Hi Cedric Which Enigma is being installed into my Flamingo the Mark I or Mark II? And if it's the Mark I can they be exchanged? Regards Ian & Alison Buchanan ...
The cost in South Africa would be around R2000 for the upgrade. Is it worth it ? It could be but that depends highly on how your current Enigma is used. If you...
... You are quite right. Explorers screen is thankfully a little less costly. The screen is one of the major cost factors as we use special production, low...
To add to the previous post, we also have another EFIS in design stage to fit in between our singles and the Enigma. Roughly this is somewhat similar to a...
I have an Ultra in a Waiex. It is only reading one EGT. I have swapped the leads into the unit on RDACX and the problem stays the same. This problem has only...
Hi Ian, Unfortunately it was the Mark I, and its almost ready for test flying. I have asked what would the cost be to upgrade and I'm waiting to find out. I...
I believe you can eliminate questions about setup by looking at the raw readings in the probe debugging screen. You have to drill down a bit in the menus to...
Hello, 1. I am trying to set the Hobbs meter for use the minutes hour fraction units display. after setting the minutes option in the system unit setup and set...
What will be the screen resolution ? Is it going to be 640*480 like the Odyssey/Voyager or 320*240 like the Enigma MKI ? Ran ... idea. ... cut ... production ...
John, There is a minor 'bug' on the Odyssey Sim. When you go to the 'ALARM SETUP' menu,and arrow down, the third page does not show another page available....
My plane is an RV-6A with two tanks, one in each wing, 19 gallons apiece. Tank in use is selected by a selector valve. Is it possible (adding a second RDAC and...
Rainier, Not a high priority, but it would be useful if the 'closest airport' function (0) would import the long airport name, as well as the short name when...
Agree Roger ... Icao codes are useful on the ground. Mike ... From: "rdbjn3" <RMBLOOMFIELD@...> To: <stratomaster_users_group@yahoogroups.com> Sent:...
I have an Ultra EFIS with a Microair 760 transceiver mounted next to it. I am getting interference especially when the radio is tuned to 126.00. Even with the...
If you kill power to just the Ultra does the interference go away? Do you have ferrite cores on all the leads connected to the Ultra? Something like these: ...
Hi list, I've just realised I made a mistake ordering new probes to go with my nice new E3. The CHT probes I've fitted are type 'E', not type 'K'. They've very...
Same screen resolution as current Enigma. Explorer will have the 640x480 resolution. A word of warning though: The 640x480 resolution screen in this size has...
I too have not been able to get the current slider to work on the simulator. The current readout does not work on the hardware either. Bill Hyde ... From: John...
Ranier: One of the appealing features of the Trio EZ-Pilot is the ability to fly up to a mile off the chosen way point. I find this a great safety feature...
I had the exact same problem and guess what YOU NEED RFI SUPPRESSORS call Ferrite Beads. You also need to make sure that the ground of the EFIS is going...
12 - where were they fitted? Regards Joe _____ From: stratomaster_users_group@yahoogroups.com [mailto:stratomaster_users_group@yahoogroups.com] On Behalf Of...
Hi Bill, The hardware seems to work fine for current sensing, but seems to require the following: 1) Make sure the I/O extender is talking to the Odyssey. When...
... SUPPRESSORS call ... EFIS is ... of 12 ... Luck, Larry ... Wow ! 12 ferrites ? That must be a new record. I am using two. One for each Enigma in my panel....
Hi Keith, 1. Make sure you have setup the correct number of EGTs in the Device Setup Menu 2. Make sure your EGTs are connected to the RDAC starting on TC1 and ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
