I know this is an old topic, but something I just found out about the ct-44 adapter: to receive correctly, you should use a stereo cable, not a mono one, for...
When plugging up a recently purchashed TNC-X in a vista PC should it come up and indicate it is a TNC-X? The one I have just comes up as USB serial port. Is...
It usually comes up with a TNC-X sign on and then a serial port sign on. Are you sure you didn't just miss the first one? Even if you did, it would simply...
Just joined the group and reveiwing messages, so I am aware this topic is very old, but I am using APRS4R on a WL500 and it is working a treat with my TNC-X....
The radio I'm waiting on to use the tnc-x on has un-squelched discriminator audio easily available.. Is it possible to use the tnc-x this way, or does the...
I believe it will work. I've used discriminator audio on other TNC's, but I've not tried it with TNC-X. I'm virtually certain you can't damage anything by...
There is no problem, the DCD does not need SQL to operate, i.e. on my radio (IC-228) i receive audio from the front panel 8-pin mic socket pin-# 8 (CAUTION-!!!...
Dont know if it helps but i run a few tnx-x's here and have always left squelch all the way open.. this works well because the tnc-x then decodes packets that...
OK, I've got this TNC-X sitting here -- I bought it last June and haven't put it on the air yet. Now I think I'm ready -- in the truck I drive, I use a HamHUD...
... The only real adjustments outside of the baud rate which you mentioned are audio levels. The TNC-X docs outline a simple way to get them to very acceptable...
Hi all, I'm new to this group and to packet radio. I would like to operate packet mobile on the HF bands. I notice that some of the commercial TNCs are...
G'day Roderick: I'm not sure what the regulations are in Australia, but in the US, 1200 baud packet is legal on a portion of the 10 meter band, but not below...
Hello everyone! I have been reading through posts on this forum for the past few hours, and the one that had the most promise to solve my issue was posted by...
Justin: Your VID should be 0403 and your PID should be 6001. The directions you found in the other posting were for an earlier USB module, not the one that ...
John, Good morning! Thank you for your quick response. I assume you meant use USBView to verify my VID and PID. I did this and verified my VID is 0x0403 but...
Justin: Pardon my confusion. I shipped a kit out last week to a company that also had "Intelligent" as the first word in the company name and I assumed that ...
Nick, I downloaded the manual today, and only found the suggested lists for the SSIDs and the Station List Characters. I need the list to change the displayed...
I have found this document to be vy usefull and it should contain the info you are seeking.... ftp://ftp.tapr.org/aprssig/aprsspec/spec/aprs101/APRS101.pdf 73...
Ken: Sorry to be delayed in getting back to you. I contacted the fellow who designed and sells uSmartDigi to get an answer to your question. It took a few...
Thanks John for the reply. A friend of mine bought this TNC-X already built with the SmartDigi board. I had worked a few days looking for an answer with no...
When running Txtest program, can anyone tell me what the typical values are for "Transmit Persist" and "Transmit Slottime"? Just what should I be looking for...
I would recommend you leave those at the default values. I only actually had one user who requested the ability to adjust these and I built this feature in...
John other than the two potentiometers, are there any other adjustments? Stored values or similar? Most other TNC's I have seen seem to be able to adjust many...
Graeme: There are no other adjustments. Most conventional TNCs do have a lot of parameters that can be set, but those are pretty much all ignored when the TNC...
Hi! I have just ordered my first TNC-X. Bur i wonder, does the kit include jack connectors to attach to the radio? (The jacks in the enclosure) 73 de LA8IMA...
It includes the females, as of just a couple months ago, but not males. My kit didn't work because I ignored polarity when connecting the jacks. The polarity...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
