Loading ...
Sorry, an error occurred while loading the content.

Re: comports hex or decimal.

Expand Messages
  • James Mcdowall
    Thank you both for the reply i get working on the ports now
    Message 1 of 7 , Apr 29, 2013
    • 0 Attachment
      Thank you both for the reply i get working on the ports now

      --- In BPQ32@yahoogroups.com, "Mike" <mmelnik1@...> wrote:
      >
      > Jim
      >
      >
      >
      > The following is a standard bpq32.cfg Kiss Port, the com port number to be
      > used is IOADDR=1 For Com 1
      >
      > =3 for Com 3 etc. the BAUD Rate is SPEED=
      >
      >
      >
      > Since you did not mention if your TNC'S were a multi port I assume you are
      > using 4 different TNC'S.
      >
      > If a TNC is a multiport TNC the IOADDR= will be the same for that TNC, you
      > only use Channel=A and Channel=B, etc.
      >
      >
      >
      > Remember to set the TNC'S in KISS mode before starting BPQ32 and/or Programs
      > used by BPQ32.
      >
      >
      >
      > If you have any problems let me know.
      >
      >
      >
      > 73
      >
      >
      >
      > PORT
      >
      > ID=145.030 MHz ; Displayed by PORTS command
      >
      > TYPE=ASYNC ; Port is RS232 Com, Kantronics 9612 Ch A
      >
      > PROTOCOL=KISS ; TNC is used in KISS mode
      >
      > NOKEEPALIVES=1 ; No Net Rom Polling
      >
      > FULLDUP=0 ; Only meaningful for KISS devices
      >
      > IOADDR=1 ; 1 = SERIAL PORT COM1 ETC.
      >
      > SPEED=9600 ; RS232 COM PORT SPEED
      >
      > CHANNEL=A ; Address if multichannel TNC
      >
      > PERSIST=225 ; PERSIST=256/(# of transmitters-1)
      >
      > SLOTTIME=100 ; CMSA interval timer in milliseconds
      >
      > TXDELAY=280 ; Transmit keyup delay in milliseconds
      >
      > TXTAIL=0 ; TX key down, in milliseconds, at
      > packet end
      >
      > QUALITY=192 ; Quality factor applied to node
      > broadcasts heard on
      >
      > ; this port, unless
      > overridden by a locked route
      >
      > ; entry. Setting to 0 stops
      > node broadcasts
      >
      > MINQUAL=168 ; Entries in the nodes table with
      > qualities greater or
      >
      > ; equal to MINQUAL will be
      > sent on this port. A value
      >
      > ; of 0 sends everything.
      >
      > MAXFRAME=2 ; Max outstanding frames (1 thru 7)
      >
      > FRACK=5000 ; Level 2 timout in milliseconds
      >
      > RESPTIME=2000 ; Level 2 delayed ack timer in
      > milliseconds
      >
      > RETRIES=6 ; Level 2 maximum retry value
      >
      > PACLEN=236 ; Default max packet length for this
      > port
      >
      > UNPROTO=BPQ Port 1 ; BTEXT Broadcast
      >
      > BCALL=N9PMO-2 ; BTEXT call. unstated defaults to
      > BBSCALL/APPL1CALL
      >
      > L3ONLY=0 ; 1=No user downlink connects on this
      > port
      >
      > DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
      >
      > DIGIPORT=0 ; Port on which to send digi'd frames
      > (0 = same port)
      >
      > USERS=0 ; Maximum number of L2 sessions, 0 =
      > no limit
      >
      > ENDPORT
      >
      >
      >
      > Mike N9PMO
      > <http://www.n9pmo.com> www.n9pmo.com
      >
      > -----Original Message-----
      > From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of
      > James Mcdowall
      > Sent: Monday, April 29, 2013 7:26 AM
      > To: BPQ32@yahoogroups.com
      > Subject: [BPQ32] comports hex or decimal.
      >
      >
      >
      >
      >
      > i am swapping my agwpe tnc ports so bpq connect to them direct
      > but not shure how
      >
      > com 1,3,4,6 are what there on now via agwpe
      > how do i write it into the cfg
      > there all at 9600
      > COMPORT=?
      > IOADDR=?
      > SPEED=?
      >
      > Cheers jim
      >
    • James Mcdowall
      Can anyone see were i have gone wrong only port 2 is working on com1 com3,4,5,6 are not? cheers jim PORT PORTNUM=2 ID=144.950 MHz TYPE=ASYNC PROTOCOL=KISS
      Message 2 of 7 , Apr 30, 2013
      • 0 Attachment
        Can anyone see were i have gone wrong only port 2 is working on com1
        com3,4,5,6 are not? cheers jim

