Kevin NB7O wrote... ... That explains that - hi! ... There may not be an issue. I could just be that there are no nearby digipeaters. ... Possibly, but when...
7333
akamr.fixit
May 2, 2009 3:46 am
Please help! I cannot find a wiring diagram to connect the RG-45 mic jack on my Motorola MaxTrac radio to the DB9 on the OT2m. I know that I will need to draw...
7334
James Ewen
james_ewen
May 2, 2009 6:47 am
Try the accessory plug on the back. There's a pin out diagram in the wiki. James ... -- Sent from my mobile device...
7335
Bernie Roche
chevalier137
May 2, 2009 8:52 am
Hi: Does your Maxtrac have the 5-pin or the 12-pin accessory connector at the back? I have the schematic for using the 12-pin, and the connectors are...
7336
Bernie Roche
chevalier137
May 2, 2009 8:52 am
Hi: I forgot to attach the schematic to my first email...here it is. Best Wishes, Bernie VE3OTR ... The following section of this message contains a file...
7337
n5lrq
May 2, 2009 5:40 pm
here is a link to info on the maxtrac interfacing that might help. http://www.repeater-builder.com/maxtrac/max-rptr-int.html ... From: "akamr.fixit"...
7338
Bruce W. Martin
kq4tv
May 2, 2009 6:09 pm
I have a Nuvi 350 and purchased the 010-10813-00 Mini-B Data Cable to hook it up to a DR-135 w/T2-135 installed. Works great. Purchased a GTRANS to hook up the...
7339
Mike Henry
wd5mhz
May 3, 2009 12:53 am
Hello i have the tracker 2 set up as a digi i have noticed a some people running wide 2-1 my digi is 2-2 what whould happen if i have wide2-1,wide2-2? ...
7340
Keith VE7GDH
ve7gdh
May 3, 2009 1:57 am
Mike WD5MHZ wrote... ... Are you talking about your own outgoing path? Something like a KPC3+ is capable of using multiple paths... e.g. one beacon per hour...
7341
Richard Braddock
ae4bp
May 3, 2009 3:59 pm
I am also looking for an answer to this question. The default on power up in NOT in data mode. I am also not able to save this in the memory location. It would...
7342
Richard Bauer
rk911
May 3, 2009 4:13 pm
hmmm. i just powered off my DR-135T mkIII and then powered it back up and it came back on in data mode. i then disconnected it from the camper's battery and...
7343
Lynn W. Deffenbaugh (...
ldeffenb
May 3, 2009 4:13 pm
I'll have to check mine as soon as I put it back in the car. I believe I've got two memories set on 144.390, one in normal mode and one in data mode. If I'm...
7344
Richard Braddock
ae4bp
May 3, 2009 5:06 pm
I was able to get this to work correctly by first erasing the memory channel that the digi is programmed to and reprogamming it with the data mode enabled....
7345
Patrick
ve3wst
May 5, 2009 1:58 am
Scott, Is there any way of doing a receive level display in the diagnostic part of the config program? when trying to tune up radios and trackers its hard to...
7346
zl1vfo
May 5, 2009 11:28 am
... On a related note, it would also be nice to have it show the individual levels of the 1200 and 2200Hz tones - to get an idea of the amount of twist in the...
7347
Scott Miller
n1vg
May 5, 2009 3:31 pm
Can't do any level monitoring on the T2 because it doesn't have access to the raw audio. The OT1+ does and I could show the raw audio level. For showing the...
7348
Rob
rhenry81
May 5, 2009 10:01 pm
I can manually short the PTT to Ground and all is well but when running the diagnostic program and keying the PTT I get oscillations on the PTT relay in the...
7349
Scott Miller
n1vg
May 5, 2009 10:20 pm
How much current does it need? The 2N7002 can handle a fair amount for a little MOSFET. All of the ferrites on the board are there for RFI suppression. Will...
7350
naklugman
May 6, 2009 12:25 am
Hi, Sorry about the basic question. I have a icom ic-3200a transceiver I was hoping to use with my tracker2. I only need it to receive packet data from the...
7351
Scott Miller
n1vg
May 6, 2009 12:27 am
It's not a serial cable you need, but yes, all you need is ground and the speaker output. Scott...
7352
Rob
rhenry81
May 6, 2009 4:58 pm
Scott, Thanks for replying so quickly... I tried the 100ohm resistor in-line and did not help. I also Measured the current and its only like 10ma. I am...
7353
Scott Miller
n1vg
May 6, 2009 5:51 pm
... In diagnostic mode, it just tells the tracker to turn PTT on, and the tracker turns on that pin. There's no other logic to it. I'd check for possible RFI...
7354
Rob
rhenry81
May 6, 2009 6:36 pm
... Hmmm... RFI... maybe I should put the covers back on the radio. I am using a dummy load. And I also cranked the power down to almost minimum. But still...
7355
Bruce W. Martin
kq4tv
May 6, 2009 7:20 pm
Here is some additional info to posibly use as an argument to get Garmin to fix the duplicate waypoint problem in the Nuvi and StreetPilot GPS units. I...
7356
Rob
rhenry81
May 6, 2009 8:46 pm
... Not having any luck... I sealed up the radio.. added ferrite cores to cable. The easiest work around my be a small 12v relay. But not having a parts store...
7357
Wes Freeman
cycliste3
May 6, 2009 9:48 pm
Hi Rob, How about trying this: Disconnect the radio and then measure the processor pin that drives the gate of the 2N7000. It should either be a steady 0V or...
7358
Rob
rhenry81
May 6, 2009 10:53 pm
Hey you guys know that pin 9 on the serial connector looks like a six upside down..... LOL.... Sorry had Ground running to pin 9 instead of pin 6... All...
7359
naklugman
May 6, 2009 10:54 pm
can i use this cable? https://www.argentdata.com/catalog/product_info.php?cPath=21&products_id=117&osCsid=h0o3bas0om9kkk8rh7ka6aqfn3 Thanks, Noah...
7360
Scott Miller
n1vg
May 6, 2009 11:02 pm
Nope, it's missing pin 6. I had those made for serial applications only. It's usually easier to start with the audio cable and solder on a DB9. Scott...
7361
Tanner Lovelace
kb4tye
May 7, 2009 6:34 pm
This question is off-topic for the list, but if I can get it resolved it will allow me to get a T2-135 so hopefully it's ok. I recently bought a DR-135...
