Loading ...
Sorry, an error occurred while loading the content.

Re: [BCD396XT] Scanning Help

Expand Messages
  • Paul Opitz
    The answer depends on why ARMER isn t being scanned. It could be: * Enable the SQK assigned to the nearest ARMER site and disable the SQK assigned to the
    Message 1 of 17 , Jul 11, 2012
    View Source
    • 0 Attachment
      The answer depends on why ARMER isn't being scanned. It could be:
      * Enable the SQK assigned to the nearest ARMER site and disable the SQK
      assigned to the conventional system.
      * Unlock the site and lock out the conventional system.
      * Program the site correctly and delet the conventional system.
      * Enable the GQK assigned to the channel group(s) in the ARMER system.
      * Unlock the channel group(s) in the ARMER system.
      * Program some channels into a channel group in the ARMER system.
      * ...



      ________________________________
      From: Kristy <ziebarth715@...>
      To: BCD396XT@yahoogroups.com
      Sent: Wed, July 11, 2012 7:36:06 PM
      Subject: [BCD396XT] Scanning Help

       
      I've had my scanner for well over a year and never been able to figure it out. I
      have two groups: a conventional system and the ARMER group. My scanner will only
      scan the conventational group which has no channels in it. How do I get it to
      scan the ARMER system instead of the other one?





      [Non-text portions of this message have been removed]
    • Kristy
      I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can t get it to scan. What is SQK and
      Message 2 of 17 , Jul 13, 2012
      View Source
      • 0 Attachment
        I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?

        As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?



        --- In BCD396XT@yahoogroups.com, Paul Opitz <pmanu44@...> wrote:
        >
        > The answer depends on why ARMER isn't being scanned. It could be:
        > * Enable the SQK assigned to the nearest ARMER site and disable the SQK
        > assigned to the conventional system.
        > * Unlock the site and lock out the conventional system.
        > * Program the site correctly and delet the conventional system.
        > * Enable the GQK assigned to the channel group(s) in the ARMER system.
        > * Unlock the channel group(s) in the ARMER system.
        > * Program some channels into a channel group in the ARMER system.
        > * ...
        >
        >
        >
        > ________________________________
        > From: Kristy <ziebarth715@...>
        > To: BCD396XT@yahoogroups.com
        > Sent: Wed, July 11, 2012 7:36:06 PM
        > Subject: [BCD396XT] Scanning Help
        >
        >  
        > I've had my scanner for well over a year and never been able to figure it out. I
        > have two groups: a conventional system and the ARMER group. My scanner will only
        > scan the conventational group which has no channels in it. How do I get it to
        > scan the ARMER system instead of the other one?
        >
        >
        >
        >
        >
        > [Non-text portions of this message have been removed]
        >
      • Uniden UPMan
        If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.   SQK= System or Site Quick Key.
        Message 3 of 17 , Jul 13, 2012
        View Source
        • 0 Attachment
          If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
           
          SQK= System or Site Quick Key.
          GQK=Group Quick Key
           
          http://info.uniden.com/twiki/pub/publish/QuickKeys.html

          UpMan
          UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly


          >________________________________
          > From: Kristy <ziebarth715@...>
          >To: BCD396XT@yahoogroups.com
          >Sent: Friday, July 13, 2012 9:13 AM
          >Subject: [BCD396XT] Re: Scanning Help
          >
          >
          >

          >
          >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
          >
          >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
          >
          >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@...> wrote:
          >>
          >> The answer depends on why ARMER isn't being scanned. It could be:
          >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
          >> assigned to the conventional system.
          >> * Unlock the site and lock out the conventional system.
          >> * Program the site correctly and delet the conventional system.
          >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
          >> * Unlock the channel group(s) in the ARMER system.
          >> * Program some channels into a channel group in the ARMER system.
          >> * ...
          >>
          >>
          >>
          >> ________________________________
          >> From: Kristy <ziebarth715@...>
          >> To: mailto:BCD396XT%40yahoogroups.com
          >> Sent: Wed, July 11, 2012 7:36:06 PM
          >> Subject: [BCD396XT] Scanning Help
          >>
          >>  
          >> I've had my scanner for well over a year and never been able to figure it out. I
          >> have two groups: a conventional system and the ARMER group. My scanner will only
          >> scan the conventational group which has no channels in it. How do I get it to
          >> scan the ARMER system instead of the other one?
          >>
          >>
          >>
          >>
          >>
          >> [Non-text portions of this message have been removed]
          >>
          >
          >
          >
          >
          >

          [Non-text portions of this message have been removed]
        • Kristy
          I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won t
          Message 4 of 17 , Jul 13, 2012
          View Source
          • 0 Attachment
            I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.



