Loading ...
Sorry, an error occurred while loading the content.

929RE: [BPQ32] config bpqcfg.txt with pk232 on fbbwin

Expand Messages
  • David Chadufaud
    Jan 31, 2008
    • 0 Attachment
      hi i tried it
      the answer is

      INFO
      EDFNOD:VE2EDF-3} Type DX to connect to the DX Cluster.
      DX
      EDFNOD:VE2EDF-3} Invalid command - Enter ? for command list
      c ve2edf-3
      EDFNOD:VE2EDF-3} Downlink connect needs port number - C P CALLSIGN
      Ports:
        1 BPQ 145.050 MHz              
        2 AX/IP/UDP                    
      c 1 ve2edf-3
      EDFNOD:VE2EDF-3} Failure with VE2EDF-3 
      ?
      EDFNOD:VE2EDF-3} BBS CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD
      nodes
      EDFNOD:VE2EDF-3} Nodes:
      PMSEDF:VE2EDF-1   
      mheard 1
      EDFNOD:VE2EDF-3} Heard List for Port 1
      connect
      EDFNOD:VE2EDF-3} Sorry, All HOST Ports are in use - Please try later

      so i think i can't connect my node isn't ?
      and my bpq32 is like that
      ; CONFIGURATION FILE FOR BPQ32: G8BPQ SWITCH SOFTWARE
      ; Includes 1 KISS TNC Port, and 1 AX/IP/UDP Port.
      ; See the corresponding bpqaxip.cfg file for more configuration details.
      ; \Examples\Medium
      HOSTINTERRUPT=127 ; Interrupt used for BPQ host mode support
      EMS=0   ; Doesn't use EMS RAM
      DESQVIEW=0  ; DesqView unused
      NODECALL=VE2EDF-3 ; Node callsign
      NODEALIAS=EDFNOD ; Node alias (6 characters max)
      BBSCALL=VE2EDF-1  ; BBS callsign APPL1CALL if used overrides BBSCALL
      BBSALIAS=PMSEDF  ; BBS alias APPL1ALIAS if used overrides BBSALIAS
      IDMSG:   ; UI broadcast text from NODECALL to fixed dest ID
      ;N5IN Thief River Falls MN 144.39 APRS/147.525 DX-Cluster
      ***   ; Denotes end of IDMSG text
      BTEXT:   ; UI broadcast text from BCALL to destination UNPROTO=
      ;!4806.56N/09611.70W%Thief River Falls MN 144.39 APRS/147.525 DX-Cluster
      ***   ; Denotes end of BTEXT text
      INFOMSG:  ; The INFO command text follows:
      Type DX to connect to the DX Cluster.
      ***   ; Denotes end of INFOMSG text
      CTEXT:   ; The CTEXT text follows:
      Type DX to connect to the DX Cluster.
      TRFDX1:N5IN-14} DX CONNECT BYE INFO NODES ROUTES PORTS USERS MHEARD
      ***   ; Denotes end of CTEXT text
      FULL_CTEXT=1  ; 0=send CTEXT to L2 connects to NODEALIAS only
         ; 1=send CTEXT to all connectees
      ; Network System Parameters:
      OBSINIT=6  ; Initial obsolescence set when a node is included
         ; in a received nodes broadcast. This value is then
         ; decremented by 1 every NODESINTERVAL.
      OBSMIN=4  ; When the obsolescence of a node falls below this
         ; value that node's information is not included in
         ; a subsequent nodes broadcast.
      NODESINTERVAL=15 ; Nodes broadcast interval in minutes
      IDINTERVAL=60  ; 'IDMSG' UI broadcast interval in minutes, 0=OFF
      BTINTERVAL=60  ; The BTEXT broadcast interval in minutes, 0=OFF
      L3TIMETOLIVE=25  ; Max L3 hops
      L4RETRIES=3  ; Level 4 retry count
      L4TIMEOUT=60  ; Level 4 timeout in seconds s/b > FRACK x RETRIES
      L4DELAY=10  ; Level 4 delayed ack timer in seconds
      L4WINDOW=4  ; Level 4 window size
      MAXLINKS=63  ; Max level 2 links
      MAXNODES=128  ; Max nodes in nodes table
      MAXROUTES=64  ; Max adjacent nodes
      MAXCIRCUITS=128  ; Max L4 circuits
      MINQUAL=168  ; Minimum quality to add to nodes table
      BBSQUAL=255  ; BBS quality multiplier, (BBSQUAL/256), relative to
         ; NODE. Used to limit spread of BBS node info through
         ; the network to your required service area. [0,255].
         ; APPL1QUAL if used overrides BBSQUAL.
      BUFFERS=255  ; Packet buffers - 255 means allocate as many as
         ; possible, normally about 130, depending upon other
         ; table sizes.
      ; TNC default parameters:
      PACLEN=236  ; Max packet size (236 max for net/rom)
      ; PACLEN is a problem! The ideal size depends on the link(s) over which a
      ; packet will be sent. For a session involving another node, we have no idea
      ; what is at the far end. Ideally each node should have the capability to
