Ok, to back up a bit, what is the current problem? It's not transmitting? I'm digging out of holiday email right now and I'm a bit behind. Scott _____ From:...
The OT2 can be used as a digipeater? I want to be able to put a digipeater on the air here but the current TNC's are cost prohibitive. Can it be used as an...
... Yes, and does a considerably smarter job of it than any other TNC out there. And you can still use it for a TNC while it's digipeating. -Jason kg4wsv...
Hi Scott, What's your rough time line for production units? Secondly I realise your probaly running out of room for more programing on the chip but what are...
Still working on getting production set up for the T2-135 units, since they're the simplest. I hesitate to provide a firm timeline right now - I still don't...
Hi all, I'm trying to use my OT2 as a digipeater and have encountered a strange problem. The OT2 (Build 54076) seems to be sending and receiving O.K., but...
The T2's digipeater functions are intended for APRS use. I've never actually tried using it for connected mode. Any idea how big the packets are that it's...
Thanks for the help, Scott, that must be the problem. The packets that the OT2 did relay were about 200 bytes. The 'Help' data was over 600 bytes. "Back in the...
Hi, I'm about to finish building the OT2 kit and have a question regaring the software. Has the micro already got the bootloader programmed? If not the...
Hi Graham, I believe Scott is shipping these with them already programmed, it may just not be the latest version, that is how mine was when I received it. I ...
It's pre-programmed with the bootloader and the regular firmware. Should be ready to run. Don't use otwincfg-dual, though - use the standard otwincfg.exe...
Thanks Scott and Stephen. I finished building the OT2 and the otwincfg.exe file worked first time. Now off to configure and try it out. Thanks. 73 Graham ......
Scott - what was the command I had to go in and manually change for the T2 to work with the Alinco? I should have wrote it down but I didn't and now I can't...
Hi Graham, I received my OT2 kit last December, and the micro was already programmed with build 54085. Just power it up and go! FWIW, otwincfg-dual.exe didn't...
I think it was BMODE AUTO. Still at Cape Canaveral, should be back on Saturday and will get back to work on it then. Scott _____ From: tracker2@yahoogroups.com...
Has anybody had any success with the multiple waypoint issue on the Garmin GPS. eg. test,test 1, test 2, test 3, test 4 etc. The GPS in question is a Garmin...
Finally I got the time to put aside to work on my Tracker2 Proto B board, and, after 5 hours (split in 2 days), it is now completed. What is the state of LED...
In summary, my proto B is not responding after I finished building it. What I've done: - using otwincfg I've been able to update the bootloader and firmware -...
The last thing you loaded was the regular firmware and not the bootloader updater, right? If not, then it's still in bootloader update mode. Can you still get...
Yes, the last thing was I load the latest regular firmware using the 'web' button. Then put the callsign, write, and quit. As soon as I quit otwincfg the green...
Try loading the firmware with the erase/reload configuration option. Maybe your config got corrupted somehow. Scott _____ From: tracker2@yahoogroups.com...
Ok, will do in a couple of hours. Meanwhile, here are 2 screen captures that I took last night of the 2 profiles. The one without JP7 would give a dead LED,...
... Thanks Scott, that did resolve the problem. Here are the steps that I took (that some of them are unnecessary): - I put a checkmark on "Erase device and...
Is there a pin with power out on the DB9 port of an Alinco DR-135T radio? That way I don't have to run another line for powering up the Tracker2 board. thanks,...
No, nothing easy. There's 5 volt power on the internal header, but it's not passed to the DB9. The T2-135 board uses it, but doesn't pass it out to the DB9...
Is the source code for the firmware available? (And if so, can it be compiled with the "Special Edition" (i.e. free) version of the HC08 CodeWarrior tool...
it appears that the device is not transmitting. When the board powers up, LED flashes red once. when using terminal-program SecureCRT (9600b with N81) I get...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