            --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@...> wrote:
            >
            > If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
            >  
            > SQK= System or Site Quick Key.
            > GQK=Group Quick Key
            >  
            > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
            >
            > UpMan
            > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly
            >
            >
            > >________________________________
            > > From: Kristy <ziebarth715@...>
            > >To: BCD396XT@yahoogroups.com
            > >Sent: Friday, July 13, 2012 9:13 AM
            > >Subject: [BCD396XT] Re: Scanning Help
            > >
            > >
            > >
            > > 
            > >
            > >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
            > >
            > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
            > >
            > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
            > >>
            > >> The answer depends on why ARMER isn't being scanned. It could be:
            > >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
            > >> assigned to the conventional system.
            > >> * Unlock the site and lock out the conventional system.
            > >> * Program the site correctly and delet the conventional system.
            > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
            > >> * Unlock the channel group(s) in the ARMER system.
            > >> * Program some channels into a channel group in the ARMER system.
            > >> * ...
            > >>
            > >>
            > >>
            > >> ________________________________
            > >> From: Kristy <ziebarth715@>
            > >> To: mailto:BCD396XT%40yahoogroups.com
            > >> Sent: Wed, July 11, 2012 7:36:06 PM
            > >> Subject: [BCD396XT] Scanning Help
            > >>
            > >>  
            > >> I've had my scanner for well over a year and never been able to figure it out. I
            > >> have two groups: a conventional system and the ARMER group. My scanner will only
            > >> scan the conventational group which has no channels in it. How do I get it to
            > >> scan the ARMER system instead of the other one?
            > >>
            > >>
            > >>
            > >>
            > >>
            > >> [Non-text portions of this message have been removed]
            > >>
            > >
            > >
            > >
            > >
            > >
            >
            > [Non-text portions of this message have been removed]
            >
          • Lance
            your conventional system and your trunk system need to be separate. Is your trunk system locked out? Do you have a quick key assigned to it? ... [Non-text
            Message 5 of 17 , Jul 13, 2012
            View Source
            • 0 Attachment
              your conventional system and your trunk system need to be separate.

              Is your trunk system locked out?

              Do you have a quick key assigned to it?


              On Jul 13, 2012, at 9:32 AM, Kristy wrote:

              > I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.
              >
              > --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@...> wrote:
              > >
              > > If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
              > > �
              > > SQK= System or Site Quick Key.
              > > GQK=Group Quick Key
              > > �
              > > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
              > >
              > > UpMan
              > > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly
              > >
              > >
              > > >________________________________
              > > > From: Kristy <ziebarth715@...>
              > > >To: BCD396XT@yahoogroups.com
              > > >Sent: Friday, July 13, 2012 9:13 AM
              > > >Subject: [BCD396XT] Re: Scanning Help
              > > >
              > > >
              > > >
              > > >�
              > > >
              > > >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
              > > >
              > > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
              > > >
              > > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
              > > >>
              > > >> The��� answer depends on why ARMER isn't being scanned. It could be:
              > > >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
              > > >> assigned to the conventional system.
              > > >> * Unlock the site and lock out the conventional system.
              > > >> * Program the site correctly and delet the conventional system.
              > > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
              > > >> * Unlock the channel group(s) in the ARMER system.
              > > >> * Program some channels into a channel group in the ARMER system.
              > > >> * ...
              > > >>
              > > >>
              > > >>
              > > >> ________________________________
              > > >> From: Kristy <ziebarth715@>
              > > >> To: mailto:BCD396XT%40yahoogroups.com
              > > >> Sent: Wed, July 11, 2012 7:36:06 PM
              > > >> Subject: [BCD396XT] Scanning Help
              > > >>
              > > >> ���
              > > >> I've had my scanner for well over a year and never been able to figure it out. I
              > > >> have two groups: a conventional system and the ARMER group. My scanner will only
              > > >> scan the conventational group which has no channels in it. How do I get it to
              > > >> scan the ARMER system instead of the other one?
              > > >>
              > > >>
              > > >>
              > > >>
              > > >>
              > > >> [Non-text portions of this message have been removed]
              > > >>
              > > >
              > > >
              > > >
              > > >
              > > >
              > >
              > > [Non-text portions of this message have been removed]
              > >
              >
              >



              [Non-text portions of this message have been removed]
            • mygroups2007@comcast.net
              Kristy, Talkgroups are not frequencies. As UPMan said, you will need to enter the frequencies for the trunk system into the site. Ron in Eugene ... [Non-text
              Message 6 of 17 , Jul 13, 2012
              View Source
              • 0 Attachment
                Kristy,

                Talkgroups are not frequencies. As UPMan said, you will need to enter the frequencies for the trunk system into the site.

                Ron in Eugene



                On Jul 13, 2012, at 9:32 AM, Kristy wrote:

                > I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.
                > > >________________________________
                > > > From: Kristy <ziebarth715@...>
                > > >To: BCD396XT@yahoogroups.com
                > > >Sent: Friday, July 13, 2012 9:13 AM
                > > >Subject: [BCD396XT] Re: Scanning Help
                > > >
                > > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
                > > >



                [Non-text portions of this message have been removed]
              • Shawn Kurschner
                Kristy, where is the system? What city and state? ... -- *Shawn Kurschner* *(MCP, CSS, HDA, MCDST, MCTS)* *Manitowoc, WI USA * [Non-text portions of this
                Message 7 of 17 , Jul 13, 2012
                View Source
                • 0 Attachment
                  Kristy, where is the system? What city and state?