      ; combine and then refragment messages to suit each link segment - maybe when
      ; there are more BPQ nodes about than 'other' ones, I'll do it. When the node
      ; is accessed directly, things are a bit easier, as we know at least something
      ; about the link. So, currently there are two PACLEN params, one here and one
      ; in the PORTS section. This one is used to set the initial value for
      ; sessions via other nodes and for sessions initiated from here. The other is
      ; used for incoming direct (Level 2) sessions. In all cases the TNC PACLEN
      ; command can be used to override the defaults.
      TRANSDELAY=1  ; Transparent node send delay in seconds
      ; Level 2 Parameters:
      ; T1 (FRACK), T2 (RESPTIME) and N2 (RETRIES) are now in the PORTS section
      T3=120   ; Link validation timer in seconds
      IDLETIME=600  ; Idle link shutdown timer in seconds
      ; Configuration Options:
      AUTOSAVE=1  ; Saves BPQNODES.dat upon program exit
      BBS=1   ; 1 = BBS support included, 0 = No BBS support
      NODE=1   ; Include switch support
      HIDENODES=1  ; If set to 1, nodes beginning with a #
         ; require a 'N *' command to be displayed.
      ; The *** LINKED command is intended for use by gateway software, and concern
      ; has been expressed that it could be misused. It is recommended that it be
      ; disabled (=N) if unneeded.
      ENABLE_LINKED=N  ; Controls processing of *** LINKED command
         ; Y = allows unrestricted use
         ; A = allows use by application program
         ; N = disabled
      ; AX25 port definitions:
      ; With the following definition BPQ32 accesses the TNC directly.
      PORT
       PORTNUM=1  ; Optional but sets port number if stated
       ID=BPQ 145.050 MHz ; Displayed by PORTS command
       TYPE=ASYNC  ; Port is RS232 Com
       PROTOCOL=KISS  ; TNC is used in KISS mode
       FULLDUP=0  ; Only meaningful for KISS devices
       IOADDR=1  ; 1 = SERIAL PORT COM1 ETC.
       SPEED=9600  ; RS232 COM PORT SPEED
       CHANNEL=  ; Address if multichannel TNC
       PERSIST=64  ; PERSIST=256/(# of transmitters-1)
       SLOTTIME=100  ; CMSA interval timer in milliseconds
       TXDELAY=30  ; Transmit keyup delay in milliseconds
       TXTAIL=30  ; TX key down, in milliseconds, at packet end
       QUALITY=192  ; Quality factor applied to node broadcasts heard on
         ; this port, unless overridden by a locked route
         ; entry. Setting to 0 stops node broadcasts
       MINQUAL=168  ; Entries in the nodes table with qualities greater or
         ; equal to MINQUAL will be sent on this port. A value
         ; of 0 sends everything.
       MAXFRAME=7  ; Max outstanding frames (1 thru 7)
       FRACK=5000  ; Level 2 timout in milliseconds
       RESPTIME=1000  ; Level 2 delayed ack timer in milliseconds
       RETRIES=5  ; Level 2 maximum retry value
       PACLEN=236  ; Default max packet length for this port
       UNPROTO=VE2RSP  ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
       BCALL=VE2EDF-3  ; BTEXT call. unstated defaults to BBSCALL/APPL1CALL
       L3ONLY=0  ; 1=No user downlink connects on this port
       DIGIFLAG=1  ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
       DIGIPORT=0  ; Port on which to send digi'd frames (0 = same port)
       USERS=0  ; Maximum number of L2 sessions, 0 = no limit
      ENDPORT
      ; With the following definition, BPQ32 uses AGWPE to access the TNC. To avoid
      ; a port conflict with AGWtoBPQ (by default both AGWtoBPQ's and AGWPE's
      ; interface port is 8000), the port for AGWPE has been set here to 8001 and
      ; thus AGWPE itself must be configured to also use port 8001.
      ; With BPQtoAGW, BPQ32 does level 2 and above, AGWPE does level 1. Thus
      ; Persist, Slottime, TXDelay and TxTail, if stated, are not used and
      ; must be set instead in AGWPE. MaxFrame, Retries, Frack and Resptime
      ; are done by BPQ32.
      ;PORT
      ; PORTNUM=1  ; Optional but sets port number if stated
      ; ID=BPQtoAGW 147.525 MHz ; Displayed by PORTS command
      ; TYPE=EXTERNAL  ; Calls an external module
