Ahh! The Motor SAGA (Or Drama?). Thanks, Lewis, for this incredible list. You might take up a second occupation. "Thing Finder" - Somebody wants something...
Charlie Carlisle
carlisle@...
Mar 31, 2000 10:19 pm
29
One thing to remember with Taig is that it can take a really long time before they add anything new - it was about 3 years between when they said they were...
Felice Luftschein and...
felice@...
Mar 31, 2000 6:30 pm
28
... Gee, why did I not think of that. Cetrain to have the hole on center with the headstock that way. Thanks. Lewis...
Lewis Balentine
lebmail01@...
Mar 31, 2000 5:50 pm
27
... From: Charlie Carlisle <carlisle@...> To: <taigtools@eGroups.com> Sent: Thursday, March 30, 2000 6:30 PM Subject: [taigtools] Re: Lathe Lead Screw...
Felice Luftschein and...
felice@...
Mar 31, 2000 6:47 am
26
... From: Lewis Balentine <lebmail01@...> To: <taigtools@eGroups.com> Sent: Thursday, March 30, 2000 9:52 PM Subject: [taigtools] Re: Boring Bar...
Felice Luftschein and...
felice@...
Mar 31, 2000 6:45 am
25
... If you use this motor, it has a 5/8" shaft - so you can either use the headstock pulley, or make your own, which isn't hard....
Felice Luftschein and...
felice@...
Mar 31, 2000 6:38 am
24
Nick, I was looking at boring bar holder at: http://www.pioneer.net/~felice/boring.html What is the center height for the 3/4 Bored hole? regards, Lewis...
Lewis Balentine
lebmail01@...
Mar 31, 2000 6:26 am
23
... And I Quote: <==============================================================> From: "daisy daley" <daisydaley@...> Subject: synchronized carriage...
Lewis Balentine
lebmail01@...
Mar 31, 2000 4:29 am
22
... ... SNIP... About that "MOTOR PROBLEM": Have you tried EBAY. They have several suitable motors ... some at very low bids because the sellers listed them...
Lewis Balentine
lebmail01@...
Mar 31, 2000 4:29 am
21
I need to throw something into this conversation. First I don't have my Taig yet either - still working on the motor problem. Second, I called Taig in Dec....
Charlie Carlisle
carlisle@...
Mar 31, 2000 2:30 am
20
Roy, Being a jeweler myself, I appreciate those rings!I just ordered the Taig CNC mill for making dies for my jewelry. Do you have any pictures of you working ...
Felice Luftschein and...
felice@...
Mar 30, 2000 7:41 am
19
I looked at your rings. I am impressed ! Are you doing the inside engraving via the cnc mill ?? I am thinking you most have an extremely small right angle head...
Lewis Balentine
lebmail01@...
Mar 30, 2000 7:28 am
18
Hi, I have been using Taig lathes for years and years - currently have three of them... plus have adapted the headstocks as rotary axis for cnc mills etc... I...
Roy Goodell
goodells@...
Mar 30, 2000 6:52 am
17
The differences are, as far as I know, the headstock is a casting, and the gibs are only adjusted from the side, rather than adjusted from the side and locked...
Felice Luftschein and...
felice@...
Mar 29, 2000 6:13 pm
16
Here's a question I had been planning to ask Nick Carter, but I'll throw it out for everyone: "What is the difference between the Taig Microlathe [as ...
John F. Hornick
jfh@...
Mar 29, 2000 5:07 pm
15
There are now thirteen members after 48 hours. A good start. If you know any other Taig owners drop them an email. And thanks to everyone !!! cheers, Lewis...
Lewis Balentine
lebmail01@...
Mar 29, 2000 7:23 am
14
Hi Everyone, Interesting email list, thanks Lewis for starting the group. Hope to learn a lot from y'all. Simon...
simon sayez
simonsyz@...
Mar 29, 2000 7:09 am
13
I have added (or rather separated) a section of Taig User webpages to my site - as of now there are four, does anyone know of other user sites? ...
Felice Luftschein and...
felice@...
Mar 29, 2000 3:10 am
12
... Hi Nick, I am eagerly awaiting delivery of My Taig, I am sure I will have many questions after that....
Bill Marcy
wmarcy@...
Mar 29, 2000 12:07 am
11
Just a note to let everyone know that I'm subscribed to this group, will answer questions to the best of my ability, and now have a link from my page to the...
Nicholas Carter
felice@...
Mar 29, 2000 12:02 am
10
Several possible thoughts on lead screws and change gears. 1) Get a variable speed motor and machine off the two smallest pulleys. Place a 60 or 50 tooth gear...
James Eckman
fugu@...
Mar 28, 2000 6:52 am
9
"doug powell" <ddkpowel-@...> wrote: original article:http://www.egroups.com/group/taigtools/?start=8 ... hard ... turning ... Good point although I...
Lewis Balentine
lebmail01@...
Mar 28, 2000 4:46 am
8
I've had lathes set up both ways and each has its advantages and disadvantages. I like the speed of movement you get with the rack and pinion, but the quality...
Doug Powell
ddkpowell@...
Mar 28, 2000 3:21 am
7
... Thanks for the reply. My electronics expertise is getting better, but not to the level that I want to design circuits. I am more like to use standard ...
Lewis Balentine
lebmail01@...
Mar 28, 2000 1:07 am
6
"lewis balentine" <lebmail0-@...> wrote: original article:http://www.egroups.com/group/taigtools/?start=4 ... Haven't done it yet, if I do, I will...
James Eckman
fugu@...
Mar 27, 2000 2:07 pm
5
Hi lewis, I will add a link to your new Taig group to my Small Machines web site. Good luck. I hope this works out for you. We need a place for people with ...
Bret Nemeth
bret@...
Mar 27, 2000 11:37 am
4
I am going to post a question to try and get things started. How many Lathe owners have added a carriage feed lead screw ? I have just ordered my Taig. I had...
Lewis Balentine
lebmail01@...
Mar 27, 2000 7:42 am
3
Here is a short list of URLs that have information or Pages about Taig: TAIG Home Page: http://www.taigtools.com/ Nick Carters Taig Page:...
Lewis Balentine
lebmail01@...
Mar 27, 2000 12:09 am
2
Web URL: http://www.taigtools.com/ Phone: +1 480-895-6978 Fax: +1 480-895-9648 Email: sales@... USPS: Taig Tools International 12419 E....
Lewis Balentine
lebmail01@...
Mar 26, 2000 11:45 pm
1
Hi, For Owners and Users of Taig Lathes and/or Mills I was suprised to find that there was a groups for Grizzly/HF 7X10 Lathes, Sherline Lathes but not one for...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
