Hi all, strange behavior of OT2m if you activate TELEMETRY SEND EVERY 2nd packet and STATUS TEXT SEND EVERY 3rd packet then the ot2 will never send a status...
Kevin NB7O wrote... ... That explains that - hi! ... There may not be an issue. I could just be that there are no nearby digipeaters. ... Possibly, but when...
Please help! I cannot find a wiring diagram to connect the RG-45 mic jack on my Motorola MaxTrac radio to the DB9 on the OT2m. I know that I will need to draw...
Hi: Does your Maxtrac have the 5-pin or the 12-pin accessory connector at the back? I have the schematic for using the 12-pin, and the connectors are...
Hi: I forgot to attach the schematic to my first email...here it is. Best Wishes, Bernie VE3OTR ... The following section of this message contains a file...
here is a link to info on the maxtrac interfacing that might help. http://www.repeater-builder.com/maxtrac/max-rptr-int.html ... From: "akamr.fixit"...
I have a Nuvi 350 and purchased the 010-10813-00 Mini-B Data Cable to hook it up to a DR-135 w/T2-135 installed. Works great. Purchased a GTRANS to hook up the...
Hello i have the tracker 2 set up as a digi i have noticed a some people running wide 2-1 my digi is 2-2 what whould happen if i have wide2-1,wide2-2? ...
Mike WD5MHZ wrote... ... Are you talking about your own outgoing path? Something like a KPC3+ is capable of using multiple paths... e.g. one beacon per hour...
I am also looking for an answer to this question. The default on power up in NOT in data mode. I am also not able to save this in the memory location. It would...
hmmm. i just powered off my DR-135T mkIII and then powered it back up and it came back on in data mode. i then disconnected it from the camper's battery and...
I'll have to check mine as soon as I put it back in the car. I believe I've got two memories set on 144.390, one in normal mode and one in data mode. If I'm...
I was able to get this to work correctly by first erasing the memory channel that the digi is programmed to and reprogamming it with the data mode enabled....
Scott, Is there any way of doing a receive level display in the diagnostic part of the config program? when trying to tune up radios and trackers its hard to...
... On a related note, it would also be nice to have it show the individual levels of the 1200 and 2200Hz tones - to get an idea of the amount of twist in the...
Can't do any level monitoring on the T2 because it doesn't have access to the raw audio. The OT1+ does and I could show the raw audio level. For showing the...
I can manually short the PTT to Ground and all is well but when running the diagnostic program and keying the PTT I get oscillations on the PTT relay in the...
How much current does it need? The 2N7002 can handle a fair amount for a little MOSFET. All of the ferrites on the board are there for RFI suppression. Will...
Hi, Sorry about the basic question. I have a icom ic-3200a transceiver I was hoping to use with my tracker2. I only need it to receive packet data from the...
Scott, Thanks for replying so quickly... I tried the 100ohm resistor in-line and did not help. I also Measured the current and its only like 10ma. I am...
... In diagnostic mode, it just tells the tracker to turn PTT on, and the tracker turns on that pin. There's no other logic to it. I'd check for possible RFI...
... Hmmm... RFI... maybe I should put the covers back on the radio. I am using a dummy load. And I also cranked the power down to almost minimum. But still...
Here is some additional info to posibly use as an argument to get Garmin to fix the duplicate waypoint problem in the Nuvi and StreetPilot GPS units. I...
... Not having any luck... I sealed up the radio.. added ferrite cores to cable. The easiest work around my be a small 12v relay. But not having a parts store...
Hi Rob, How about trying this: Disconnect the radio and then measure the processor pin that drives the gate of the 2N7000. It should either be a steady 0V or...
Hey you guys know that pin 9 on the serial connector looks like a six upside down..... LOL.... Sorry had Ground running to pin 9 instead of pin 6... All...
Nope, it's missing pin 6. I had those made for serial applications only. It's usually easier to start with the audio cable and solder on a DB9. Scott...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