      ; DLLNAME=BPQtoAGW.DLL ; Uses BPQtoAGW.DLL
      ; IOADDR=1F41  ; AGWPE Telnet port x'1F41' = 8001
      ; CHANNEL=A  ; AGWPE Port # A=1, B=2, etc
      ; QUALITY=192  ; Quality factor applied to node broadcasts heard on
      ;   ; this port, unless overridden by a locked route
      ;   ; entry. Setting to 0 stops node broadcasts
      ; MINQUAL=168  ; Entries in the nodes table with qualities greater or
      ;   ; equal to MINQUAL will be sent on this port. A value
      ;   ; of 0 sends everything.
      ; MAXFRAME=7  ; Max outstanding frames (1 thru 7)
      ; FRACK=5000  ; Level 2 timout in milliseconds
      ; RESPTIME=1000  ; Level 2 delayed ack timer in milliseconds
      ; RETRIES=5  ; Level 2 maximum retry value
      ; PACLEN=236  ; Default max packet length for this port
      ; UNPROTO=BPQP1  ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
      ; BCALL=N5IN-3  ; BTEXT call. unstated defaults to BBSCALL/APPL1CALL
      ; L3ONLY=0  ; 1=No user downlink connects on this port
      ; DIGIFLAG=1  ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
      ; DIGIPORT=0  ; Port on which to send digi'd frames (0 = same port)
      ; USERS=0  ; Maximum number of L2 sessions, 0 = no limit
      ;ENDPORT
      ; AX/IP/UDP port definition.
      PORT
       PORTNUM=2  ; Optional but sets port number if stated
       ID=AX/IP/UDP  ; Displayed by PORTS command
       TYPE=EXTERNAL  ; Calls an external module
       DLLNAME=BPQAXIP.DLL ; Uses BPQAXIP.DLL
       QUALITY=192  ; Quality factor applied to node broadcasts heard on
         ; this port, unless overridden by a locked route
         ; entry. Setting to 0 stops node broadcasts
       MINQUAL=168  ; Entries in the nodes table with qualities greater or
         ; equal to MINQUAL will be sent on this port. A value
         ; of 0 sends everything.
       MAXFRAME=7  ; Max outstanding frames (1 thru 7)
       FRACK=3000  ; Level 2 timout in milliseconds
       RESPTIME=1000  ; Level 2 delayed ack timer in milliseconds
       RETRIES=5  ; Level 2 maximum retry value
       PACLEN=236  ; Max = 236
      ENDPORT
      ROUTES:   ; Locked routes (31 maximum)
      ; CALLSIGN,QUALITY,PORT[,MAXFRAME,FRACK,PACLEN]
      ; The values in [...] if stated override the port defaults.
      VE2EDF-1,224,1  ; BPQ 147.525 MHz to production machine
      VE2EDF,223,2  ; BPQ AX/UPD to production machine
      VE2EDF-3,193,2  ; BPQ AX/UDP work office
      ***   ; Denotes end of locked routes
      ; Applications supported:
      ; The first three are reserved for BBS, HOST and REMOTE SYSOP. Five
      ; additional applications, up to 12 bytes each, can be defined as you wish.
      ; Applications beginning with a * are not shown in the valid commands display.
      APPLICATIONS=BBS
      ;DX,,*SYS ;BBS=DX, no host, remote sysop=*SYS
      ;Commented out as this configuration supports only a single application:
      ;APPL4CALL=N5IN-2
      ;APPL4ALIAS=PCTRF2
      ;APPL4QUAL=255
      ; APPLnCALL/APPLnALIAS defines 'call's and alias's associated with the
      ; positional parameters in APPLICATIONS=. N may assume values of 1,4,5,6,7,8
      ; as 2 and 3 are reserved for host and remote sysop. These calls/alias's
      ; announce themselves in node broadcasts unless their associated APPLnQUAL=0.
      ; APPL1CALL, APPL1ALIAS and APPL1QUAL, i.e. for n=1, replace the earlier
      ; defined BBSCALL/BBSALIAS/BBSQUAL if stated. The 'call's may include any of
      ; the characters A-Z 0-9, up to 6 characters in length, and optionally an
      ; SSID. Thus APPL4CALL=ABCDEF as well as APPL4CALL=AA0AAA-13 are valid. A
      ; connection to the APPLnCALL='call' will execute the nth positional parameter
      ; in the APPLICATIONS= string.
      ;
      ; AGWtoBPQ.exe includes an 'Applications Mask' created from the position of
      ; the 'application' in the APPLICATIONS= string. The mask is formed from the
      ; sum of the numbers 1,2,4,8,16,32,64,128. Thus in this configuraton the
      ; applications occupy positions 1 and 4, with associated masks of 1 and 8,
      ; which added together equal 9. Thus when using the AGWtoBPQ interface the
      ; 'Appl Mask' must be entered as 9.

