I recently supplemented my ARPS setup with a Kenwood TM D710. My T2 is currently doing digi duties on top of a building, and as such, my GTRANS cable is...
... I would guess it would be as simple as making a 3 wire DB9-2.5mm stereo cable to adapt the physical connection. A "standard"; Kenwood GPS cable should do...
Rick, Thanks. I am working with the T2-135 that goes inside the Alinco DR-135. There are no jumpers. But,this may help me come up with a connection....
Sorry about that I just practice a speed reading, and I'm not good at it didn't even notice the T2-135, good luck. Rick KD4DRA ________________________________...
Thanks, I thought that might be the case. Now... I don't suppose anyone has the pinout off the top of their heads? I did have a look around and couldn't find...
Hello, on request FRIENDCOM did send two PDF files. One mainly is describing how to use programming software QuickSet and the other one especially is...
I bought a new car and yesterday was pulling power wire, a connection to my Nuvi 350 GPS and an ignition key interlock to turn the radio on and off with the...
Pete, Even though you don't like poking around inside, see if you can trace the power in and then look for any large traces on the PCB. See if you can trace...
... You are right. Maybe it had something to do with too long file name. So i did use a new ( shorter ) name: http://www.kh-gps.de/fc-301d_qs.pdf 73 de Klaus,...
I am having intermittent problems getting a cmd prompt. I recycle the power and press enter several times, but I do not get a prompt. Sometimes it works on...
Is there a way to send a telemetry packet in isolation (in other words separate from a standard location packet)? It seems that I can only sent a telemetry...
The T2-135 wont connect if in KISS mode. 73, ZL1ARL. ... From: rogerstager To: tracker2@yahoogroups.com Sent: Thursday, February 03, 2011 7:54 PM Subject:...
Not yet, there's not. If you have a suggestion on how you'd like that to work, let me know. I'm thinking maybe a special parameter for the BEACON command... ...
What mode is port A set to? What baud rate? Try disabling flow control in your terminal program if you haven't already. Do the front panel LEDs blink every...
I think the simplest way would be to introduce a' TELEmetry' command that operates just like the `BEAcon' one. A line in the script that looks like:- Exec...
I have to agree. I've experienced the same issue resulting in perhaps 70% loss of TELEmetry packets. The beacon and telemetry packets cannot be sent...
On thinking about it I realise that there is already a TELEMETRY command for switching it on and off so it would need to be called something else, BTELEM for...
Both port A and port B are set in "Auto" mode. Baud rates on both are 4800. Flow control is disabled on PC side. My PC is connected through an iogear...
I have a T2-135 in my radio and connected to my Garmin 350, and had it apparently working for a few minutes. Now for some reason the 350 can't talk to the...
Gary WB0BZR wrote... ... The config program should be able to communicate with it. There must be some kind of a problem. ... No, there isn't a reset. The...
Hi! My friend have one Open tracker v1.1 + that don't have packet modulation on TX.Anyone can help what part to look?Cable for radio is ok.(checkd with other...
Hi Bob, I also have this issue with my OT2m and nuvi 350. I have them hooked up to a Yaesu FT-8900R. Tracker2 Build = 54746 nuvi 350 Software = 6.20 nuvi GPS...
There's no hardware reset, but you should be able to run the config program. You'll probably need to power cycle the radio after you hit the 'connect' button,...