                  On Fri, Jul 13, 2012 at 10:32 AM, Kristy <ziebarth715@...> wrote:

                  > **
                  >
                  >
                  > I entered some frequencies in the Conventional System and it is now
                  > scanning those. But I have several talkgroups stored under the P-25 system
                  > but it won't can those. It will only scan the Conventional System.
                  >
                  > --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@...> wrote:
                  > >
                  > > If there are no frequencies in the system, then the scanner will have no
                  > ability to scan or receive it. Matters tremendously.
                  > > �
                  > > SQK= System or Site Quick Key.
                  > > GQK=Group Quick Key
                  > > �
                  > > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
                  > >
                  > > UpMan
                  > > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read
                  > before emailing me directly
                  > >
                  > >
                  > > >________________________________
                  > > > From: Kristy <ziebarth715@...>
                  > > >To: BCD396XT@yahoogroups.com
                  > > >Sent: Friday, July 13, 2012 9:13 AM
                  > > >Subject: [BCD396XT] Re: Scanning Help
                  > > >
                  > > >
                  > > >
                  > > >�
                  > > >
                  > > >I already have several channels programmed into the ARMER system. I can
                  > see them when I try to edit the system. But I can't get it to scan. What is
                  > SQK and GQK?
                  > > >
                  > > >As I was writing this, I noticed that there were no frequencies stored
                  > under the sit name. Would that matter?
                  > > >
                  > > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
                  > > >>
                  > > >> The��� answer depends on why ARMER isn't being scanned. It could be:
                  > > >> * Enable the SQK assigned to the nearest ARMER site and disable the
                  > SQK
                  > > >> assigned to the conventional system.
                  > > >> * Unlock the site and lock out the conventional system.
                  > > >> * Program the site correctly and delet the conventional system.
                  > > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
                  > > >> * Unlock the channel group(s) in the ARMER system.
                  > > >> * Program some channels into a channel group in the ARMER system.
                  > > >> * ...
                  > > >>
                  > > >>
                  > > >>
                  > > >> ________________________________
                  > > >> From: Kristy <ziebarth715@>
                  > > >> To: mailto:BCD396XT%40yahoogroups.com
                  > > >> Sent: Wed, July 11, 2012 7:36:06 PM
                  > > >> Subject: [BCD396XT] Scanning Help
                  > > >>
                  > > >> ���
                  > > >> I've had my scanner for well over a year and never been able to
                  > figure it out. I
                  > > >> have two groups: a conventional system and the ARMER group. My
                  > scanner will only
                  > > >> scan the conventational group which has no channels in it. How do I
                  > get it to
                  > > >> scan the ARMER system instead of the other one?
                  > > >>
                  > > >>
                  > > >>
                  > > >>
                  > > >>
                  > > >> [Non-text portions of this message have been removed]
                  > > >>
                  > > >
                  > > >
                  > > >
                  > > >
                  > > >
                  > >
                  > > [Non-text portions of this message have been removed]
                  > >
                  >
                  >
                  >



                  --

                  *Shawn Kurschner*

                  *(MCP, CSS, HDA, MCDST, MCTS)*

                  *Manitowoc, WI USA
                  *


                  [Non-text portions of this message have been removed]
                • Ron Aubry
                  Kristy, You should get a subscription to Radio Refferance first, then Download FREESCAN so you can program your system on the Computer. Third you need to buy
                  Message 8 of 17 , Jul 13, 2012
                  View Source
                  • 0 Attachment
                    Kristy, You should get a subscription to Radio Refferance first, then Download FREESCAN so you can program your system on the Computer. Third you need to buy or download the easy version of the Manual, and read, read, read, untill you understand how to enter your information and how to to program the differant types of systems. The 396XT is NOT a beginners scanner, and with the help of Radioreferance and the manual you will soon get the hang of it. Use Freescan to view differant typs of programs so you can see how they are programed. The cost of the Radio referance Membership is well worth the knowledge you will get from them not to mention the free programs. All you have to do is download and then uploAD TO YOUR SCANNER. Good Luck...

                    "Ask not of your friends , That which your friends could not ask of you."
                    God Bless....Ronald E Aubry




                    To: BCD396XT@yahoogroups.com
                    From: ziebarth715@...
                    Date: Fri, 13 Jul 2012 15:32:25 +0000
                    Subject: [BCD396XT] Re: Scanning Help


























                    I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.



                    --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@...> wrote:

                    >

                    > If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.

                    > �

                    > SQK= System or Site Quick Key.

                    > GQK=Group Quick Key

                    > �

                    > http://info.uniden.com/twiki/pub/publish/QuickKeys.html

                    >

                    > UpMan

                    > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly

                    >

                    >

                    > >________________________________

                    > > From: Kristy <ziebarth715@...>

                    > >To: BCD396XT@yahoogroups.com

                    > >Sent: Friday, July 13, 2012 9:13 AM

                    > >Subject: [BCD396XT] Re: Scanning Help

                    > >

                    > >

                    > >

                    > >�

                    > >

                    > >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?

                    > >

                    > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?

                    > >

                    > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:

                    > >>

                    > >> The��� answer depends on why ARMER isn't being scanned. It could be:

                    > >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK

                    > >> assigned to the conventional system.

                    > >> * Unlock the site and lock out the conventional system.

                    > >> * Program the site correctly and delet the conventional system.

                    > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.

                    > >> * Unlock the channel group(s) in the ARMER system.

                    > >> * Program some channels into a channel group in the ARMER system.

                    > >> * ...

                    > >>

                    > >>

                    > >>

                    > >> ________________________________

                    > >> From: Kristy <ziebarth715@>

                    > >> To: mailto:BCD396XT%40yahoogroups.com

                    > >> Sent: Wed, July 11, 2012 7:36:06 PM

                    > >> Subject: [BCD396XT] Scanning Help

                    > >>

                    > >> ���

                    > >> I've had my scanner for well over a year and never been able to figure it out. I

                    > >> have two groups: a conventional system and the ARMER group. My scanner will only

                    > >> scan the conventational group which has no channels in it. How do I get it to

                    > >> scan the ARMER system instead of the other one?

