It should fix a few issues relating to outgoing packets. I won't promise that it's *all* of them. Right this second the code isn't stable and ready for...
15187
Scott Miller
n1vg
Jan 31, 2013 10:23 pm
It's a 4-conductor 3.5mm jack. Right now my biggest problem with the design is that I either need to eliminate the HT and HI jumpers or make it easy to open...
15188
Scott Miller
n1vg
Jan 31, 2013 10:38 pm
How old is this unit? And are you running the latest otwincfg? The significance of 0xde00 is that it's the start of the USB bootloader. The OTUSB can't update...
15189
Scott Miller
n1vg
Jan 31, 2013 11:27 pm
I finally got a chance to try replicating that packet, and it doesn't seem to cause any harm. It doesn't decode to the proper position because of the mangled...
15190
Matthew Cook
psionicoz
Jan 31, 2013 11:28 pm
No spare I/O ? Couple of well placed MOSFET's and make it a software option. 73's Matthew VK5ZM ... -- Matthew VK5ZM 0487 653 245...
15191
Scott Miller
n1vg
Jan 31, 2013 11:30 pm
That's the idea right now, but it's a pretty tight squeeze already, and I'm reluctant to add one more firmware variation. Scott...
15192
n9tkf
Feb 3, 2013 11:42 pm
I have an OT USB that I am using for telemetry. It seems that the telemetry inputs on CN-4 are a bit skewed. CN-4 pin 5 is connected directly to my battery....
15193
Joe Della Barba
joe@...
Feb 4, 2013 1:13 pm
My OT-3M has been reporting 0.3 volts low for about a year now. I could change the telemetry by sending a message if I can remember the format, but that won't...
15194
n9tkf
Feb 4, 2013 6:06 pm
I did look at your telemetry values before I posted. Your telemetry values show:::Battery: 12.900 Volts (TLM: 129 EQN: 0,0.1,0). The TLM: 129 corelates to 12.9...
15195
Thomas
aprsyos
Feb 4, 2013 7:18 pm
Scott I am running an OT3m with firmware 56294 When sending a message with the SEND command the OT fire up the Power Control PS with 12 volt. But when the...
15196
James Ewen
ve6srv
Feb 4, 2013 7:44 pm
... How are you sending these commands? Direct from the keyboard, via a script, or some other means? Is the "fire up the Power Control PS" a command you are...
15197
Scott Miller
n1vg
Feb 4, 2013 10:39 pm
There's not presently an adjustment, but I should be able to add that in the next firmware version. Everything is referenced to an internal band gap...
15198
Thomas
aprsyos
Feb 5, 2013 10:52 pm
... I am sending the SEND command via the serial terminal. The message from the send command are transmitted but the power from OT will not turn off after...
15199
Burak
burak_demirci
Feb 5, 2013 10:52 pm
Dear All; I do not know if you talked about such a topic but I have a problem with my new otm3. The equipment: I edit the otwincfg file, if you want I can send...
15200
n9tkf
Feb 5, 2013 10:52 pm
Thanks Scott for looking into this. I do have a question though, if I put 20 volts on say CN-4 pin 3 (analog input 1), what value would be output in the...
15201
Thomas
aprsyos
Feb 5, 2013 10:52 pm
I am sending the commands from the serial console and I have the Power Control enabled in the config. I want to have the same function as for sending a beacon:...
15202
James Ewen
ve6srv
Feb 6, 2013 2:00 am
... Ah, got it... I mixed up the POWER and PULSE commands in the last message. I've played with PULSE XX not POWER XX. I can't recall for sure if there was...
15203
Rob
notrobbage
Feb 6, 2013 8:23 am
... I wonder if power stays on to allow reception of ack message? Have you checked to see if it eventually turns off again after a minute or two? -- Rob,...
15204
Thomas
aprsyos
Feb 6, 2013 2:40 pm
... All acks seems to be received, no turn offs, I have wait for 60 min now. But if I send out a beacon it will be turned off direct Thomas SM0YOS...
15205
JohnD
k0jdd
Feb 7, 2013 12:34 am
Latest incident occurred on Feb 2013 @ about 06:40 am Central time. Video this time. Part 1. T2 totally frozen this time and not responding to RX or console....
15206
Scott Miller
n1vg
Feb 7, 2013 2:16 am
You're right, it seems unlikely that it's something other than the bad Mic-E station. Unless maybe the LCD is getting stuck on that packet, and the lock-up is...
15207
Scott Miller
n1vg
Feb 7, 2013 2:34 am
I've just updated otwincfg to add a check for duplicate switching conditions like this. It now won't allow you to set conditions that could clearly result in...
15208
Scott Miller
n1vg
Feb 7, 2013 2:35 am
... It's not doing that on purpose. I do remember recently fixing a power control hang on the OTUSB that might have been related, and the code is shared...
15209
Scott Miller
n1vg
Feb 7, 2013 4:13 am
Yes, it should read 200. It might not get all the way to 200, depending on the exact supply voltage the MCU is getting. The limit is actually 4xVdd and on...
15210
Thomas
aprsyos
Feb 7, 2013 11:52 am
... I am running Tracker3 beta build 56294 downloaded from the web and it's still happening. Thomas...
15211
n9tkf
Feb 7, 2013 3:34 pm
I did some testing last night and found if I put 5 volts on any of the analog pins on CN4 that all of them would give me a max count of 164.By max count I mean...
15212
Scott Miller
n1vg
Feb 7, 2013 5:05 pm
Sounds like maybe there's something wrong with the voltage dividers. There's a green resistor pack on the left side of the board, and a row of resistors close...
15213
Scott Miller
n1vg
Feb 7, 2013 7:37 pm
New beta releases are up (build 56330) for all three products. Fixes include: All: Power relay now switches off after APRS message packets OTUSB: Fixed...
15214
Scott Miller
n1vg
Feb 7, 2013 7:38 pm
I just uploaded new beta firmware. Should fix your problem. Scott...
15215
Marcel S
ki6qdj
Feb 7, 2013 8:24 pm
Scott, You do some awesome work! Thank you for supporting your products so well and continuing to update their software with improvements and new features. ...
