE Charles, N5PVL
                   
                • PD0SNK
                  cool did not know one could set multiple unproto adresses unproto=call,call (via)
                  Message 8 of 14 , May 14, 2013
                  • 0 Attachment
                    cool did not know one could set multiple unproto adresses

                    unproto=call,call (via)



                    --- In BPQ32@yahoogroups.com, "nl2prc" <nl2prc@...> wrote:
                    >
                    > Yes it works
                    >
                    > Thanks for the info
                    >
                    > Ascal
                    >
                    > --- In BPQ32@yahoogroups.com, "John Wiseman" <john.wiseman@> wrote:
                    > >
                    > > Did you put those statements before the CONFIG line?
                    > >
                    > > John
                    > >
                    > > _____
                    > >
                    > > From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of
                    > > nl2prc
                    > > Sent: 14 May 2013 11:47
                    > > To: BPQ32@yahoogroups.com
                    > > Subject: [BPQ32] Re: Tsthwin and bpq32
                    > >
                    > >
                    > >
                    > >
                    > > When i put these in the axip poort i get this
                    > >
                    > > BPQAXIP - Bad config recordUNPROTO=NL3DHR,NL9DHR
                    > > BPQAXIP - bad config recordBCALL=NL2DHR
                    > >
                    > > I can only use these in the loopback port2
                    > >
                    > > And stil it is not workin
                    > >
                    > > On port2 the digi to nl9dhr is not workin
                    > >
                    > > I don't see any beacons on port 1
                    > >
                    > > Only the beacons from nl3dhr not from nl2dhr (pms call)
                    > >
                    > > Greetz ascal
                    > >
                    > > --- In BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com> , "John
                    > > Wiseman" <john.wiseman@> wrote:
                    > > >
                    > > > You don't have an UNPROTO statement on the AXIP port. There is one, but it
                    > > > is after the CONFIG, and commented out.
                    > > >
                    > > > Add the following (before the CONFIG statement). The BCALL sets the from
                    > > > call for the beacon
                    > > >
                    > > > UNPROTO=NL3DHR,NL9DHR
                    > > > BCALL=NL2DHR
                    > > >
                    > > > 73, John
                    > > >
                    > >
                    >
                  Your message has been successfully submitted and would be delivered to recipients shortly.