                    > >>

                    > >>

                    > >>

                    > >>

                    > >>

                    > >> [Non-text portions of this message have been removed]

                    > >>

                    > >

                    > >

                    > >

                    > >

                    > >

                    >

                    > [Non-text portions of this message have been removed]

                    >




















                    [Non-text portions of this message have been removed]
                  • Kristy
                    Minnesota, Isanti County
                    Message 9 of 17 , Jul 13, 2012
                    View Source
                    • 0 Attachment
                      Minnesota, Isanti County



                      --- In BCD396XT@yahoogroups.com, Shawn Kurschner <skurschner1672@...> wrote:
                      >
                      > Kristy, where is the system? What city and state?
                      >
                      > On Fri, Jul 13, 2012 at 10:32 AM, Kristy <ziebarth715@...> wrote:
                      >
                      > > **
                      > >
                      > >
                      > > I entered some frequencies in the Conventional System and it is now
                      > > scanning those. But I have several talkgroups stored under the P-25 system
                      > > but it won't can those. It will only scan the Conventional System.
                      > >
                      > > --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@> wrote:
                      > > >
                      > > > If there are no frequencies in the system, then the scanner will have no
                      > > ability to scan or receive it. Matters tremendously.
                      > > > Â
                      > > > SQK= System or Site Quick Key.
                      > > > GQK=Group Quick Key
                      > > > Â
                      > > > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
                      > > >
                      > > > UpMan
                      > > > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read
                      > > before emailing me directly
                      > > >
                      > > >
                      > > > >________________________________
                      > > > > From: Kristy <ziebarth715@>
                      > > > >To: BCD396XT@yahoogroups.com
                      > > > >Sent: Friday, July 13, 2012 9:13 AM
                      > > > >Subject: [BCD396XT] Re: Scanning Help
                      > > > >
                      > > > >
                      > > > >
                      > > > >Â
                      > > > >
                      > > > >I already have several channels programmed into the ARMER system. I can
                      > > see them when I try to edit the system. But I can't get it to scan. What is
                      > > SQK and GQK?
                      > > > >
                      > > > >As I was writing this, I noticed that there were no frequencies stored
                      > > under the sit name. Would that matter?
                      > > > >
                      > > > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
                      > > > >>
                      > > > >> The answer depends on why ARMER isn't being scanned. It could be:
                      > > > >> * Enable the SQK assigned to the nearest ARMER site and disable the
                      > > SQK
                      > > > >> assigned to the conventional system.
                      > > > >> * Unlock the site and lock out the conventional system.
                      > > > >> * Program the site correctly and delet the conventional system.
                      > > > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
                      > > > >> * Unlock the channel group(s) in the ARMER system.
                      > > > >> * Program some channels into a channel group in the ARMER system.
                      > > > >> * ...
                      > > > >>
                      > > > >>
                      > > > >>
                      > > > >> ________________________________
                      > > > >> From: Kristy <ziebarth715@>
                      > > > >> To: mailto:BCD396XT%40yahoogroups.com
                      > > > >> Sent: Wed, July 11, 2012 7:36:06 PM
                      > > > >> Subject: [BCD396XT] Scanning Help
                      > > > >>
                      > > > >> ÂÂ
                      > > > >> I've had my scanner for well over a year and never been able to
                      > > figure it out. I
                      > > > >> have two groups: a conventional system and the ARMER group. My
                      > > scanner will only
                      > > > >> scan the conventational group which has no channels in it. How do I
                      > > get it to
                      > > > >> scan the ARMER system instead of the other one?
                      > > > >>
                      > > > >>
                      > > > >>
                      > > > >>
                      > > > >>
                      > > > >> [Non-text portions of this message have been removed]
                      > > > >>
                      > > > >
                      > > > >
                      > > > >
                      > > > >
                      > > > >
                      > > >
                      > > > [Non-text portions of this message have been removed]
                      > > >
                      > >
                      > >
                      > >
                      >
                      >
                      >
                      > --
                      >
                      > *Shawn Kurschner*
                      >
                      > *(MCP, CSS, HDA, MCDST, MCTS)*
                      >
                      > *Manitowoc, WI USA
                      > *
                      >
                      >
                      > [Non-text portions of this message have been removed]
                      >
                    • Kristy
                      As far as I know its not locked out. And no quick key.
                      Message 10 of 17 , Jul 13, 2012
                      View Source
                      • 0 Attachment
                        As far as I know its not locked out. And no quick key.