        PORT
        PORTNUM=2
        ID=144.950 MHz
        TYPE=ASYNC
        PROTOCOL=KISS
        FULLDUP=1
        IOADDR=1
        SPEED=9600
        CHANNEL=A
        PERSIST=225
        SLOTTIME=100
        TXDELAY=500
        TXTAIL=0
        QUALITY=0
        MINQUAL=168
        MAXFRAME=2
        FRACK=5000
        RESPTIME=2000
        RETRIES=15
        PACLEN=100
        BCALL=g7icd-1
        DIGIFLAG=1
        DIGIPORT=0
        USERS=0
        ENDPORT
        ;
        PORT
        PORTNUM=3
        ID=432.675
        TYPE=ASYNC
        PROTOCOL=KISS
        FULLDUP=1
        IOADDR=4
        SPEED=2400
        CHANNEL=A
        PERSIST=225
        SLOTTIME=100
        TXDELAY=500
        TXTAIL=0
        QUALITY=0
        MINQUAL=168
        MAXFRAME=2
        FRACK=5000
        RESPTIME=2000
        RETRIES=15
        PACLEN=100
        BCALL=g7icd-1
        L3ONLY=0
        DIGIFLAG=1
        DIGIPORT=0
        USERS=0
        ENDPORT
        ;
        PORT
        PORTNUM=7
        ID=UHF 433.650
        TYPE=ASYNC
        PROTOCOL=KISS
        NOKEEPALIVES=1
        FULLDUP=1
        IOADDR=6
        SPEED=9600
        CHANNEL=A
        PERSIST=225
        SLOTTIME=100
        TXDELAY=500
        TXTAIL=0
        QUALITY=0
        MINQUAL=168
        MAXFRAME=2
        FRACK=5000
        RESPTIME=2000
        RETRIES=15
        PACLEN=100
        BCALL=g7icd-1
        L3ONLY=0
        DIGIFLAG=1
        DIGIPORT=0
        USERS=0

        ENDPORT
        ;
        PORT
        PORTNUM=10
        ID=HF 29.250
        TYPE=ASYNC
        PROTOCOL=KISS
        NOKEEPALIVES=1
        FULLDUP=1
        IOADDR=3
        SPEED=9600
        CHANNEL=A
        PERSIST=225
        SLOTTIME=100
        TXDELAY=500
        TXTAIL=0
        QUALITY=0
        MINQUAL=168
        MAXFRAME=2
        FRACK=5000
        RESPTIME=2000
        RETRIES=15
        PACLEN=100
        BCALL=g7icd-1
        L3ONLY=0
        DIGIFLAG=1
        DIGIPORT=0
        USERS=0

        ENDPORT
      • James Mcdowall
        all sorted now the tnc had come out of kiss mode
        Message 3 of 7 , Apr 30, 2013
        • 0 Attachment
          all sorted now the tnc had come out of kiss mode


          --- In BPQ32@yahoogroups.com, "James Mcdowall" <runcnode@...> wrote:
          >
          > Can anyone see were i have gone wrong only port 2 is working on com1
          > com3,4,5,6 are not? cheers jim
          >
          > PORT
          > PORTNUM=2
          > ID=144.950 MHz
          > TYPE=ASYNC
          > PROTOCOL=KISS
          > FULLDUP=1
          > IOADDR=1
          > SPEED=9600
          > CHANNEL=A
          > PERSIST=225
          > SLOTTIME=100
          > TXDELAY=500
          > TXTAIL=0
          > QUALITY=0
          > MINQUAL=168
          > MAXFRAME=2
          > FRACK=5000
          > RESPTIME=2000
          > RETRIES=15
          > PACLEN=100
          > BCALL=g7icd-1
          > DIGIFLAG=1
          > DIGIPORT=0
          > USERS=0
          > ENDPORT
          > ;
          > PORT
          > PORTNUM=3
          > ID=432.675
          > TYPE=ASYNC
          > PROTOCOL=KISS
          > FULLDUP=1
          > IOADDR=4
          > SPEED=2400
          > CHANNEL=A
          > PERSIST=225
          > SLOTTIME=100
          > TXDELAY=500
          > TXTAIL=0
          > QUALITY=0
          > MINQUAL=168
          > MAXFRAME=2
          > FRACK=5000
          > RESPTIME=2000
          > RETRIES=15
          > PACLEN=100
          > BCALL=g7icd-1
          > L3ONLY=0
          > DIGIFLAG=1
          > DIGIPORT=0
          > USERS=0
          > ENDPORT
          > ;
          > PORT
          > PORTNUM=7
          > ID=UHF 433.650
          > TYPE=ASYNC
          > PROTOCOL=KISS
          > NOKEEPALIVES=1
          > FULLDUP=1
          > IOADDR=6
          > SPEED=9600
          > CHANNEL=A
          > PERSIST=225
          > SLOTTIME=100
          > TXDELAY=500
          > TXTAIL=0
          > QUALITY=0
          > MINQUAL=168
          > MAXFRAME=2
          > FRACK=5000
          > RESPTIME=2000
          > RETRIES=15
          > PACLEN=100
          > BCALL=g7icd-1
          > L3ONLY=0
          > DIGIFLAG=1
          > DIGIPORT=0
          > USERS=0
          >
          > ENDPORT
          > ;
          > PORT
          > PORTNUM=10
          > ID=HF 29.250
          > TYPE=ASYNC
          > PROTOCOL=KISS
          > NOKEEPALIVES=1
          > FULLDUP=1
          > IOADDR=3
          > SPEED=9600
          > CHANNEL=A
          > PERSIST=225
          > SLOTTIME=100
          > TXDELAY=500
          > TXTAIL=0
          > QUALITY=0
          > MINQUAL=168
          > MAXFRAME=2
          > FRACK=5000
          > RESPTIME=2000
          > RETRIES=15
          > PACLEN=100
          > BCALL=g7icd-1
          > L3ONLY=0
          > DIGIFLAG=1
          > DIGIPORT=0
          > USERS=0
          >
          > ENDPORT
          >
        • Mike
          Jim I just tested your configuration, all works fine, two things I see however they will not Stop communications, (1) you have FULLDUP=1 (Enabled) this can
          Message 4 of 7 , Apr 30, 2013
          • 0 Attachment
            Jim

