I agree, I've now filed the mails because I found the discussion interesting. While they could now go private, I love reading such discussions -- thanks for...
If anyone's looking for an assembled TNC (with case, no USB), I have one that I just received and built last month. It works just fine, but I've decided that...
Okay, I'm kinda new at this. How do we program the x-tracker? I have looked for docs and there does not seem to be any. It will probably be a simple...
Mark, Install the x-track in the tnc-x. Hook your pc to the serial port for the TNC-X (not the gps port). Use hyperterminal and press ctrl-c soon after you...
I have a tnc-x with xtracker installed. Using a argent ADS-GM1 Gps. I don't show any packets with gps data on aprs.fi. Below is a sample of the data i am...
Mark, The x-track uses mic-e formatted aprs reports. These are designed to be short, and aren't human readable. Even the destination "callsign" contains part...
Could someone reference a link to the information on Mic-E messages? The operation manual does a poor job of this and assumes more than I know about this...
Does the tnc-x have some sort of watchdog that can cause a restart from time to time? I ask because four times in the last 72 hours I have found our recent...
I have tried everything on the configuration trying to find out what could be causing this on aprs.fi, with no success. Findu shows my position, aprs.fi does...
It appears that the invalid data only occurs while moving. I have check everything for loose connections that I can think of. Anyone have any suggestions as...
... Two stateside APRS data/map servers parse your packets and one European one does not. I'd suspect a character set encoding/decoding issue. I've not dug...
... Our tnc-x intermittent communication problem may be resolved, and I want to remove any lingering concern about the tnc-x per se. We had the tnc-x at a...
... Looking at http://www.drele.com/catalog_pdfs/Yaesu/FT-60R_M.pdf I assume you are using the CT-44 accessory as per page 11? This should be what you need to...
I've seen that. That is a really really bad diagram. That diagram is not clear as to what goes to shield/ring/tip for with plug. I've seen John hook up...
I've seen that. That is a really really bad diagram. That diagram is not clear as to what goes to shield/ring/tip for with plug. I've seen John hook up...
What do I need to do to my tnc-x if I need to setup a bbs for users to connect to? Do I need one of the daughter boards? Which software packages do you use?...
"mpechner" (callsign?) wrote... ... You would need a BBS program that could talk to a TNC in KISS mode. ... No. ... As mentioned above, a BBS program that can...
I have a TNC-X that I purchased about three years ago, and have only been using it with the Digipeater board and using the serial port. At the time I purchased...
Vince (callsign?) wrote... ... I ran into the same thing with first TNC-X with USB module. When I got around to building it, the instructions on John's website...
It is likely that the drivers that you need can be found here: http://www.tnc-x.com/USB3.htm However, since you already tried the Linx site drivers, it is...
... John, I have run across the same problem also with new drivers not be able to recognize the older module. Also, the older drivers causes "Blue Screen Of...
... John, Using the usbview.exe program reading my module VID=0X0403, PID=0XEBE0. With this information I modified the FTDIBUS.INF and FTDIPORT.INF files....
John, Thanks for you suggestion on checking the TNC-X USB with USB View, it did not show up on the screen, which made me check to see what could be the...
... Vince, Yes that is the way to go with the modifications. I accidently posted the message under the wrong subject instead of the current one. You can cut &...
Thought it best to repost my modifications under the correct "Subject: Problem with USB driver". Below are the modifications made to the FTDIBUS.INF &...