                        --- In BCD396XT@yahoogroups.com, Lance <milcom_chaser@...> wrote:
                        >
                        > your conventional system and your trunk system need to be separate.
                        >
                        > Is your trunk system locked out?
                        >
                        > Do you have a quick key assigned to it?
                        >
                        >
                        > On Jul 13, 2012, at 9:32 AM, Kristy wrote:
                        >
                        > > I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.
                        > >
                        > > --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@> wrote:
                        > > >
                        > > > If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
                        > > > Â
                        > > > SQK= System or Site Quick Key.
                        > > > GQK=Group Quick Key
                        > > > Â
                        > > > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
                        > > >
                        > > > UpMan
                        > > > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly
                        > > >
                        > > >
                        > > > >________________________________
                        > > > > From: Kristy <ziebarth715@>
                        > > > >To: BCD396XT@yahoogroups.com
                        > > > >Sent: Friday, July 13, 2012 9:13 AM
                        > > > >Subject: [BCD396XT] Re: Scanning Help
                        > > > >
                        > > > >
                        > > > >
                        > > > >Â
                        > > > >
                        > > > >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
                        > > > >
                        > > > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
                        > > > >
                        > > > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
                        > > > >>
                        > > > >> The answer depends on why ARMER isn't being scanned. It could be:
                        > > > >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
                        > > > >> assigned to the conventional system.
                        > > > >> * Unlock the site and lock out the conventional system.
                        > > > >> * Program the site correctly and delet the conventional system.
                        > > > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
                        > > > >> * Unlock the channel group(s) in the ARMER system.
                        > > > >> * Program some channels into a channel group in the ARMER system.
                        > > > >> * ...
                        > > > >>
                        > > > >>
                        > > > >>
                        > > > >> ________________________________
                        > > > >> From: Kristy <ziebarth715@>
                        > > > >> To: mailto:BCD396XT%40yahoogroups.com
                        > > > >> Sent: Wed, July 11, 2012 7:36:06 PM
                        > > > >> Subject: [BCD396XT] Scanning Help
                        > > > >>
                        > > > >> ÂÂ
                        > > > >> I've had my scanner for well over a year and never been able to figure it out. I
                        > > > >> have two groups: a conventional system and the ARMER group. My scanner will only
                        > > > >> scan the conventational group which has no channels in it. How do I get it to
                        > > > >> scan the ARMER system instead of the other one?
                        > > > >>
                        > > > >>
                        > > > >>
                        > > > >>
                        > > > >>
                        > > > >> [Non-text portions of this message have been removed]
                        > > > >>
                        > > > >
                        > > > >
                        > > > >
                        > > > >
                        > > > >
                        > > >
                        > > > [Non-text portions of this message have been removed]
                        > > >
                        > >
                        > >
                        >
                        >
                        >
                        > [Non-text portions of this message have been removed]
                        >
                      • Kristy
                        I had a subscription to RR but it expired. That is how I programmed the scanner when I purchased it. I still have all the info saved on my computer as far as
                        Message 11 of 17 , Jul 13, 2012
                        View Source
                        • 0 Attachment
                          I had a subscription to RR but it expired. That is how I programmed the scanner when I purchased it. I still have all the info saved on my computer as far as the talkgroup ID's. But my scanner just won't scan that system no matter what I do.

                          I even tried going through the Uniden manual and recreated a system with the ID's and it still won't scan.


                          --- In BCD396XT@yahoogroups.com, Ron Aubry <trkntrlrman@...> wrote:
                          >
                          >
                          >
                          >
                          >
                          > Kristy, You should get a subscription to Radio Refferance first, then Download FREESCAN so you can program your system on the Computer. Third you need to buy or download the easy version of the Manual, and read, read, read, untill you understand how to enter your information and how to to program the differant types of systems. The 396XT is NOT a beginners scanner, and with the help of Radioreferance and the manual you will soon get the hang of it. Use Freescan to view differant typs of programs so you can see how they are programed. The cost of the Radio referance Membership is well worth the knowledge you will get from them not to mention the free programs. All you have to do is download and then uploAD TO YOUR SCANNER. Good Luck...
                          >
                          > "Ask not of your friends , That which your friends could not ask of you."
                          > God Bless....Ronald E Aubry
                          >
                          >
                          >
                          >
                          > To: BCD396XT@yahoogroups.com
                          > From: ziebarth715@...
                          > Date: Fri, 13 Jul 2012 15:32:25 +0000
                          > Subject: [BCD396XT] Re: Scanning Help
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          > I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.
                          >
                          >
                          >
                          > --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@> wrote:
                          >
                          > >
                          >
                          > > If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
                          >
                          > > Â
                          >
                          > > SQK= System or Site Quick Key.
                          >
                          > > GQK=Group Quick Key
                          >
                          > > Â
                          >
                          > > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
                          >
                          > >
                          >
                          > > UpMan
                          >
                          > > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly
                          >
                          > >
                          >
                          > >
                          >
                          > > >________________________________
                          >
                          > > > From: Kristy <ziebarth715@>
                          >
                          > > >To: BCD396XT@yahoogroups.com
                          >
                          > > >Sent: Friday, July 13, 2012 9:13 AM
                          >
                          > > >Subject: [BCD396XT] Re: Scanning Help
                          >
                          > > >
                          >
                          > > >
                          >
                          > > >
                          >
                          > > >Â
                          >
                          > > >
                          >
                          > > >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
                          >
                          > > >
                          >
                          > > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
                          >
                          > > >
                          >
                          > > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
                          >
                          > > >>
                          >
                          > > >> The answer depends on why ARMER isn't being scanned. It could be:
                          >
                          > > >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
                          >
                          > > >> assigned to the conventional system.
                          >
                          > > >> * Unlock the site and lock out the conventional system.
                          >
                          > > >> * Program the site correctly and delet the conventional system.
                          >
                          > > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
                          >
                          > > >> * Unlock the channel group(s) in the ARMER system.
                          >
                          > > >> * Program some channels into a channel group in the ARMER system.
                          >
                          > > >> * ...
                          >
                          > > >>
                          >
                          > > >>
                          >
                          > > >>
                          >
                          > > >> ________________________________
                          >
                          > > >> From: Kristy <ziebarth715@>
                          >
                          > > >> To: mailto:BCD396XT%40yahoogroups.com
                          >
                          > > >> Sent: Wed, July 11, 2012 7:36:06 PM
                          >
                          > > >> Subject: [BCD396XT] Scanning Help
                          >
                          > > >>
                          >
                          > > >> ÂÂ
                          >
                          > > >> I've had my scanner for well over a year and never been able to figure it out. I
                          >
                          > > >> have two groups: a conventional system and the ARMER group. My scanner will only
                          >
                          > > >> scan the conventational group which has no channels in it. How do I get it to
                          >
                          > > >> scan the ARMER system instead of the other one?
                          >
                          > > >>
                          >
                          > > >>
                          >
                          > > >>
                          >
                          > > >>
                          >
                          > > >>
                          >
                          > > >> [Non-text portions of this message have been removed]
                          >
                          > > >>
                          >
                          > > >
                          >
                          > > >
                          >
                          > > >
                          >
                          > > >
                          >
                          > > >
                          >
                          > >
                          >
                          > > [Non-text portions of this message have been removed]
                          >
                          > >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          >
                          > [Non-text portions of this message have been removed]
                          >
                        • MCH
                          As others have mentioned, the site frequencies are *required* in order to scan a trunk system. You cannot scan it just with the TGIDs. Joe M.
                          Message 12 of 17 , Jul 13, 2012
                          View Source
                          • 0 Attachment
                            As others have mentioned, the site frequencies are *required* in order
                            to scan a trunk system. You cannot scan it just with the TGIDs.

