I was wondering how well the X-Digi board works for WinLink? I am looking into using them for expanding into other counties. I have been playing with a TNC-X...
Does anyone know what type of coaxial power connector the TNC-X uses? I've tried a few that I have around the shop and none fit. Thanks, Paul KE6DAX...
Paul KE6DAX wrote... ... I didn't try to check the TNC-X info, but the KPC-3 manual indicates that it uses a 2.1 mm connector. It seems to fit the TNC-X OK. 73...
... fit. ... that it ... I tried the power plug I have on my KPC-3 and it does not fit. It seems the center post on the TNC-X is a larger diameter. Paul...
Paul KE6DAX wrote... ... Hmmm... the cable I use to power either a KPC-3 or the TNC-X (when it isn't configured to be powered by the USB port) fits them both...
... There are 3 common different sizes of DC power plugs that I know of, 1.3mm, 2.1mm, and 2.5mm. Sounds like you're trying to plug a 2.1mm plug into a 2.5mm...
I am building a TNC-X right now and it is a 2.5mm plug. Kenneth Cook, W8DZN President, Bucyrus Amateur Radio Club Assistant Emergency Coordinator Crawford Co.,...
I'll stop by Radio Shack tomorrow to see what they have in stock. I didn't see a part number on the jack when I soldered it on the board. Thanks Paul KE6DAX ...
I picked up a power connector from Radio Shack, Size N. It fits just fine. Size 'N' is actually 5.5mm O.D x 2.5mm I.D. Thanks, Paul KE6DAX ... board. ... ...
I was recently presented a question concerning the TT3+ and the USB GPS receivers now available from Microsoft. Any thoughts on this working with the TNC-x?...
G'Day, I'm new to the TNC world and am a bit overwhelmed by the different options of software available and I don't know what I really need. What I want to do...
So I haven't had any replys to my question but I've managed to create a solutions to them and in the process create something that others may find useful when...
Bernard, this is very interesting. Thanks for passing on the information - it's clear that I need to learn something about UDEV :-(. I have been using a...
I have just built a Tnc-x and am try to connect to a local bbs in kiss mode. I find that I have recieve audio and am decoding packets just fine using WinPac,...
The first thing to check is whether R12 is turned all the way down so that no audio is getting out of it. Try setting it about in the middle of it's range....
I think that I have really trashed this. No audio on pin 7 and no continuity between pins 11 and 9. Solder joints look ok to me, but then I am not sure that...
Have had mine for about 2 wks now and love it never seen anything that works as good as this does just the mod is a bit high from nothing to loud needs a...
John, If you have no audio on Pin #7 of the modem chip, you may have a bad xtal. Pin #7 will always have a tone on it even when you are not transmitting. The...
Thanks. I sent it back and John Hansen has tested it and it works fine for him. Very good. At least I put it together correctly. I think the problem is in...
I have built the tnc-x and had John Hansen check it out since I was no getting any transmit audio. I have looked over my cable several times and rebuilt at...
Hi John A flashing Yellow LED means the receiver sent a signal to the TNC-x and it saw SOMETHING. But that doesn't mean the TNC-x was able to decode anything....
use agw packet engine with winpack , so u would use the agw host its the best thing to use barry ... From: John Mathieson To: tnc-x@yahoogroups.com Sent:...
I have a TNC-x running as an APRS Digipeater, at our club Voice repeater site. Has anyone used TNC-x with the XDigi plugin, in a mic-e configuration?...
Guys, can any of you give me some instructions or resources for using the TNC-X (USB) on my linux machine? I'm running Ubuntu 7.04, which recognizes the TNC-X...
G'Day Corby, I've also been using the TNC-X from Linux. I chose the TNC-X because of the USB interface and that it was powered from the USB port. Here are some...
I saw your udev post, but I guess I'm confused, because doesn't it already get set up as /dev/ttyUSB0? Thanks for the reply, hopefully we can get some more...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
