Loading ...
Sorry, an error occurred while loading the content.

Messages List

21487

Re: Poly 318 factory cast 4 barrel intake maifold & Holley electric

I run the Bouchellon as well and Rich is using the Lokar on our 64's Sent from Yahoo Mail on Android On Sat, Jun 24, 2017 at 15:15, bob derlunas
James Rice
Jun 24
#21487
 
21486

Re: Poly 318 factory cast 4 barrel intake maifold & Holley electric

I used Bouchellon Performance for the necessary parts. Some use Lokar. What year car is this going on?   On Saturday, June 24, 2017 2:55 PM, "roy589@...
bob derlunas
Jun 24
#21486
 
21485

Re: Poly 318 factory cast 4 barrel intake maifold & Holley electric

Hi Bob, I think I just purchased your manifold on ebay? Any suggestion on linkage adaption or other notes. I will be replacing my stock 2 barrel manifold. Much
roy589
Jun 24
#21485
 
21484

Re: Has anybody tried Corian for a carb spacer?

Isn't Corian like a thick veneer over OSB? My only concern would be delamination of surfaces exposed to the fuel/air mix which I suppose it can be alleviated
twincamracing
Jun 24
#21484
 
21483

Re: Has anybody tried Corian for a carb spacer?

This is probably silly and obvious o y’all, was to m when I finally figured it out. If you’ve got a wooden spacer adaptor for a Holley with electric choke,
joel.kelly14
Jun 23
#21483
This message has attachments
  • PNG
    253 Bytes
21482

Re: 1966 Poly 318 Core

Thank you Lance! Have a great weekend. Gary
polystroker
Jun 23
#21482
 
21481

Re: Has anybody tried Corian for a carb spacer?

Aw shucks, didn't know about the cracking part Sent from Yahoo Mail on Android On Fri, 23 Jun 2017 at 9:20 pm, Richard Kinsley leroarkinsley@...
Richard Kinsley
Jun 23
#21481
 
21480

Re: Has anybody tried Corian for a carb spacer?

That sounds like a great idea to me! Sent from Yahoo Mail on Android On Fri, 23 Jun 2017 at 6:30 pm, '. .' jchistia@...
Richard Kinsley
Jun 23
#21480
 
21479

1966 Poly 318 Core

Hey fruit-loops! I have a 1966 poly 318 complete engine, spins free. It has low compression on one of the cylinders (90) Great candidate for rebuild! Located
Semones Lance
Jun 23
#21479
 
21478

Re: Has anybody tried Corian for a carb spacer?

The best insulator, superior to phenolic resin, is laminated hardwood. Or you may use a quality grade plywood available at all Lowes/Home Depot...home
glpavlovich@...
Jun 23
#21478
 
21477

Re: Has anybody tried Corian for a carb spacer?

It cracks under extend heat cycles! Sent from Yahoo Mail on Android On Fri, Jun 23, 2017 at 7:30 PM, '. .' jchistia@...
tony brunelle
Jun 23
#21477
 
21476

Has anybody tried Corian for a carb spacer?

With all of the sink cutouts scrap, has anybody tried using Corian for a carb spacer? On 05/24/2017 4:23 PM, Richard Kinsley
. .
Jun 23
#21476
 
21475

Re: 4 Barrel Swap

Tim, Did you recieve a Poly SS-X Installation tips page with your manifold? If not I could send a copy of mine. I have not yet installed my manifold because
John Groth
Jun 23
#21475
 
21474

Re: Hi all, anyone running fuel injection on their poly? I recently

Funny you mentioned that. Just got home from visiting my daughter 60 miles away. I stuck a piece of cardboard in front of the radiator and drove all the way
Jason Chisholm
Jun 18
#21474
 
21473

Re: Hi all, anyone running fuel injection on their poly? I recently

Hi Jason,    Sounds like it's time to get on the phone with FiTech technical support.  In the meantime, how about blocking the radiator to get the running
Joel Kelly
Jun 18
#21473
 
View First Topic Go to View Last Topic