                            Joe M.

                            Kristy wrote:
                            > I had a subscription to RR but it expired. That is how I programmed the scanner when I purchased it. I still have all the info saved on my computer as far as the talkgroup ID's. But my scanner just won't scan that system no matter what I do.
                            >
                            > I even tried going through the Uniden manual and recreated a system with the ID's and it still won't scan.
                            >
                            >
                            > --- In BCD396XT@yahoogroups.com, Ron Aubry <trkntrlrman@...> wrote:
                            >>
                            >>
                            >>
                            >>
                            >> Kristy, You should get a subscription to Radio Refferance first, then Download FREESCAN so you can program your system on the Computer. Third you need to buy or download the easy version of the Manual, and read, read, read, untill you understand how to enter your information and how to to program the differant types of systems. The 396XT is NOT a beginners scanner, and with the help of Radioreferance and the manual you will soon get the hang of it. Use Freescan to view differant typs of programs so you can see how they are programed. The cost of the Radio referance Membership is well worth the knowledge you will get from them not to mention the free programs. All you have to do is download and then uploAD TO YOUR SCANNER. Good Luck...
                            >>
                            >> "Ask not of your friends , That which your friends could not ask of you."
                            >> God Bless....Ronald E Aubry
                            >>
                            >>
                            >>
                            >>
                            >> To: BCD396XT@yahoogroups.com
                            >> From: ziebarth715@...
                            >> Date: Fri, 13 Jul 2012 15:32:25 +0000
                            >> Subject: [BCD396XT] Re: Scanning Help
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >> I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.
                            >>
                            >>
                            >>
                            >> --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@> wrote:
                            >>
                            >>> If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
                            >>> Â
                            >>> SQK= System or Site Quick Key.
                            >>> GQK=Group Quick Key
                            >>> Â
                            >>> http://info.uniden.com/twiki/pub/publish/QuickKeys.html
                            >>> UpMan
                            >>> UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly
                            >>>> ________________________________
                            >>>> From: Kristy <ziebarth715@>
                            >>>> To: BCD396XT@yahoogroups.com
                            >>>> Sent: Friday, July 13, 2012 9:13 AM
                            >>>> Subject: [BCD396XT] Re: Scanning Help
                            >>>>
                            >>>> Â
                            >>>> I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
                            >>>> As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
                            >>>> --- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
                            >>>>> The answer depends on why ARMER isn't being scanned. It could be:
                            >>>>> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
                            >>>>> assigned to the conventional system.
                            >>>>> * Unlock the site and lock out the conventional system.
                            >>>>> * Program the site correctly and delet the conventional system.
                            >>>>> * Enable the GQK assigned to the channel group(s) in the ARMER system.
                            >>>>> * Unlock the channel group(s) in the ARMER system.
                            >>>>> * Program some channels into a channel group in the ARMER system.
                            >>>>> * ...
                            >>>>> ________________________________
                            >>>>> From: Kristy <ziebarth715@>
                            >>>>> To: mailto:BCD396XT%40yahoogroups.com
                            >>>>> Sent: Wed, July 11, 2012 7:36:06 PM
                            >>>>> Subject: [BCD396XT] Scanning Help
                            >>>>> ÂÂ
                            >>>>> I've had my scanner for well over a year and never been able to figure it out. I
                            >>>>> have two groups: a conventional system and the ARMER group. My scanner will only
                            >>>>> scan the conventational group which has no channels in it. How do I get it to
                            >>>>> scan the ARMER system instead of the other one?
                            >>>>> [Non-text portions of this message have been removed]
                            >>>>
                            >>>>
                            >>>>
                            >>> [Non-text portions of this message have been removed]
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >>
                            >> [Non-text portions of this message have been removed]
                            >>
                            >
                            >
                            >
                            >
                            > ------------------------------------
                            >
                            > Yahoo! Groups Links
                            >
                            >
                            >
                            >
                            > ------------------------------------------------------------------------
                            >
                            >
                            > No virus found in this incoming message.
                            > Checked by AVG - www.avg.com
                            > Version: 9.0.930 / Virus Database: 2437.1.1/5129 - Release Date: 07/13/12 02:34:00
                            >
                          • Lance
                            Assign that system a quick key of your choice. You can assign that at the system level via the menu key. Do the sites for your system have frequencies
                            Message 13 of 17 , Jul 13, 2012
                            View Source
                            • 0 Attachment
                              Assign that system a quick key of your choice.

