Sikaflex is commonly used by automotive glass shops. I've bought it from a couple of them locally and I'm sure you'll find the same scenario. Don T8.5 --...
Does anyone happen to have any ideas/plans for some type of alternative to the ... Lenard Yup - take the thing out and throw irt in the garbage - then, you...
23728
Joe B Davis
jbdavis@...
Apr 1, 2005 12:39 pm
http://www.wunderground.com/MAR may also be of interest. Joe [Non-text portions of this message have been removed]...
In a message dated 3/31/2005 10:16:38 PM Eastern Standard Time, ... There's no more relationship between those numbers (at least in North Carolina) than...
Jere, WML is for use by a WAP browser - pervasive device like a cell phone, etc, so i would not expect it to work well on a regular browser per se. If you have...
When I had #1205 The gelcoat cracked under the stress of the mainsheet attachment and the cockpit floor core got wet. I repaired the damage and then installed...
Hello everyone, I'm looking for some advice on how best to approach the following repair. I've had several suggestions and it seems confusing. I have on the...
The main issue here is to determine if water was able to get in contact with the fibreglass i.e. the percentage of humidity of the hull at that area. Best...
Rob, Will be interested in hearing responses. I, as so many folks with tanzers, have the infamous "crack." When I first located a tanzer and posted to the...
Hi Rick, Thanks for the response. I hope I was clear enough, the cracks are in the hull itself going back 45 degress on each side from the keel/hull joint . ...
Depending upon the problem with your goosneck, you may want to consider modifying it. When I purchased my T7.5 a few years ago, the screw mechanism that...
I'd find a good marine surveyor to take a look, then proceed. Remember the glass down there is about an inch thick and most Tanzer's are prone to gelcoat...
Well after searching for a tanzer for about 8 months(and reading all I could on this site)I have found one. One question - the recent survey showed moisture...
23739
Don Cavers
drcavers@...
Apr 1, 2005 6:47 pm
Yes Michael, I'm having a great time with the 8.5. Had a couple of 6.5+knt spinnaker runs off Bowen Island last week too. The only thing that is driving me...
I have added a lot of extra purchase to the main sheet. With a dodger on the problem is worse because the main sheet interfears with the dodger. If the ...
I'm likely one of the few Tanzer owners who likes the icebox. Most of our sailing is day sailing. Don't like the cooler under the cockpit for that(although...
I put a main-sheet bridge on the cabin top for my T8.5 using a strip of aluminum 1/4 inch by 4 inch, about 4ft long, bolted at the ends to the cabin top. I...
I had similar problem with my T22 gooseneck, the screw that adjusted the gooseneck position along the slider was stripped. Simple solution - I filled the hole...
Leonard Send me your e-mail address and Ill send you some photos of what I made this winter to replace the ice box. I haven't installed it yet so I don't know...
... The moisture meters that surveyors use are NOT really designed for use on fiberglass (they're about the only tool available unfortunately). They were ...
Appreciate the info. It was my first survey and it didn't sound good when the meter was beeping like mad. I spent some time today looking at past messages...
If any of you have replaced the bulkheads in a T22 you may know something about this. Even if you've just replaced the chainplates, or even rebedded them,...
... Blisters (osmosis) on a seasonally used boat are not common, nor are they common on Tanzer's, so on a seasonally sailed Tanzer, even rarer. And high ...
... are they ... And high ... whole ... the ... (has wheel ... core was ... under ... and it ... don't believe any problem was found on the deck but I will...
Is Eric no longer connected with supplying Tanzer parts? Has Ken Hodgson taken over the business? Steve C....
23751
toby jennings
tobyjennings@...
Apr 2, 2005 2:13 am
Hi All, I am looking to upgrade my T22 with a traveler, and have a number of questions. How long do I need the track to be for a mid cockpit on the top of the...
... Hi Ram; I replaced my chain-plates a couple of years ago and I found that the slots for the chain-plates were cut at an angle to the bulkhead and the old...
23753
Don Cavers
drcavers@...
Apr 2, 2005 2:49 am
Thanks Ted I'm trying to picture this arrangement. See if I have it right. Your main sheet is attached at the center on the boom then goes through stops and...
This is an interesting discussion as I JUST replaced my chain plates. First - I don't think the chainplates should have any curve. If there is a cruve it may...
