As I have mentioned in my request for Software (I have now choosen to use PowerSDR-iq) I have problems reveiving anything. I got a Chinese AM station the other...
Have you took the time to look at the fivedash.com website and followed the links to obtain information on how to build them and set up the software correctly?...
Hi I need to concentrate on other projects, so I am reluctantly selling my Ensemble TRX and M Audio Delta 44 Audio card. I have just put them on eBay. Item...
A little bit more if I connect it to my pc it can be heard on my 817..infact its very loud and wipes the band out..it appears to tune ok with cfgsr.....but...
... Subject: [softrock40] Is it working or not..... ... Hughie, Many times bad sensitivity is due to bad soldering of the coil wires. Or, maybe, getting the...
Hi thanks for your interest in the Softrock ensemble I have for sale on eBay. If you win there is no problem in shipping to your location Don't pay until you...
... Subject: [softrock40] Antenna problems? ... Ulf, If the noise level drops when you remove the antenna then noise is the problem. The Softrock is not as...
I have summarized the techniques of which I am aware whereby one locates pin 1. See the summary at: http://wb5rvz.org/common/locatingPin1 ... -- Cheers, Robby...
I have just reached the point in building the RXTX where I can test the RX. I can hear plenty of good stuff but am not able to tune in the chosen sdr...
Did you copy ExtIO_Si570.dll into each of those apps directories? 73, Tim Herrick, KQ8M Charter Member North Coast Contesters kq8m@... AR-Cluster V6...
I am receiving unwanted reception of Signals that I am not tuned to. For example if I am listening to a CW signal at the lower end of the band, I am also...
... Subject: [softrock40] Unwanted signals in bandpass when Near Spur ... This is a mixer setting. You have "Line in" enabled in your soundcard playback mixer....
All Peaberry radios are now shipping with the latest firmware announced last week. With this out of the way, I've been able to turn my attention to support and...
Very neat - a 7" or 4.3" touch screen would make a nice neat package but may be underpowered for some SDR applications. 73 ... Sid. ... -- Sid Boyce ......
Hello, You can construct a nice receiving antenna out of coax and a inexpensive plastic variable that are used in cheap radios. ... From: Ulf Holt To:...
I will check the line Input to make sure it is muted also. I have attached in the photos a screen shot of the item, under IMAGES II. Thanks for the response....
Steve I am attaching a .pdf document on the construction of the Ensemble II receiver. This has everything you need. Look the document over before you begin,...
Finally fixed. I plugged the Ensemble RX into the XYL's laptop running xp and it immediately popped up with the correct message and accepted the driver. This...
... Subject: [softrock40] Re: Ensemble RX and case now for sale ... steve That's about the most common reason. But I wonder why you ignore what people say. 73...
Alan G4ZFQ: Thank you so much, after looking and looking for the correct place to disable the line in recording function, I finally found the menu and muted...
I will try this construction, but I have a few questions. 1) what dimensions are we talking about? 2) how large capacitor and do I have to pick a frequency on...
Steve wait.... Now that you've got the drivers installed you need to try the RXTX. :-) Why don't you offer your receiver to a local club member that hasn't...
I have some switch mode power supplies, including my PC. I can try to turn of everything (except my PC, of course). I have a laptop I can run on the battery,...
Steve, Perhaps one last hurdle- you're running HDSDR without needing to control the frequency with CFGSDR right? ExtIO is a driver that needs to be in the...
There are a number of DOS and Windows loop calculation applications like mloop31, loopcalc.exe, RJELOOP1, etc. available via a search engine. With the...
John Yes it did put the ExtIO file in the HDSDR folder and indeed you can control the frequency that way. The band switch arrangement is a bit fuzzy however. I...