            I just tested your configuration, all works fine, two things I see however
            they will not
            Stop communications,
            (1) you have FULLDUP=1 (Enabled) this can cause packets to collide.
            (2) UNPROTO= Statement is missing, the only effect this will have is no
            BTexts from BPQ32
            will be sent.

            73

            Mike N9PMO
            www.n9pmo.com
            -----Original Message-----
            From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of
            James Mcdowall
            Sent: Tuesday, April 30, 2013 9:02 AM
            To: BPQ32@yahoogroups.com
            Subject: [BPQ32] Re: comports hex or decimal.

             
            all sorted now the tnc had come out of kiss mode

            --- In BPQ32@yahoogroups.com, "James Mcdowall" <runcnode@...> wrote:
            >
            > Can anyone see were i have gone wrong only port 2 is working on com1
            > com3,4,5,6 are not? cheers jim
            >
            > PORT
            > PORTNUM=2
            > ID=144.950 MHz
            > TYPE=ASYNC
            > PROTOCOL=KISS
            > FULLDUP=1
            > IOADDR=1
            > SPEED=9600
            > CHANNEL=A
            > PERSIST=225
            > SLOTTIME=100
            > TXDELAY=500
            > TXTAIL=0
            > QUALITY=0
            > MINQUAL=168
            > MAXFRAME=2
            > FRACK=5000
            > RESPTIME=2000
            > RETRIES=15
            > PACLEN=100
            > BCALL=g7icd-1
            > DIGIFLAG=1
            > DIGIPORT=0
            > USERS=0
            > ENDPORT
            > ;
            > PORT
            > PORTNUM=3
            > ID=432.675
            > TYPE=ASYNC
            > PROTOCOL=KISS
            > FULLDUP=1
            > IOADDR=4
            > SPEED=2400
            > CHANNEL=A
            > PERSIST=225
            > SLOTTIME=100
            > TXDELAY=500
            > TXTAIL=0
            > QUALITY=0
            > MINQUAL=168
            > MAXFRAME=2
            > FRACK=5000
            > RESPTIME=2000
            > RETRIES=15
            > PACLEN=100
            > BCALL=g7icd-1
            > L3ONLY=0
            > DIGIFLAG=1
            > DIGIPORT=0
            > USERS=0
            > ENDPORT
            > ;
            > PORT
            > PORTNUM=7
            > ID=UHF 433.650
            > TYPE=ASYNC
            > PROTOCOL=KISS
            > NOKEEPALIVES=1
            > FULLDUP=1
            > IOADDR=6
            > SPEED=9600
            > CHANNEL=A
            > PERSIST=225
            > SLOTTIME=100
            > TXDELAY=500
            > TXTAIL=0
            > QUALITY=0
            > MINQUAL=168
            > MAXFRAME=2
            > FRACK=5000
            > RESPTIME=2000
            > RETRIES=15
            > PACLEN=100
            > BCALL=g7icd-1
            > L3ONLY=0
            > DIGIFLAG=1
            > DIGIPORT=0
            > USERS=0
            >
            > ENDPORT
            > ;
            > PORT
            > PORTNUM=10
            > ID=HF 29.250
            > TYPE=ASYNC
            > PROTOCOL=KISS
            > NOKEEPALIVES=1
            > FULLDUP=1
            > IOADDR=3
            > SPEED=9600
            > CHANNEL=A
            > PERSIST=225
            > SLOTTIME=100
            > TXDELAY=500
            > TXTAIL=0
            > QUALITY=0
            > MINQUAL=168
            > MAXFRAME=2
            > FRACK=5000
            > RESPTIME=2000
            > RETRIES=15
            > PACLEN=100
            > BCALL=g7icd-1
            > L3ONLY=0
            > DIGIFLAG=1
            > DIGIPORT=0
            > USERS=0
            >
            > ENDPORT
            >
          Your message has been successfully submitted and would be delivered to recipients shortly.