      So i don't understand why
      but it's normal Im a french guy so i'm slow hihihiihih
       
      David
      VE2EDF

      To: BPQ32@yahoogroups.com
      From: ron_n5in@...
      Date: Wed, 30 Jan 2008 12:38:43 -0800
      Subject: Re: [BPQ32] config bpqcfg.txt with pk232 on fbbwin


      I had hoped someone with more knowledge of FBB would have replied to you, and perhaps they will.  However the configurations in  c:\Program Files\BPQ32\Examples\Medium can't be too far from what you are looking for.  The application happens to be a DX Cluster, but you could just change the applications parameter to:
      APPLICATION=BBS
      and you would be almost there.  You need to change the calls/aliases/IDMSG/BTEXT and such things which obviously need be changed to be applicable to you.  Of course your TNC must be set in KISS mode.

      Now as to configuring FBB, hopefully someone else here will step up....

      Ron, N5IN


      ----- Original Message ----
      From: david_linda_puncho <davidchadufaud@...>
      To: BPQ32@yahoogroups.com
      Sent: Wednesday, January 30, 2008 7:17:42 AM
      Subject: [BPQ32] config bpqcfg.txt with pk232 on fbbwin

      Hi and sorry for my english i'm french canadian
      Before i used fbb dos and pk232 so it worked well
      now i want install the last realease of FBB 7.01.35 with my pk232
      i read and read help on internet and i understand that i must use
      bpq32 for this use
      my fbb as 2 port one for forward on internet and the second with the
      pk232 connected on radio
      I read all your post but don't found the way
      so my question is:
      could you give me an exemple of the bpqcfg.txt where on the port 1
      is the forward internet and the port 2 the pk232 connected with bpq
      on the serial 2
      and i saw too i connect the pk232 before run fbb and bpq and with
      terminal windows itype in cmd mode kiss on on the pk232 and close
      terminal and run fbb
      so is it the right way ?
      thank's by advance
      sorry but i
      'm new on fbb windows on bpq32 and english hi hi hi
      best regard
      73
      David
      VE2EDF





    • Show all 6 messages in this topic