Jim - When I turn it my SPII, it reverts to the previously selected transceiver. However, the amp does not. I know you have it programmed this way "as a...
Hi All, I'm pleased to announce that, effective immediately, Harbach Electronics (http://www.harbachelectronics.com/) is now handling the marketing and ...
Hi all, This is a bit off-topic but not by much. Please excuse the intrusion. I have four mobile rigs installed in my car. There icom (IC-7000, ID-1 and ID880)...
Concerning the 3.5mm phone connector, J303: What is the best way to route the 5 wires from the bottom of the connector. If down, it's too close to the...
Hi all, I finally got around to testing out the almost assembled SPII (only pods remain to be done. When I powered the unit on and program it, I see download...
Hi all, Bought the unit at Dayton this year. Went together with no issues and is working great. What a nice addition to the station. Thanks Jim, it was all...
I have lots of ICOM accessories here as I have all ICOM radios. I wonder there would be any issue with drilling a hole in the back of the sp2 to add an 8 pin...
I am brand new to the group. I have a StationPro2 and am contemplating how to hook everything up. I had a question about using external devices like a microHam...
I built a StationPro II with the intent to use it with multiple Icom rigs and amps but had the opportunity to purchase an Icom IC-7800 and SPE 1K-FA ($$$$)...
I'm temporarily out of extra pod PCBs (I still have enough to supply them with SP-I and SP-II orders), but have ordered 500 additional pod boards. They should...
A few StationPro II builders have told me they find the blinking green LED (which indicates that a selected amplifier is bypassed) to be distracting. It is...
I just programmed the Basic Stamp this evening and it was a breeze. It seems that if I ever want to re-program it, I would have to remove the back panel...
Hi Gang, I'm making plans for going to Dayton this year, and will be setting up a little indoor exhibit to sell my StationPro kits. If you're planning on ...
Sorry Dave, I can't do that. Just a moment .. I have detected that Jim Garland has a solution, but assembly is required. ;-) W9GB Sent from Comcast mobile App...
StationPro builders can now purchase extra Pod PCBs from the "Order Kits" page of the StationPro website. Extra pod PCBs are sold in lots of three for $20,...
Just to update everyone who watches here. Yes the back order stuff was fun, but have gotten past all of that. My wife WB0VAJ and myself have built all the...
Firmware version 2.2 is now available for download at www.w8zr/stationpro/. (Click on Download Files on the top banner.) There are three changes with this...
As you know, the SteppIR controller has built in a board that senses when the antenna is tuning and a relay opens the amplifier keyer line to prevent...
Hi Dave, Please substitute Mouser p/n 806-KF22X-B25P-NJ for the backordered 25 pin right-angle D-Sub connectors (p/n 636-182-025-113R531). The substitute...
I just think sometimes it just takes a little more time. Hope this is not an indication of things to come. Now there is another back ordered part. Mouser #:...
Jim has a pinout for the K3 on page 54 of the manual. I have used the same pinout for my K3 pod except I added Amp ALC and omitted FN1, FN2, and FN4 from the...
I want to order a kit but have an issue with the 5 pin connector. ( copy and paste from order ) Mouser #: 161-0505 Mfr. #: 161-0505 Manufacturer: Kobiconn ...
All, I have just completed the assembly of the SP-II Controller and the RF Relay board. I was able to detect the BS-2 and upload the firmware without a...
A week ago I upgraded my SP-I to the SP-II. For those of you who have the SP-I, I encourage you to install this upgrade. It is very straight forward. Since you...
Has anyone thought of putting the speaker audio through the headset jacks for those of us that wear headsets most of the time? Not defeat the speaker, but just...
After using the SP-1 for a few months, I have come to the conclusion that I should have built the SP-II! Are the upgrade kits for the SP-1 to SP-II going to be...
