... I don't think Solaris ever worked that way. Device entries for s0 - s7 are always present (plus s8 - s15 and p0 - p5 on Solaris x86), even for slices that...
... I did get this email. I have filed existing bug/RFEs for asking for support for these NICs using the 'bge' driver. They were accepted. BT Bug Id # 5059862 ...
I mentioned this offlist I believe so I wanted to post it. I installed b73 and use Broadcom's driver for my 5703S NICs. Well that didnt work (bug filed via...
... First, make sure it's /etc/inet/hosts (and that you didn't remove the link). Secondly, check the /etc/nsswitch.conf entry for "ipnodes" and "hosts". Casper...
Casper.Dik@...
Dec 1, 2004 12:29 pm
16345
... Thanks for the quick reply. yes I didnt remove the hard link. I only edited /etc/inet/hosts. I made that mistake a long time ago. # more nsswitch.conf ...
... I'd make "ipnodes" the same as "hosts". What does "getent" return for your hostnames? getent hosts `cat /etc/hostname.*` getent ipnodes `cat...
Casper.Dik@...
Dec 1, 2004 12:37 pm
16347
... When I run these commands, I see the following: # getent hosts `cat /etc/hostname.*` 10.43.82.173 sunfire.wixb.com sunfire 192.168.82.173 ns2.wixb.com...
... And that is with the names in them, right? ... That shouldn't matter once you've created the hostname.bge0 files. Do you have the exact error messages?...
Casper.Dik@...
Dec 1, 2004 12:52 pm
16349
... yes. I currently have names in hostname.bge*. ... There are no error messages. Just the machine boots up without any IPs assigned to the NICs. Like there...
... Look for any error messages relating to networking. Well, you could try: svcs -a and look for missing services. Or try: ifconfig bge0 plumb ifconfig bge0...
Casper.Dik@...
Dec 1, 2004 1:16 pm
16351
... all clean there ... i will try this idea this afternoon....thanks for the ideas! -- J.D. Bronson Aurora Health Care // Information Services // Milwaukee,...
... Which name is in /etc/hostname.bge0? sunfire.wixb.com or sunfire? Is it possible that sunfire.wixb.com is contained in /etc/hostname.bge0, and the "telnet...
... just the host (not FQDN) ... Dunno. This is weird. I will try the last suggestion later this morning. -- J.D. Bronson Aurora Health Care // Information...
Hi Adrian, That looks like an old Evesham Athlon64 Laptop which has been replaced by this model ...
Russell Aspinwall
russell.aspinwall@...
Dec 1, 2004 1:48 pm
16355
I look how setting on Solaris 9 load balancing and multipathing for four 1GB interfaces. Any issue Thanks F. Nohejl...
Frantisek Nohejl
fnohejl01@...
Dec 1, 2004 2:13 pm
16356
... It will boot by default in 64bit on Opterons only with fresh installation. With upgrade default will be 32bit (of course you can always change it after...
... Plenty of know hows and examples ( userly 2 NIC's ) at http://docs.sun.com/app/docs?q=multipathing How are you planning on setting them up ? Yours, Mark A....
Hello, How can I run SPARC-Solaris program in X86 Solaris? Because we don't have source, so we can't do any recompiler. Shell I run some emulator or other...
In message <20041201144702.93944.qmail@...>, =?gb2312?q?=B8 ... <URL:http://www.sun.drydog.com/faq/s86faq.html#9.19> (9.19) Is Solaris x86...
John D Groenveld
jdg117@...
Dec 1, 2004 3:14 pm
16362
... There's not much to add, rather one needs to remove the UltraSPARC I check from the boot code (inetboot, ufsboot) and you're almost fine (add an ...
... I'm running the X.org server (that's what the install selected) and had to cobble my own config together. Haven't tried Xsun yet. My native desktop is...
What is the magic command to read the disk label on an ATA disk in a Solx86 system. I'm trying to see the vendor info, make/model for the disks in a system? ...
... Hi, Could you tell us what Solaris program your trying to run? But just so you understand, Solaris Sparc binary can never run on x86 system and vice versa....
... Interface configuration errors will be recored in /etc/svc/volatile/network-physical:default.log, so you might want to look there to see what happened. As...
... Solx86 ... in a ... The low level command is the ATA "IDENTIFY DEVICE" command. The ata driver sends it to the ATA disk device at boot time (when the ata...
... I am seeing somewhat similar results with Masayuki Murayama's sfe driver on my laptop. sfe0 comes up with an address of 127.0.0.1 with a hostname of...
... I noticed this too. I had 127.0.0.1 assigned to bge0. -- J.D. Bronson Aurora Health Care // Information Services // Milwaukee, WI USA Office: 414.978.8282...
