Loading ...
Sorry, an error occurred while loading the content.

9303Re: [BPQ32] 9600 baud packet instability

Expand Messages
  • Bob Unger
    Nov 15, 2012
    • 0 Attachment
      Jerry, I am gloing to put some jupdates to this and get it back to you asap.  hope it works better....
       
      73 de Bob

      From: Jerry <n9lya@...>
      To: BPQ32@yahoogroups.com
      Sent: Wednesday, November 14, 2012 5:39 PM
      Subject: RE: [BPQ32] 9600 baud packet instability
       
      Ill look yours over more in morning… But here are mine I use a KPC9612 as well mine feeds an Icom 38A
       
      Have you adjusted your TX audio and equalization in the TNC…??? 73 Jerry N9LYA
       
      PORT                                     ; 220 Meter Emcom FREQ.
      PORTNUM=9                    ; Optional but sets port number if stated
      ID=9600 223.600 MHz    ; Displayed by PORTS command
      TYPE=ASYNC                     ; Port is RS232 Com
      PROTOCOL=KISS                             ; TNC is used in KISS mode
      FULLDUP=0                       ; Only meaningful for KISS devices
      IOADDR=C                         ; 1 = SERIAL PORT COM1 ETC.
      SPEED=9600                      ; RS232 COM PORT SPEED
      CHANNEL=B                      ; A for single channel TNC, A or B for multichannel
      PERSIST=64                        ; PERSIST=256/(# of transmitters-1)
      SLOTTIME=100                 ; CMSA interval timer in milliseconds
      TXDELAY=300                    ; Transmit keyup delay in milliseconds
      TXTAIL=0                            ; TX key down, in milliseconds, at packet end;
      QUALITY=192                    ; Quality factor applied to node broadcasts heard on
                                                      ; this port, unless overridden by a locked route
                                                      ; entry. Setting to 0 stops node broadcasts
      MINQUAL=95                   ; Entries in the nodes table with qualities greater or
                                                      ; equal to MINQUAL will be sent on this port. A value
                                                      ; of 0 sends everything.
      MAXFRAME=2                 ; Max outstanding frames (1 thru 7)
      FRACK=5000                      ; Level 2 timout in milliseconds
      RESPTIME=1000                               ; Level 2 delayed ack timer in milliseconds
      RETRIES=10                        ; Level 2 maximum retry value
      PACLEN=236                     ; Default max packet length for this port
      UNPROTO=Nodes:                         ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
      BCALL=n9lya-7                 ; BTEXT call. unstated defaults to APPL1CALL
      L3ONLY=0                           ; 1=No user downlink connects on this port
      DIGIFLAG=1                      ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
      DIGIPORT=0                      ; Port on which to send digi'd frames (0 = same port)
      USERS=0                             ; Maximum number of L2 sessions, 0 = no limit
      WL2KREPORT PUBLIC, http://www.winlink.org/, 8778, K9BBS-10, EM68SR, 00-23, 223600000, PKT9600, 65, 35, 5, 0
      ENDPORT
       
      From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of k1jtc
      Sent: Wednesday, November 14, 2012 5:32 PM
      To: BPQ32@yahoogroups.com
      Subject: [BPQ32] 9600 baud packet instability
       
       
      We are having problems with consistent connects using outpost. When using hyperterminal it connects better but still retries muliple times. Below are the settings that I have in the config file. I am using a kantronics 9612. Any suggestions to make it more stable would be greatly appreciated.

      PORT
      PORTNUM=1 ; Optional but sets port number if stated
      ID=BBS 223.520 MHz ; Displayed by PORTS command
      TYPE=ASYNC ; Port is RS232 Com
      PROTOCOL=KISS ; TNC is used in KISS (or JKISS) mode
      ; See ..\RelatedFiles\KissRoms\KissRoms.zip.
      FULLDUP=0 ; Only meaningful for KISS (or JKISS) devices
      IOADDR=1 ; 1 = SERIAL PORT COM1 ETC.
      SPEED=9600 ; RS232 COM PORT SPEED
      CHANNEL=B ; A for single channel TNC, A or B for multichannel
      PERSIST=64 ; PERSIST=256/(# of transmitters-1)
      SLOTTIME=50 ; CMSA interval timer in milliseconds
      TXDELAY=300 ; Transmit keyup delay in milliseconds
      TXTAIL=30 ; TX key down, in milliseconds, at packet end
      QUALITY=125 ; Quality factor applied to node broadcasts heard on
      ; this port, unless overridden by a locked route
      ; entry. Setting to 0 stops node broadcasts
      MINQUAL=0 ; Entries in the nodes table with qualities greater or
      ; equal to MINQUAL will be sent on this port. A value
      ; of 0 sends everything.
      MAXFRAME=4 ; Max outstanding frames (1 thru 7)
      FRACK=5000 ; Level 2 timout in milliseconds
      RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
      RETRIES=5 ; Level 2 maximum retry value
      PACLEN=125 ; Default max packet length for this port
      UNPROTO=ANTBBS ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
      BCALL=K1JTC-10 ; BTEXT call. unstated defaults to APPL1CALL
      L3ONLY=0 ; 1=No user downlink connects on this port
      DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
      DIGIPORT=0 ; Port on which to send digi'd frames (0 = same port)
      USERS=0 ; Maximum number of L2 sessions, 0 = no limit
      ENDPORT
    • Show all 23 messages in this topic