Loading ...
Sorry, an error occurred while loading the content.
 

Re: BPQ connect via rf vs ip

Expand Messages
  • KU4GW Cliff
    The C 1 Alias-1 works for me too! Thank you for telling me a much more simple way to do this also! Very 73 de Cliff KU4GW
    Message 1 of 11 , Apr 16, 2013
      The C 1 Alias-1 works for me too! Thank you for telling me a much more simple way to do this also!

      Very 73 de Cliff KU4GW


      --- In BPQ32@yahoogroups.com, "John Wiseman" <john.wiseman@...> wrote:
      >
      > Hannes, (and other respondents)
      >
      > That is the correct way, and is even documented!
      >
      > From <http://www.cantab.net/users/john.wiseman/Documents/Commands.htm>
      > http://www.cantab.net/users/john.wiseman/Documents/Commands.htm
      >
      > "Normally you cannot override the automatic route selection when you connect
      > to another node, but you can fool the system into thinking a node is a
      > normal station by connecting to the alias, and adding an SSID. For example,
      > if you want to connect to NOTTS:G8BPQ-3, you can force a Level 2 connect
      > on a secified port by entering C P NOTTS-1"
      >
      > 73, John
      >
      >
      > _____
      >
      > From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of CJ
      > Hanekom
      > Sent: 16 April 2013 06:02
      > To: BPQ32@yahoogroups.com
      > Subject: Re: [BPQ32] Re: BPQ connect via rf vs ip
      >
      >
      >
      >
      >
      > Thanks for all the replies, using "c port alias-1" worked for me.
      >
      > Regards
      >
      > Hannes
      > ZL1LW
      > Node: TORBAY
      >
      >
      > On 16/04/13 16:23, Harold Kinchelow wrote:
      >
      >
      >
      >
      > To force a connect, do c (port number) (aliase)-0
      >
      > Sent from a smartphone. Owner makes typo's for sure.
      >
      > On Apr 15, 2013 8:59 PM, "KU4GW Cliff" <cliffku4gw@...> wrote:
      >
      >
      >
      >
      >
      >
      > Hi John,
      > I had a local node that I could not get a connect to via port 1. It would
      > always try via the web (port 3) even if I typed C 1 <Callsign>. The way I
      > finally got it to connect on port 1 using BPQ32 Version 6.0.1.1. was I had
      > to go to the node window labeled at the top BPQ32.dll Console Version
      > 6.0.1.1 (It's the window that tells you all your ports are configured
      > correctly when you first boot up) and click on the border of the window to
      > highlight it and then look all the way up to the top left side of your PC
      > screen and you'll see a drop down list that says ACTION. Click on Action and
      > then click Clear Nodes, reread bpq32.cfg file, and reconfigure node. Then
      > you will be able to connect by typing C 1 <Callsign>. Don't worry about your
      > node list because it will immediately rebuild from another network node.Keep
      > these instructions handy because you may have to do it again in the future.
      > Thanks go to KF4LLF Seth for telling me how to do this!
      >
      > Very 73,
      > Cliff - KU4GW
      > BRTMTN:KU4GW-7 Sysop
      >
      > --- In BPQ32@yahoogroups.com <mailto:BPQ32%40yahoogroups.com> , Hannes
      > Hanekom <mailto:hanneshanekom@> <hanneshanekom@> wrote:
      > >
      > > Hi John,
      > >
      > > I have an application configured to node `test` on my linbpq config to
      > > connect to it via IP. This station has an rf port with radio attached to
      > > it. When I attempt to connect to this station via rf instead op ip using c
      > > 1 test, From linbpq or winbpq it connects via ip and not via rf. My rf
      > > port is port 1, and ip port on port 2. How can i connect to node `test`
      > via
      > > rf instead of ip?
      > >
      > > Regards
      > >
      > > Hannes
      > > ZL1LW.
      > >
      >
    Your message has been successfully submitted and would be delivered to recipients shortly.