Sounds like a defective board like mine. Reflowing solder joints around the 2211 chip solved the problem (be careful, the parts are so tiny). 73 de Paulus...
4416
Bruce W. Martin
kq4tv
Jul 26, 2008 1:22 am
I want to use my T2 with javAPRSsrvr and my U2K WX station. The T2 with javAPRSsrvr is working fine. I tried adding a UII WX station but it kept the T2 from...
4417
Scott Brock
kb9szw
Jul 26, 2008 2:27 am
Thanks Keith and Paulus. Keith, you were right about the profile switching. I guess with the default settings the profile is banging back and forth between 1...
4418
Patrick
ve3wst
Jul 26, 2008 2:44 am
Hey Scott, Any update on the enclosure status? p...
4419
Scott Miller
n1vg
Jul 26, 2008 4:21 am
Yes, they came in today. The bad news is that the rear panels had the radio connector offset by about 1/16", so they won't fit. I'm not sure how they managed...
4420
Scott Miller
n1vg
Jul 26, 2008 4:33 am
... It's made a big difference on some boards. I think it's more a matter of excess flux than solder joints. I'm checking all of them before they ship now....
4421
Ron Malinowski, Jr.
ronald74
Jul 26, 2008 8:51 pm
Okay am experiencing a user problem, Im sure, but your help is appreciated, I know my Garmin 60C worked with the OT2m showing calls and symbols. I recently...
4422
Ron Malinowski, Jr.
ronald74
Jul 26, 2008 9:27 pm
One additional piece as I rechecked my connections under the radio where the T2-135 is located and realized there was two LED which I remember the OT2m had a...
4423
ricer3dad
Jul 27, 2008 12:46 am
I've used the OT2m on my motorcycle (and have loved it). Just wired up a DS18S20 to the RJ11 connector and enabled the 1wirewx. Is there a way to enable the...
4424
Scott Miller
n1vg
Jul 27, 2008 1:09 am
The weather symbol is what tells receiving stations it's a weather packet. Won't decode properly otherwise. Yet another interesting 'feature' of the APRS...
4425
Jason KG4WSV
joeuser66
Jul 27, 2008 2:19 am
addressing your original problem of the on board temp sensor, those are pretty simple, solid, and reliable as a general rule, although I have found the...
4426
ricer3dad
Jul 27, 2008 3:31 am
Scott, thanks for the reply on the APRS spec. Guess I'll have to live with it then... Jason, the on-board temp reads 60 F, whether it's out in the hot Texas ...
4427
Keith VE7GDH
ve7gdh
Jul 27, 2008 9:52 am
Ron N9QGS wrote... ... Keep in mind that the front port on the DR135T is one way... data IN to the T2-135T only. Data IN on the tip, ~5V+ out on the ring and...
4428
Keith VE7GDH
ve7gdh
Jul 27, 2008 11:24 am
Scott KB9SZW wrote... ... If you remove all of the checkmarks in the profile switching, that will prevent from switching. ... Keep us posted. My T2-135T seems...
4429
P. Suryono Adisoemarta
n5snn_1
Jul 27, 2008 11:42 am
... Maybe you inserted backwards? I had that situation before when I put the sensor remote (not on the board, but over a short wire so the sensor would be...
4430
Jason KG4WSV
joeuser66
Jul 27, 2008 12:07 pm
If you do figure the problem out, it should be possible to remote that sensor as well - just extend the 3 wires from the PCB to wherever you want the sensor. ...
4431
Mark Miller
markm76017
Jul 27, 2008 1:26 pm
... If you have jumper on or jumper off set for profile switching, every time you connect to the serial port the profile will switch. 73, Mark N5RFX...
4432
David Gibson
ka5j
Jul 27, 2008 4:02 pm
The on board temperature sensor in my OT2M used to work but now I've noticed it's stuck between 64F and 65F. I tried updating my firmware to 54479 which hasn't...
4433
Scott Miller
n1vg
Jul 27, 2008 6:39 pm
I'm going to check it out today. I had one that looked stuck, too. Scott...
4434
Jim Tolbert
riverridge_wi
Jul 27, 2008 9:00 pm
Hi, all........... I have an Alinco DR-135 with a T2-135 installed. I would like to run the Alinco DR-135 programming utility from CBT to program the various ...
4435
n0uyx
Jul 28, 2008 12:25 am
OK TNX Not sure what is going on then sometimes it works sometimes it doesn't. Strange Randall ... write ... to ... used ... that is ... that ... Now ... ...
4436
Scott Miller
n1vg
Jul 28, 2008 4:50 am
I thought the programming was always done through the front panel. Does the Alinco TNC pass commands through to the radio? I can't see how it could when it's...
4437
Dan Dicke Electric
ke6nyt
Jul 28, 2008 5:19 am
The CBT program works through the front and you need to have the data off. This disengages the T2-135 anyway. Mine works fine. Make sure you are in voice...
4438
Jim Tolbert
riverridge_wi
Jul 28, 2008 11:14 am
Ah, Excellent! Thanks for writing, Dan. Maybe it is a speed issue. What settings do you use on the COM port? Thanks again............ jt ... -- Jim Tolbert ...
4439
Dan Dicke Electric
ke6nyt
Jul 28, 2008 2:24 pm
There isn't a baud rate setting. The CBT software only allows you to set the comm. port. The software knowing that you are only using the alnico radios and...
4440
usna71
Jul 28, 2008 8:44 pm
Hello: I am beating my head against a brick wall trying to get UI-View to see position packets being sent by another tracker. UI-View is connected to a DR-135...
4441
Bob Burns W9RXR
w9rxr
Jul 28, 2008 9:24 pm
... I use a T2-135 with UI-View in KISS mode and have occasionally beat my head against a wall, too. Your commands look OK. You might want to check the baud...
4442
Clay Jackson
clay_jackson
Jul 28, 2008 11:54 pm
I have one of the traffic radios, and it wants to plug into the side port, not the dock port. It also requires external power (provided through the dock...
4443
Patrick
ve3wst
Jul 29, 2008 1:27 am
That likely means that it interfaces with the gps using FMI or something along that lines... and therefore most likely you would have the selection of traffic...
4444
Bruce W. Martin
kq4tv
Jul 29, 2008 1:34 am
Let's try this again: I want to use my T2 with javAPRSsrvr and my U2K WX station. The T2 with javAPRSsrvr is working fine. I tried adding a UII WX station but ...
