Hello guys, Proper rpms for a Top80 are 9600 + or - 300, that is static, on the ground. Anything over 9900 is under your own risk, as far as I understand. The...
I don't think this is the problem. I would start with the "LFH", the little f**king hole, and make sure it is clear, the check again fuel lines, and finally,...
Dave, mine did the exact things you describe after I rebuilt the carb. You must bend your metering lever upward slightly (manual says 0.5-0.7MM above carb...
hi guys !!! I bought a top 80 motor almost 6 months back, now I need couple of parts. If somebody can suggest a trustworthy dealer it would be great. 1. I...
Hi Dave, If you just make the setting on the fuel mixture screw a bit richer you can accelerate faster. The carburetor on your unit is great, I replaced it...
Small correction for your advertisement. The Top 80 iFlyer with composite two piece prop and composite seat, as well as 2006 lightweight muffler is 41 lbs. For...
Ary, use only Castrol TTS!!!!!!!!!!!!! It's woth the trouble to get it ary_singh <ary_singh@...> wrote: hi guys !!! I bought a top 80 motor almost 6...
Hi, Richard, Since the Castrol TTS is no longer available here, I changed tot Total Racing 2T and I am flying with it for 6 hours now without any problems. Wim...
... I tried what you said and just had a great flight. The lever was even with the base of the carb floor. I pushed it up and tried to guess at your...
hey dave...didnt know you had a top80, though your might still b e flying that fly70 and gin-bonanza combo. Email me sometime off this list and Ill describe...
Waving my own flag, but it seems to be a common problem pilots obtaining spares, so try http://www.skydragons.com/ for Top80 spares and accessories. I'm trying...
Hi, Do you have version in English? I do use Top 80 in PAP machine (PAP 1400TD). Regards, Paiboon ... From: top80@yahoogroups.com...
Paiboon
panpai@...
May 17, 2006 10:46 am
2157
Paiboon, I would prefer to read an English version of the forum but i couldn't find one (i am learning Spanish). In the mean time I am using this. Go to this...
Hi Noel, My PAP Top 80 has now done 100 trouble free hours. (apart from a loose exhaust bolt, easily fixed) I have regulary cleaned out dust from clutch bell...
Yes need membrane!!!!!!! ... Von: top80@yahoogroups.com [mailto:top80@yahoogroups.com] Im Auftrag von ary_singh Gesendet: Mittwoch, 17. Mai 2006 16:52 An:...
It sounds to me as though you are maybe running the new type reduction (3.9 to 1 which went on sale in 2005 and should run a 125x53 prop) on the old reduction...
The forum dialogue will appear in English if you select english as your language during the registration process, but in anycase the English part of the forum...
It sounds to me as though you are maybe running the new type reduction (3.9 to 1 which went on sale in 2005 and should run a 125x53 prop) on the old reduction...
I have a PAP1400 TOP80 machine with a Walbro Carb. I seem to be getting un-burnt oil/fuel on the crank case near the carb. Its running fine though. Some one...
hey! check this out.. http://www.lookherethelowest.info/jexv ..basically it's saved me a ton, you're placed up for auction and financers outbid each other...
thomasina-kirby588@...
May 18, 2006 10:55 am
2166
Hi Ary, Thank you for your suggestion. That will certainly help. I guess if I have questions I can write in English and have it translated into Spanish. By...
Paiboon
panpai@...
May 19, 2006 2:24 am
2167
Hi, I also have PAP 1400 Top80 with Walbro Carb. Mine engine which has about 20 hours of engine time also has some un-burnt oil/fuel near the crank case and...
Paiboon
panpai@...
May 19, 2006 2:37 am
2168
Thanks for the tip. ... From: top80@yahoogroups.com [mailto:top80@yahoogroups.com] On Behalf Of glanfa Sent: Thursday, May 18, 2006 4:40 PM To:...
Paiboon
panpai@...
May 19, 2006 2:45 am
2169
Hi Glanfa, This is very useful information and it is very much appreciated. My Top 80 seems to have the old reduction gear (3.6) as it was manufactured in ...
Paiboon
panpai@...
May 19, 2006 4:52 am
2170
My two cents Most top 80s drip a bit at that juncture, but the cause is different depending on the model On the really older models the case was molded...
Hunt is more widely used for describing the action of searching for game animals and shooting them but the word applies to different uses, all of which give...
