Loading ...
Sorry, an error occurred while loading the content.

10430Re: comports hex or decimal.

Expand Messages
  • James Mcdowall
    Apr 29, 2013
      Thank you both for the reply i get working on the ports now

      --- In BPQ32@yahoogroups.com, "Mike" <mmelnik1@...> wrote:
      >
      > Jim
      >
      >
      >
      > The following is a standard bpq32.cfg Kiss Port, the com port number to be
      > used is IOADDR=1 For Com 1
      >
      > =3 for Com 3 etc. the BAUD Rate is SPEED=
      >
      >
      >
      > Since you did not mention if your TNC'S were a multi port I assume you are
      > using 4 different TNC'S.
      >
      > If a TNC is a multiport TNC the IOADDR= will be the same for that TNC, you
      > only use Channel=A and Channel=B, etc.
      >
      >
      >
      > Remember to set the TNC'S in KISS mode before starting BPQ32 and/or Programs
      > used by BPQ32.
      >
      >
      >
      > If you have any problems let me know.
      >
      >
      >
      > 73
      >
      >
      >
      > PORT
      >
      > ID=145.030 MHz ; Displayed by PORTS command
      >
      > TYPE=ASYNC ; Port is RS232 Com, Kantronics 9612 Ch A
      >
      > PROTOCOL=KISS ; TNC is used in KISS mode
      >
      > NOKEEPALIVES=1 ; No Net Rom Polling
      >
      > FULLDUP=0 ; Only meaningful for KISS devices
      >
      > IOADDR=1 ; 1 = SERIAL PORT COM1 ETC.
      >
      > SPEED=9600 ; RS232 COM PORT SPEED
      >
      > CHANNEL=A ; Address if multichannel TNC
      >
      > PERSIST=225 ; PERSIST=256/(# of transmitters-1)
      >
      > SLOTTIME=100 ; CMSA interval timer in milliseconds
      >
      > TXDELAY=280 ; Transmit keyup delay in milliseconds
      >
      > TXTAIL=0 ; TX key down, in milliseconds, at
      > packet end
      >
      > QUALITY=192 ; Quality factor applied to node
      > broadcasts heard on
      >
      > ; this port, unless
      > overridden by a locked route
      >
      > ; entry. Setting to 0 stops
      > node broadcasts
      >
      > MINQUAL=168 ; Entries in the nodes table with
      > qualities greater or
      >
      > ; equal to MINQUAL will be
      > sent on this port. A value
      >
      > ; of 0 sends everything.
      >
      > MAXFRAME=2 ; Max outstanding frames (1 thru 7)
      >
      > FRACK=5000 ; Level 2 timout in milliseconds
      >
      > RESPTIME=2000 ; Level 2 delayed ack timer in
      > milliseconds
      >
      > RETRIES=6 ; Level 2 maximum retry value
      >
      > PACLEN=236 ; Default max packet length for this
      > port
      >
      > UNPROTO=BPQ Port 1 ; BTEXT Broadcast
      >
      > BCALL=N9PMO-2 ; BTEXT call. unstated defaults to
      > BBSCALL/APPL1CALL
      >
      > L3ONLY=0 ; 1=No user downlink connects on this
      > port
      >
      > DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
      >
      > DIGIPORT=0 ; Port on which to send digi'd frames
      > (0 = same port)
      >
      > USERS=0 ; Maximum number of L2 sessions, 0 =
      > no limit
      >
      > ENDPORT
      >
      >
      >
      > Mike N9PMO
      > <http://www.n9pmo.com> www.n9pmo.com
      >
      > -----Original Message-----
      > From: BPQ32@yahoogroups.com [mailto:BPQ32@yahoogroups.com] On Behalf Of
      > James Mcdowall
      > Sent: Monday, April 29, 2013 7:26 AM
      > To: BPQ32@yahoogroups.com
      > Subject: [BPQ32] comports hex or decimal.
      >
      >
      >
      >
      >
      > i am swapping my agwpe tnc ports so bpq connect to them direct
      > but not shure how
      >
      > com 1,3,4,6 are what there on now via agwpe
      > how do i write it into the cfg
      > there all at 9600
      > COMPORT=?
      > IOADDR=?
      > SPEED=?
      >
      > Cheers jim
      >
    • Show all 7 messages in this topic