All you North Eastern modellers, What type/brand/color paint do paint the base of your layouts prior to putting on ground cover and what type/brand/color of...
Hello Zeds, Hope this message gets out to you as my ISP provider has had some nasty problems with outgoing email for the past 24 hours. Here is the original...
... GeDe, From my experience with the Relco I'll try to answer two of your questions. 2) I would not use any of the capacitors that are included with the ...
Michael, This "sterilization" topic surfaced some months ago, but if most are like me
they forgot. So thanks again for bringing up these excellent points...
Wendy, Your proposal to quote some of us in your upcoming article reminds me of a
line from the movie "Support your local Sheriff". The town drunk, played by...
Hi Wendy,all, I have no problem with it. Mine are NOT original ideas! Good luck and don't drink and drive,...trains! ;-) Dr Dirt. ... From: Wendy Harlow To:...
Jeffrey, Thanks for the tips on getting "earthy". Now I am going to have to stop
along the highway up near Salem and get me some of that red earth and go to...
Robert, I just now realized that I said PRR instead of ARR. I must be older than I
think :o) Loren ... From: bobfage2000 Date: 09/05/06 01:47:01 To:...
Don, Do what all the time?........dribble and drool like Jeffrey mentions, or you
talking about something else...........wink! Isn't it amazing how many...
Kevin, You must have a potty mouth, because you have a "dirty mind"........wink! Question, doesn't the fine dirt almost disolve and become mud when you put
it...
Can anyone give me any information about the Markin "art" cars? I have seen them on the auction site and purchased a couple that appealed to me, but the...
In reviewing the October issue of MR, I think it is safe to say Z is being considered a main stream scale. First is their National Trains Show special. The ...
Now Ed, You know perfectly well that if we don't get free packaging with every
turnout, then the garbage truck drivers won't pick up enough garbage to
warrent...
The GP35 has a bit more room under the hood than the SD70, but neither is wide enough for the current decoders. Still need to get my hands on the new...
Been a rainy day as the tropical storm that came up the east coast this week comes inland over North Carolina and Virginia and proceeds through PA and Western...
Hi all I see 50% would use 6mm with Z Scale 21.43% would not use 6mm with Z Scale 28.57% are unsure if they would or not Here some info anout 6mm to help...
There was discussion a while back about someone perhaps picking up the wiring harness ball when Bill K announced his retirement. Does anyone know anything else...
Hi all, well thank ye thank ye MTL and Joe D. for the beautiful CSX boxcar. I will be purchasing quite a few of these beauties. Hope you do Chessie system...
Hi Gang, This month's Ztrack is landing in mailboxes across the world and readers will enjoy another informative and entertaining issue. In addition to the...
Hi, everyone, Just an intro - I'm interested in N gauge and possibly Z. Is there *anything* in the way of Japanese prototypes in Z or a gauge smaller than N? ...
Anyone have any hits and tips on cutting window detail into plasticard (styrene sheet) at Z scale sizes. With bigger scales its not too hard to cut a cross and...
Jim, A post of info later on after I figure where I put my eyeballs. I caught
the red eye out of Anchorage this morning at 1am. They don't call it the
red...
Hi All Sitting on the other side of the pond, I'm receiving the post from the group in bundles. It gives me a good overview of the ongoing discussions, but is...
Received my copy of Ztrack today. Just spent most of evening devouring it. Very nice article on Japanese Z from Harald Thom-Freudenreich looking forward to the...
Hi, Chat is open on Z Cetral Station, beginning at 8pm tonight, EST, Z you there. No 'moderator ' questions will be entertained. I will entertain Alen Cox'...
Hi All, I sadly say I'm stepping down from being a moderator of Z Scale, this group, due to personal reasons. I will continue to be a member as long as our...
Okay, since posting the HTM announcement, a few keened eye observers have noted the return of Kluz Originals on our product sheet. In 1994, I came out with a...