                              You can assign that at the system level via the menu key.

                              Do the sites for your system have frequencies programmed into them?




                              On Jul 13, 2012, at 12:10 PM, Kristy wrote:

                              > As far as I know its not locked out. And no quick key.
                              >
                              > --- In BCD396XT@yahoogroups.com, Lance <milcom_chaser@...> wrote:
                              > >
                              > > your conventional system and your trunk system need to be separate.
                              > >
                              > > Is your trunk system locked out?
                              > >
                              > > Do you have a quick key assigned to it?
                              > >
                              > >
                              > > On Jul 13, 2012, at 9:32 AM, Kristy wrote:
                              > >
                              > > > I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.
                              > > >
                              > > > --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@> wrote:
                              > > > >
                              > > > > If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
                              > > > > �
                              > > > > SQK= System or Site Quick Key.
                              > > > > GQK=Group Quick Key
                              > > > > �
                              > > > > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
                              > > > >
                              > > > > UpMan
                              > > > > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly
                              > > > >
                              > > > >
                              > > > > >________________________________
                              > > > > > From: Kristy <ziebarth715@>
                              > > > > >To: BCD396XT@yahoogroups.com
                              > > > > >Sent: Friday, July 13, 2012 9:13 AM
                              > > > > >Subject: [BCD396XT] Re: Scanning Help
                              > > > > >
                              > > > > >
                              > > > > >
                              > > > > >�
                              > > > > >
                              > > > > >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
                              > > > > >
                              > > > > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
                              > > > > >
                              > > > > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
                              > > > > >>
                              > > > > >> The��� answer depends on why ARMER isn't being scanned. It could be:
                              > > > > >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
                              > > > > >> assigned to the conventional system.
                              > > > > >> * Unlock the site and lock out the conventional system.
                              > > > > >> * Program the site correctly and delet the conventional system.
                              > > > > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
                              > > > > >> * Unlock the channel group(s) in the ARMER system.
                              > > > > >> * Program some channels into a channel group in the ARMER system.
                              > > > > >> * ...
                              > > > > >>
                              > > > > >>
                              > > > > >>
                              > > > > >> ________________________________
                              > > > > >> From: Kristy <ziebarth715@>
                              > > > > >> To: mailto:BCD396XT%40yahoogroups.com
                              > > > > >> Sent: Wed, July 11, 2012 7:36:06 PM
                              > > > > >> Subject: [BCD396XT] Scanning Help
                              > > > > >>
                              > > > > >> ���
                              > > > > >> I've had my scanner for well over a year and never been able to figure it out. I
                              > > > > >> have two groups: a conventional system and the ARMER group. My scanner will only
                              > > > > >> scan the conventational group which has no channels in it. How do I get it to
                              > > > > >> scan the ARMER system instead of the other one?
                              > > > > >>
                              > > > > >>
                              > > > > >>
                              > > > > >>
                              > > > > >>
                              > > > > >> [Non-text portions of this message have been removed]
                              > > > > >>
                              > > > > >
                              > > > > >
                              > > > > >
                              > > > > >
                              > > > > >
                              > > > >
                              > > > > [Non-text portions of this message have been removed]
                              > > > >
                              > > >
                              > > >
                              > >
                              > >
                              > >
                              > > [Non-text portions of this message have been removed]
                              > >
                              >
                              >



                              [Non-text portions of this message have been removed]
                            • Doug Johnson
                              Gidday Ron, You certainly hit the nail right on the head. I think what you said should be put on our web page and also in the email when they join as this
                              Message 14 of 17 , Jul 13, 2012
                              View Source
                              • 0 Attachment
                                Gidday Ron,



                                You certainly hit the nail right on the head.


                                I think what you said should be put on our web page and also in the email when

                                they join as this would stop a lot of unnecessary emails.



                                These scanners require alot of effort and research to understand them and get them going.

                                Definitely not a beginners scanner !


