Hi All: I just purchased a used DR-135T and T2-135. One thing I noticed after setting it up was that there were a LOT of FCS errors, even on packets that...
... As you know, Scott, the HamHUD group has been interested in this for a little while now. My request would be to leave the RS232 transceiver off, but I can...
... This is exactly what I was talking about when we talked it over at DCC. I see it as a T2 veriant of the current SMT OT1+. Jason KE4NYV RPC Electronics ...
Scott, You can get small wrenches from automotive tool sources in sets called "ignition wrenches." Or at least I suppose you still can, although I think most...
Hi Group, Since there continues to be interest in this I'll fill the group in on what I found and what I hooked Scott up. Wiha makes a 3/16" nut driver that is...
Hello to the Group, I have a bit of a mystery with my new Tracker2. Using my VX-7R, the Tracker does not cause the HT to transmit (even though the Tx LED comes...
By TX LED, do you mean the one on the tracker or the one on the radio? Here's what I found for the VX-7R pinout: http://www.kc8unj.com/pinout.jpg Scott...
I've never heard about a problem with the VX-7R. I know it works fine with the VX-150. I swiped my son's and use it for testing. I suppose I can give it...
Hi Tom, According to the VX-7R manual under the "Interface to Packet TNCs" you can find a schematic to get started with. I built a cable some time ago for a ...
Howdy Tom, The VX-6R manual shows the packet interface should have a 2k resistor in series with PTT, and a 10uF cap in series with the MIC. I have built a...
If the internal resistor value doesn't work, you can always pull the HT jumper and use an external resistor. I don't think you'll need the 10uF cap. Scott...
All is working fine now. I just had not opened the case since getting the unit. I did so and placed the jumper across the "HT" pins and that did it. Thanks to...
Try the RX EQ jumper and see if it helps. Normally it's better to leave it off with an HT, but try it and see. Also, you might try running open squelch -...
Connect by using hyperterm to the OT2m, then type: amode kiss then under agwpe, set to the correct comm port, and select the mode as KISS. That's it. 73 de...
Should otwincfg bugs be reported here or somewhere else? I looked at the OpenTracker sourceforge repository but it doesn't seem active and only has two...
Update - OK now - I have grown to expect the unexplainable from computers but this is too strange ...... To answer Scott's questions: All the LEDs come on at...
I would like to take the next step with the Tracker2 and purchase a basic Wx station. All I want is Temp, Wind speed/direction. 1st - Am I correct in thinking...
I've been using the LaCrosse 2317 with a T2 board for a couple of months (since April). Standard firmware, just need to enable with "amode ws2300" command ... ...
I've been trying to use a Peet Ultimeter 2000 for the past year (with no external humidity sensor attached). That configuration does not work right. It gets...
I posted a fix for the OT1+ recently, but I haven't been able to reproduce the problem on the T2. You should make sure AUTOBAUD is off, if you haven't...
... Right. ... There have been some Ultimeter problems reported, but they're probably the best stations. I use the AAG 1-wire station and LaCrosse WS-2310 ...
Updates all around tonight. Nothing major, but probably worth an upgrade next time it's convenient. For both the OT1+ and Tracker2, the processor should now...
I've got a T2 beta (B, I think, could be A) that I can't talk to with the config program. I have the latest config program (11-08-2007), have tried to disable ...
Yeah, I'm guessing that you've got such an early version of the bootloader that it doesn't check that bit, so only the regular firmware is uninverted. Hmm......
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
