All, I have down-loaded and installed WinTNC, but am not having very much luck! I know I'm getting stuff in, as I get stuff using hyper-terminal. As WinTNC has...
This has probably been said before. If you want to see the schematic better or the hook-up diagram, do this. Open the file on the web site, then do a Copy....
Does anyone have a reccomendatiion for a KISS mode viewer for Windows to monitor my TNC-X with the X-DIGI on UHF. I tried WinTNC but it is too processor...
I have an IBM 600x running xp pro sp2. When I connect my tnc-x to it using the usb port on th etnc-x I get a message say the the usb device is unrecognised and...
I've had similar problems. I needed to run the remove the prior entries of FTDI chip drivers. I suggest the following: 1. Use Control Panel -> Add or Remove...
Thanks, but that didn't work either. I'll contact John Fran, N1GAU <http://weather.miele-family.com> _____ From: David Giuliani [mailto:wa6pxx@...] ...
Dave, I have all but given up with mine. Too many "things" have to play together, for it to work. It is a nice piece of hardware, but I feel that some fully...
I have an Alinco DJ-190 HT thats currently not being used, so I thought maybe I can play with it on my TNC-X. After some searching, I think this is the wiring...
My newly built TNC-X is not recognized by my PC. It did pass the power tests, before I put the IC's in place. While I'm likely the cause of this problem, I'd...
When you say "not recognized", do you mean XP doesn't even recognize that you've plugged a USB device in at all, or does it recognize that "something" is...
Stan: Your diagram is nearly correct. I notice the DJ-190 manual does not have a Packet hookup diagram in it. However, I looked at the DJ-196 manual and the...
No, there is nothing under U7. I have off and on again been working on developing a smaller USB module which would allow me to reduce the cost of the USB...
Brad.VE3BSM wrote... ... The circuit board design must have been changed. I have a couple of older TNC-Xs and there is just a single 16 pin socket for a Linx...
Thanks for the reply, Larry. I find that APRS-SCS does a fairly respectable job of monitoring without using a bunch of resources, but don't expect to tell...
I have added a page to the TNC-X website that has step by step details on setting up TNC-X with AGWPE. AGWPE allows you to run a wider range of applications...
i have done this as well. i installed the tnc-x INSIDE a GE delta sx unit, then run cable to my pc. works as a deployable/mobile paclink 16 channel unit. ...
Group, I've put together my TNC-X with USB, smoke check clean without the ICs, loaded drivers, configured to COM4 good and the TXTest program talks to it. I...
Gentlemen; As a quick followup, the fact that my notebook PC did not recognize the TNC-X when it was installed was due to soldering issues. When those issues...
I'm looking at making a purchse for the TNC-x shortly. I'm curious, though, as to how much assembly will be required if I do not pay for the wiring and...
Matt WX4MET wrote... ... I've built a couple. The instructions are pretty straight forward and it only takes an hour or two to put together. Keep in mind that...
Thanks for the quick response. I guess I'll go ahead and pay the additional fee for the service. I think I know the answer to this question but still need to...
Matt WX4MET wrote... ... Up to you. It doesn't take that long to build them and I think you learn a bit more about the circuit by studying the diagram and...
... I run GRLevel3 and I don't think that what you have in mind will work. As Keith explained, you will need to connect your GPS receiver to your computer...
The more I get into this the more complicated it becomes. It's frustrating but I'm still looking forward to getting everything running. The computer I'll be...
I have my TNX-X connected to my computer and the GPS connected to the TNC-X all the time. Depending upon the GPS, I use one with a serial connection, you may...
Matt, While I'm not 100% on the GPS connection of the TNC-X, as I stated previously, you need to have the tracker daughterboard attached to the TNC-X to have...
Matt, The TNC-X can run as a stand alone tracker, if you have the tracker board installed. Likewise, it can work as a stand alone Digipeater, with the X-Digi...
... The question then becomes does the TNC-X with the tracker board installed pass the GPS position data through to the TNC's serial port. If that's true, then...
Bob, Yes, completely agree! Xastir and I suppose other PC applications for APRS does have a setting for serial and/or KISS TNC with GPS. However, as you...
To my knowledge the tnc-x does not pass the gps info. Fran _____ From: Bob Burns K4RXR [mailto:k4rxr_@...] Sent: Monday, January 08, 2007 9:32 PM To:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
