Hi guys, I received my motor from Dennis today for my 10L its a 1hp job only drawback it will be another month until i can install it, too busy with the...
Bob, when you're ready to install it give me a shout if you need any hookup assistance. With any luck the original OEM hookup schematic is on the plate. Chris ...
Thanks Chris i will need help :) i can only screw in light bulbs and make the light bulb threads. I am finishing up milling 30 or so parts in my lathe right...
I got my info back today from Leblond and my 10Lx4 1/2' was shipped on Sept 18 1941 to GE in Ft Wayne IN. As soon as i can get the project shipped i am...
Bob, before you wrestle that beast into the belly of the beast you should clamp it to your bench and test it as per the diagram on the plate. It's an under...
Just a reminder for the 2007 NAMES North American Model Engineering Exoposition in Toledo April 21-22. Hope to see everyone that lives close there...Bob ...
Thanks Chris, Yes it will be prewired with a cord and the switch on the bench, if its one thing i can't stand is laying on my back trying to do something, well...
Does anybody have info on why SB used two different types of belt tensioning devices on their 10K lathes? Most catalog pictures I see have a knob on the front...
I think the knob left in 1955 or so from the pics and years i have seen. My 10k has the boss cast inside and its a 1974 but mine is a rear drive...Bob ... one...
Another data point ... my 10K which, according to South Bend, has an estimated manufacturing date of 10/01/81, and it has the long arm at the left end of the...
OK. Next question about my recent 10K aquisition. Just inside the nose of the spindle, there is a square pin that looks like a positioning key. It only sticks...
Thank you for the quick reply. My next question would then be, do I need a different draw bar for the 6-K collets? I've got 2 collet listings and 6K is not...
"do I ... Bob YES, you do. 6K collets were only used on the 10K lathe. They're VERY hard to find and bring a high price occasionaly on eBay. Good Luck!...
I can sort of see, but not quite why THIS high... http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=200098848073&ssPageN ame=STRK:MEWA:IT&ih=010 Bernie...
Now, this is a real piece of merchandise, made when workers were allowed to be honest journeymen and apply themselves to a proper job. Take a good look. You...
Just got home from NAMES a few minutes ago. Got to see Rose from Partsworks which had some cool SB items. Lots of good deals compared to buying off ebay. Saw ...
If some one can help me it will be greatly appreciated. I was boring a hole in a casting using a boring bar and a four jaw chuck to hold the work. The set up...
Hi On Thu, 03 May 2007 09:27:31 +0800, Danny Perry <danperry52@...> ... The boring bar IS bending. ... Use a tiffer boring bar if hole diameter allows...
I tried the items you mentioned. Thanks. This was not the problem. The boring bar applies the same pressure throughout so the hole should be even. It will take...
Did you take a skim cut to help reduce the effect of flexing in the boring bar? Chris Danny Perry <danperry52@...> wrote: If some one can help me it...
... If you're unable to use a larger diameter bar, try making several passes through the bore without increasing the depth of cut. You'll have to be patient....
Okay with the shimming on the main bushings and taking multiple passes without increasing the depth of cut seems to almost do it. I am machining cast iron and...
Hi ... Could also be "hollow" or lower areas. ... You could consider "line boring". You set up a "boring bar" in this case a shaft of a suitable diameter to ...
Hi, Could be the worst the ways are wore close to the chuck.. But check your set up.. Tool sharp with a small radius for nice finish? Tool on center line of a...
Thanks for the suggestions Danny ... From: Johnny Kleso To: southbend10k@yahoogroups.com Sent: Wednesday, May 02, 2007 9:34 PM Subject: RE: [southbend10k]...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
