All seems to work OK except the only output to the system, PTT is at +5v and doesn't change. We can receive and transmit if we take manual control of the PTT...
Its puzzling, but I see post delays longer than 20 hours at least for posts from my country, eventually that makes us 'out of sync' in correspondence here. It...
www.probemaster.com sell a nifty Kelvin tweezer test-lead. I use it all the time with my AADE LC meter. Works great and is relatively inexpensive. (less than...
Still having a problem with a V6.2 RX/TX. This rig was working fine with a newly installed Windows 7 OS. I am using the FA-66 Interface and PSDR-IQ, latest...
I have just finished the Softrock Lite v6.2 and Z10000 filter for my Elecraft K2. Can you point me to a site or advice on fitting the Softrock board into the...
Using Vista 32 bit version I have a new rx-tx 6.3 kit and have completed the construction down to the mixer stage. All the dc tests look good. I installed the...
I built one of these Ramsey linear amp kits a few weeks back. It's an easy one evening project and a good quality kit. It comes with the case included. No...
Folks, I have put together a patch file that will give you back the VK6JBL automatic IQ balancing in Quisk-3.3.6. It is in the AC0OP folder under the...
Hello all, I've got a new 6.3 RXTX kit just as Tony shipped for sale. I ordered it to use with the 4.3 MoBo, but there is the SMD 6.3NG that is laid out just...
Hi! I built RXTX v.6.1 (still yet). I finished it today but it not works. I have a voltage problem with U8 (pin 1-4.88 V, pin 2 - 3.51 V instead 2.5 V) and...
Highest score* in the SKCC Weekend sprint <1W QRP class this last weekend using my solder warm Softrock 6.3 barefoot. It was built during the week and I added...
If I used a softrock with the proper input filters, and input attenuation, with multi band/freq control (sI570/usb) and Winrad, it would become a spectrum...
Hi, I am finishing a Softrock Lite II kit for use at 500KHz. It basically is the 80M kit that has been slightly modified for a 2MHz xtal and uses a different...
I've got some questions about the PAF boards. I'm planning on running my RXTX6.3 board in a sealed rf-tight case, and use it in modular fashion with external...
Folks : Pardon me posting this message to Tony, but for some reason I have not received an answer to this email directly from Tony. I know that he has to be...
Hi all, Â Also Holding down the 'Alt' key while pressing 'Prt Scr' will capture the active window. You can then paste into a document. Â Cheers and 73, Wes -...
First Softrock40 completed. Following detailed builders notes, I try to set up Rocky to try it out. Download, install and start Rocky. I don't get the screen...
GM, I'have built a v9.0 Lite + USB Xtall Receiver with Si570 and electronically Switched BFP kit and it works great with Rocky and winrad. This is really a...
From Pittsburgh to zero land, and with a slightly elevated supply- 14V-I'm getting just shy of 2 watts. The tone is pure and stable. Rocky is an OK way to...
Hi All I recently purchaced a Softrock40 lite 11 and love it. Due to my hands not working to well these days, Tony was kind enough to send me an assembled...
I am confused, but that isn't too new :-) The little addendum on page 17 of WB5RVZ's instructions says to use 221 Ohm resisters for 202, 204 and 205 then a...
I posted a picture in album W6ARH of Rocky on Windows 7 system with a USB SB XF-I with nothing attached. The center spike oscillates in amplitude and I cannot...
Hi All- Using and trying to QSO with... Rocky 3.6, USB synth, RxTx 6.3 on 9v DC supply. When I do the I/Q tx balance, I can get deep nulls OK. When I transmit...
