Hi Ken The author of the duplicator pages is Dave Burtchel /Niels PS: Could you e-mail me the pictures If you have all the original photos I can host them on...
I will send them to you today. Ken PS: I don't have all of the photos, just 3 or 4. Dave would have the originals, I'd think. Niels Jalling <niels@...>...
Ken, I think I still have all those old photos of the duplicator/spiral thingy. There were also some pictures of the lathe set on end and used as a mortising...
I do. I have just counted :-) I have an Unimat-4 and two Unimat-SL and a Taig and a SR80 and a Lorch 6mm and a Lorch 8mm and two Unimat-1 and a Proxxon MDG. ...
I currently own a couple of each as well as other Brands. The weak motor and constantly slipping "O" Ring belts on the Unimat-3 make it a challenge to cut...
Check out these websites. This one sells a 3/4 x 16 threaded adapter for the ER16 http://www.hightechsystemsllc.com/index_files/Page993.htm This on sells a 1/2...
once in a while my machine skips steps my max feed rate is set to 11ipm. im not shure what its limit is. mabe just cheap stepper motors. I would like it to run...
I recently got a Taig CR2019-ER, but the ER collet nut is strange.. the part on the bottom which rotates around has a hole off center which is making the...
Nope, that's the way it should be. Make sure you slide the groove on the collet into the the off center ring in the collet nut. It is designed that way to...
Nope. That is normal. That is what that lip on the fat end of the collets slot into, they should make a very slight "click" when you put them in. Scott- ... ...
And make sure that you insert the collet into the closer, then screw the closer onto the spindle, then insert the tool and tighten. ... -- felice@... is...
I'm having a weird thing with my DSLS-3000 whereby the belt after about 3 to 5 minutes of run time flips inside out with the V facing away from the spindle...
It's always caused by running the mill with the pulleys misaligned - even for a little while, it causes one side of the belt to stretch more than the other,...
Well. I'm grown up with the Unimats :-) If I should buy a small lathe today I would take a close look at the Sieg C0 lathe. They looks like a real bargain. ...
... The classic books by Holtzapffel and others are available widely as reprints. Nick Carter sells an indexing plate. While a tad small, the Taig could be...
Is the 200-00ER - Complete headstock with ER Spindle is still the same headstock as the lathe? I'd like to get a headstock and swap it in and out rather than...
... the Sieg ... Niels All I can say is good luck you may need it. My comments on the previous post on this subject were on the Sieg CO Unimat Clone. The...
My wife has appropriated (with cooperation) this motor to drive an Ashford spinning head (as in spinning yarn). This is an electric spinner and has avoided...
The housing is the same and it will mount on the lathe. As other have said though, none of the 3/4"-16 accessories will work. It does not come with collets,...
Got a good deal on a very little used Unimat 3 with loads of equipment. I actually got a brand new Taig a few weeks ago because it was much cheaper than the...
Got a good deal on a very little used Unimat 3 with loads of equipment. I actually got a brand new Taig a few weeks ago because it was much cheaper than the...
I have a question and don't have a Taig head, yet, but soon hope to have one and have a question about the 3/4-16 threads on the head. Are they standard right...
