Loading ...
Sorry, an error occurred while loading the content.

9401RE: [BPQ32] Re: opening com 1 in bpq

Expand Messages
  • Mike
    Dec 10, 2012
    • 0 Attachment
      Don

      Right click on My Computer, Left click on Properties, Hardware Tab,
      Device manager, then down to Ports (COM & LPT) click on the + mark
      To expand, this will tell you if Communications port 1 is available
      Or has an error, an error will be indicated with a red or yellow
      Mark over the port.

      You should increase the BAUD rate to 19200 in bpq32.cfg and TNC,
      Any BUAD rate less on a dual port TNC may cause problems.

      Mike N9PMO
      www.n9pmo.com
      -----Original Message-----
      From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of
      Don P
      Sent: Monday, December 10, 2012 6:18 AM
      To: BPQ32@yahoogroups.com
      Subject: [BPQ32] Re: opening com 1 in bpq

       
      Hi, John

      That com1 can't be opened...No specific error message, I should have
      clarified that...

      --- In BPQ32@yahoogroups.com, "John Wiseman" <john.wiseman@...> wrote:
      >
      > What error messagre do you get?
      >
      > John
      >
      > _____
      >
      > From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf
      Of Don
      > P
      > Sent: 09 December 2012 19:42
      > To: BPQ32@yahoogroups.com
      > Subject: [BPQ32] opening com 1 in bpq
      >
      >
      >
      >
      > I can access my kam via com 1 using a terminal program and place the
      kam
      > into kiss: kissmode on, reset
      >
      > However, I get an error from bpq on com 1 when starting
      >
      > PORT ; KAM TNC HF Packet Port
      > PORTNUM=3 ; Optional but sets port number if stated
      > ID=BPQ 7.1035 KAM ; Displayed by PORTS command
      > TYPE=ASYNC ; Port is RS232 Com
      > PROTOCOL=KISS ; TNC is used in KISS mode
      > FULLDUP=0 ; Only meaningful for KISS devices
      > IOADDR=1 ; 1 = SERIAL PORT COM1 ETC.
      > SPEED=9600 ; RS232 COM PORT SPEED
      > CHANNEL=B ; A for single channel TNC, A or B for multichannel
      > PERSIST=200 ; PERSIST=256/(# of transmitters-1)
      > SLOTTIME=100 ; CMSA interval timer in milliseconds
      > TXDELAY=760 ; Transmit keyup delay in milliseconds
      > TXTAIL=83 ; TX key down, in milliseconds, at packet end;
      > QUALITY=0 ; Quality factor applied to node broadcasts heard on
      > ; this port, unless overridden by a locked route
      > ; entry. Setting to 0 stops node broadcasts
      > MINQUAL=172 ; Entries in the nodes table with qualities greater or
      > ; equal to MINQUAL will be sent on this port. A value
      > ; of 0 sends everything.
      > MAXFRAME=1 ; Max outstanding frames (1 thru 7)
      > FRACK=5000 ; Level 2 timout in milliseconds
      > RESPTIME=4000 ; Level 2 delayed ack timer in milliseconds
      > RETRIES=8 ; Level 2 maximum retry value
      > PACLEN=40 ; Default max packet length for this port
      > UNPROTO=Nodes: ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
      > BCALL=w9jun-1 ; BTEXT call. unstated defaults to APPL1CALL
      > L3ONLY=0 ; 1=No user downlink connects on this port
      > DIGIFLAG=0 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
      > DIGIPORT=0 ; Port on which to send digi'd frames (0 = same port)
      > USERS=1 ; Maximum number of L2 sessions, 0 = no limit
      > WL2KREPORT PUBLIC, www.winlink.org, 8778, W9JUN-10, EM78gs, 00-23,
      7103500,
      > PKT300, 50, 20, 3, 0
      > ENDPORT
      >
    • Show all 6 messages in this topic