                                Regards,

                                Doug VK2XLJ


                                > To: bcd396xt@yahoogroups.com
                                > From: trkntrlrman@...
                                > Date: Fri, 13 Jul 2012 10:35:21 -0700
                                > Subject: RE: [BCD396XT] Re: Scanning Help
                                >
                                >
                                >
                                >
                                >
                                > Kristy, You should get a subscription to Radio Refferance first, then Download FREESCAN so you can program your system on the Computer. Third you need to buy or download the easy version of the Manual, and read, read, read, untill you understand how to enter your information and how to to program the differant types of systems. The 396XT is NOT a beginners scanner, and with the help of Radioreferance and the manual you will soon get the hang of it. Use Freescan to view differant typs of programs so you can see how they are programed. The cost of the Radio referance Membership is well worth the knowledge you will get from them not to mention the free programs. All you have to do is download and then uploAD TO YOUR SCANNER. Good Luck...
                                >
                                > "Ask not of your friends , That which your friends could not ask of you."
                                > God Bless....Ronald E Aubry
                                >
                                >
                                >
                                >
                                > To: BCD396XT@yahoogroups.com
                                > From: ziebarth715@...
                                > Date: Fri, 13 Jul 2012 15:32:25 +0000
                                > Subject: [BCD396XT] Re: Scanning Help
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                > I entered some frequencies in the Conventional System and it is now scanning those. But I have several talkgroups stored under the P-25 system but it won't can those. It will only scan the Conventional System.
                                >
                                >
                                >
                                > --- In BCD396XT@yahoogroups.com, Uniden UPMan <uniden.upman@...> wrote:
                                >
                                > >
                                >
                                > > If there are no frequencies in the system, then the scanner will have no ability to scan or receive it. Matters tremendously.
                                >
                                > > �
                                >
                                > > SQK= System or Site Quick Key.
                                >
                                > > GQK=Group Quick Key
                                >
                                > > �
                                >
                                > > http://info.uniden.com/twiki/pub/publish/QuickKeys.html
                                >
                                > >
                                >
                                > > UpMan
                                >
                                > > UpMan FAQ: http://info.uniden.com/UnidenMan4/UpMan -- Please read before emailing me directly
                                >
                                > >
                                >
                                > >
                                >
                                > > >________________________________
                                >
                                > > > From: Kristy <ziebarth715@...>
                                >
                                > > >To: BCD396XT@yahoogroups.com
                                >
                                > > >Sent: Friday, July 13, 2012 9:13 AM
                                >
                                > > >Subject: [BCD396XT] Re: Scanning Help
                                >
                                > > >
                                >
                                > > >
                                >
                                > > >
                                >
                                > > >�
                                >
                                > > >
                                >
                                > > >I already have several channels programmed into the ARMER system. I can see them when I try to edit the system. But I can't get it to scan. What is SQK and GQK?
                                >
                                > > >
                                >
                                > > >As I was writing this, I noticed that there were no frequencies stored under the sit name. Would that matter?
                                >
                                > > >
                                >
                                > > >--- In mailto:BCD396XT%40yahoogroups.com, Paul Opitz <pmanu44@> wrote:
                                >
                                > > >>
                                >
                                > > >> The��� answer depends on why ARMER isn't being scanned. It could be:
                                >
                                > > >> * Enable the SQK assigned to the nearest ARMER site and disable the SQK
                                >
                                > > >> assigned to the conventional system.
                                >
                                > > >> * Unlock the site and lock out the conventional system.
                                >
                                > > >> * Program the site correctly and delet the conventional system.
                                >
                                > > >> * Enable the GQK assigned to the channel group(s) in the ARMER system.
                                >
                                > > >> * Unlock the channel group(s) in the ARMER system.
                                >
                                > > >> * Program some channels into a channel group in the ARMER system.
                                >
                                > > >> * ...
                                >
                                > > >>
                                >
                                > > >>
                                >
                                > > >>
                                >
                                > > >> ________________________________
                                >
                                > > >> From: Kristy <ziebarth715@>
                                >
                                > > >> To: mailto:BCD396XT%40yahoogroups.com
                                >
                                > > >> Sent: Wed, July 11, 2012 7:36:06 PM
                                >
                                > > >> Subject: [BCD396XT] Scanning Help
                                >
                                > > >>
                                >
                                > > >> ���
                                >
                                > > >> I've had my scanner for well over a year and never been able to figure it out. I
                                >
                                > > >> have two groups: a conventional system and the ARMER group. My scanner will only
                                >
                                > > >> scan the conventational group which has no channels in it. How do I get it to
                                >
                                > > >> scan the ARMER system instead of the other one?
                                >
                                > > >>
                                >
                                > > >>
                                >
                                > > >>
                                >
                                > > >>
                                >
                                > > >>
                                >
                                > > >> [Non-text portions of this message have been removed]
                                >
                                > > >>
                                >
                                > > >
                                >
                                > > >
                                >
                                > > >
                                >
                                > > >
                                >
                                > > >
                                >
                                > >
                                >
                                > > [Non-text portions of this message have been removed]
                                >
                                > >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                >
                                > [Non-text portions of this message have been removed]
                                >
                                >
                                >
                                > ------------------------------------
                                >
                                > Yahoo! Groups Links
                                >
                                >
                                >


                                [Non-text portions of this message have been removed]
                              • Kristy
                                Thank you everyone for your help today. I renewed my subscription to RR. I deleted all the systems I had on my scanner and started from scratch. So far it
                                Message 15 of 17 , Jul 13, 2012
                                View Source
                                • 0 Attachment
                                  Thank you everyone for your help today. I renewed my subscription to RR. I deleted all the systems I had on my scanner and started from scratch. So far it seems to be working. Haven't heard my local county yet but I'll give it some time. Thanks again!



                                  --- In BCD396XT@yahoogroups.com, "Kristy" <ziebarth715@...> wrote:
                                  >
                                  > I've had my scanner for well over a year and never been able to figure it out. I have two groups: a conventional system and the ARMER group. My scanner will only scan the conventational group which has no channels in it. How do I get it to scan the ARMER system instead of the other one?
                                  >
                                • Gail Wisher
                                  It has been reported that OPD has sloved one of its problems with the p25 system . An AT and T transmiting any near the xmtr site was causing interference and
                                  Message 16 of 17 , Sep 8, 2012
                                  View Source
                                  • 0 Attachment
                                    It has been reported that OPD has sloved one of its problems with the p25 system . An AT and T transmiting any near the xmtr site was causing interference and once it was removed the system proformence improved.




                                    Switch to: Text-Only, Daily Digest • Unsubscribe • Terms of Use
                                    .



                                    [Non-text portions of this message have been removed]
                                  Your message has been successfully submitted and would be delivered to recipients shortly.