What would be a good caulking to put around my aluminum fram window"s and were do I find the stuff?? Thanks NewB [Non-text portions of this message have been...
CHARLES RICHARD
chuckyr@...
Oct 1, 2005 12:04 pm
26550
... window"s and were do I find the stuff?? -mornin' `Chucky' There was recently a long `discussion' and many posts on the subject of caulking port lights...
... Frames to fiberglass or frames to plexi? There's no one correct answer, but a number of ways/products. For the frame to fiberglass joint a urethane like 3M...
If any one is looking for a tanzer cradle - I have one in good shape. I modified a motorboat trailer to hold my tanzer 22 so i no longer need it. The cradle is...
I've had 2 moderately painful destepping experiences, resulting in back injury (minor, thankfully). Can anyone tell me a decent method for 2 people to destep...
... Have followed this procedure at dock with boat in water nd on hard with boat on trailer: Detach shrouds but with uppers, using springs and small shackles,...
In a message dated 10/2/2005 2:45:41 AM Eastern Daylight Time, tanzer@yahoogroups.com writes: What would be a good caulking to put around my aluminum fram...
... How did that go? Any leaks? I just redid my windows and I was obsessive about the cleaning and caulking etc. Results? Far less leaking but still leaking!...
One side tight as a drum for 2 seasons, the other has a slight leak again. I'm pretty sure it's the silicone residue. Will remove when I have the boat tarped...
Excuse my ignorance but what is butyl?? And were could I find window gasket?? NewB Kent & Laura Hunter-Duvar <gh246@...> wrote: ... Frames to fiberglass...
CHARLES RICHARD
chuckyr@...
Oct 2, 2005 5:21 pm
26559
I use a wrist-rocket to put a line over a tree limb (shoot a 1oz sinker with 20-lb test monofilament, which is then used to pull 170-lb nylon cord up, ...
... Butyl is the grey sticky compound that Tanzer and many other builders used to bed ports, deck fittings etc. It never hardens, but will tend to creep and...
Hi Charles, I just went through this last month. I decided to work with the existing frames, many have gone to replace the frames with full lexan. I had a had...
Thomas, I have a pictorial on how I destepped my mast. You can see it at: <http://www.mobyware.com/mobyware/sailing/tanzer/haulout/haulout.html> I did...
In a message dated 10/2/2005 3:02:01 PM Eastern Daylight Time, tanzer@yahoogroups.com writes: Excuse my ignorance but what is butyl?? And were could I find...
In a message dated 10/2/2005 3:02:01 PM Eastern Daylight Time, tanzer@yahoogroups.com writes: Can anyone tell me a decent method for 2 people to destep a T22...
... folks who sail where they have to let masts down to go under bridges, etc. It was a triangle-shaped affair that worked similar to my gin pole, except it ...
Joe B Davis
jbdavis@...
Oct 3, 2005 3:40 am
26567
There's an interesting article in the October issue of Pacific Yachting about frameless or bonded windows and how they are installed. Northern Brewer has been...
... With the 1/4" tinted plexi and dark coloured caulk I used, you can't see the caulk through the lexan, unless you get very close and really look for it. The...
Hi to all, It's getting close to that dreaded time of year again. There has been some discussion at our marina about whether to leave the mast up for the...
If the boat is out of the water on the hard I would lower the mast. It makes a good boom for the trap. It only takes a short while to take it down and you can...
I have a two part question...... I have ALWAYS stored the mast on the boat, tied securely at the pulpit & pushpit. It has never been a problem and overhang is...
Why not just bring it to PCHM for winter? "Guzak, Michael" <Michael_guzak@...> wrote:I have a two part question...... I have ALWAYS stored the mast on...
I'm tempted...... Winter storage is now close to $1,000.00 (including blocking & mast storage - I have no cradle or trailer) ... From: tanzer@yahoogroups.com...
In a message dated 10/3/2005 8:11:04 PM Eastern Daylight Time, tanzer@yahoogroups.com writes: I'm tempted...... Winter storage is now close to $1,000.00...
In a message dated 10/3/2005 8:11:04 PM Eastern Daylight Time, tanzer@yahoogroups.com writes: Its a real pain working with the gasket, I heated it in hot water...
... I've stored at both PCHM and Bronte Outer Harbour. Given a choice, I would go with PCHM. In their favour: - haulout and launch on weekends, no need to...
Hi Tanzerites, We are trying to find a home for an '84 fin keel T22. Repairable damage to hull, sound rig. Delivery within reasonable distance from Rochester...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
