... Not really. Read it carefully. He says that they "end their miserable lifes as "WIDE3*" and "WIDE4*"" which to me implies that they actually DID get 3...
... As above, an alias of "WIDE" and hops set to "2". An incoming "WIDE3-3" for example will go back out as a "WIDE3*" Similar with my current fill-in. I have...
... What firmware version are you running? I haven't seen that action. I'd like to play with it and see what's happening. ... Some feel that these paths over...
I recently purchased a ADS-GM1 GPS Receiver to go with a TinyTrak3 I picked up ealier in the year from Byonics. The GPS LED on the ADS-GM1 GPS receiver does...
... The current one that the GUI downloads. Just to be sure I confirmed this morning that my fill-in was definitely digipeating incoming WIDE2-2 and WIDE2-1 as...
... Can you confirm that there is 5v on pin 4 of the TT3? (ground is pin 5) I'm not familiar with the TT3 but with the Opentrackers you need to ensure that the...
Did you apply a solder jumper on J7 of the back side? Can either be Vin (BAD for 5V GPS unit), 5V (GOOD for 5V GPS units) or 0 if no solder jumper. See page 3...
I'm sorry but I'm still not sure what this means. I do have the yellow and black cable. Does that mean I'm not wiring black to pin 5, red to pin 4, and white...
PORT-A is the console so if you want BOTH the computer and GPS connected, then you must connect the computer to PORT-A (pins 2, 3, and 5) through a null modem...
Can the T2-301 be configured to output NMEA to GPSes on both serial ports but listen for incoming NMEA from only one? I want to use my GPS 18 as the source...
Split the tx lines from the output of the T2-301 to the GPS, and feed both GPS units from that feed. Don't connect the tx lines from the unwanted GPS to the rx...
I'm hoping to find a software solution that didn't involve making up custom cables. I was thinking about something in the firmware that would just ignore...
This sounds like what I am thinking about doing, but maybe a little different. In my vehicle I want the T2-301 to always transmit my position, even if the GPS...
That sounds like another problem best solved in software. Checkbox: "Transmit last good position when GPS is silent" or something like that. I wonder how...
My Nuvi 350 is generating very strong noise on specific frequencies on 2m. My previous installation used the T2 5 volts for the Nuvi and the Nuvi was mounted...
May be the easy finger pointing, but what happens if you leave the nuvi on but disconnect the external power. Usually the noise is caused by the switching...
... Certainly some more experiments would help. In my case I'm running a Tracker-2 Proto-C in my Jeep inside an ammo-can with the 2-meter radio, and a...
It won't work with the tracker that way as you need external power, but it will at least show you if the noise is nuvi related, or power supply related. For...
... I don't think there's any GCC support for HC(S)08, but you can get the Codewarrior IDE. I understand the free license now covers up to 64k, which is...
It is the regulator. I have a power switch for the gps and turned off the 12v to it. The Nuvi kept on working but the noise went away. I guess it's time for...
I have a T2 OT2M that I am using with a Yaesu FT-7800. I have been using the AGWTracker sofware coupled with the AGW Packet Engine. All had been talking to...
I have noticed this behaviour on my old pc in the garage. Restarting AGW usually fixes the issue for me. Is it more complex of an issue in your instance? Randy...
Good afternoon all, i was wondering if there is a cable for the open tracker+ to go to a Wouxon KG-UV1D? I wasn't sure if Argent had these types of cables. any...
We can make that cable:Â http://www.rpc-electronics.com/trackercables.php Jason Rausch - KE4NYV RPC Electronics, LLC www.rpc-electronics.com ... From: AllanM...
Jason, I would also be interested in this for interfacing to a OT1 with power option. (pin7) will check your site! Do you have pigtails available or is Scott...
