Hey Alex I have had a blast with the 3.6. Put me on the beta builder list if you need more. I have plenty of building experience and technical ability to...
Hi All, I have finished pricing for the UHF-SDR beta version kits. These are no frills kits, in order to have them ship more promptly. These are beta kits,...
Art
KY1K@...
Jul 1, 2009 7:49 am
34496
Hi All and Art From Thailand, I can't access to the site wb6dhw.com more than 3 days. Yes, also http://wb6dhw. com/Under_ Development. html on today. If other...
I wanted to try putting a Lite 2.0 on 10M. Besides reworking the front end, I figured I needed a 37.666MHz xtal or osc to center it on 28.250. I could find no...
... Hello Dohn, This is another day, so another opportunity to learn something. HI! Do you know that DB9 connectors don't exist? In fact it is a misuse of...
... From: "wa1edj" Subject: [softrock40] Softrock Lite 2.0 on 10M?? ... A crystal and the Si570 have low phase noise, therefore they are going to be better. At...
Hi Tof, I'm wondering whether there might be governmentall/political censsorship due to events in your region? Here is some more information on the UHF SDR...
Art
KY1K@...
Jul 1, 2009 4:50 pm
34506
... I had trouble myself a couple of days ago. I have Wildblue satellite and had to set my network connection to their automatic proxy configuration. I think...
Alan, I would consider using the Si570 as a stand alone osc. source but am a bit confused as to how to program it to startup on 37.666MHz. From following the...
... From: "Robert Confrey Subject: RE: [softrock40] Softrock Lite 2.0 on 10M?? Alan, I would consider using the Si570 as a stand alone osc. source but am a bit...
Thanks!...Just what I was looking for...The Kees kit looks great....73...Bob...EDJ... ________________________________ From: softrock40@yahoogroups.com...
G'day all, I tested the TX Mixer last night and found the 5V regulator getting hot. Could smell it too. This is what I did: connected a jumper lead between the...
Hi ALL  I am very thank to all reply. I use IE6 on WindowsXP and automatic setting detect configed. Today ,I can see web page via free proxy website. Art...
grant  my 5v reg runs a tad hot also, FWIW. i slipped an extra, slightly large nut on the other side of the board.  thought about dropping b+ to 6 or 7...
i have a nasty ground loop with my emu1212; since it HAS balanced line inputs, i put a couple of cheapie radio shack isolation transformers (p/n 271-1374) in,...
was i dreaming, or did i see a version of pSDR that had both panadpter and waterfall displays running simultaneously?? i like them BOTH!!! 73, w5xz, dan...
Greetings: I am new to SoftRock SDR and just recently received my version 9 kits from Tony. I sure am impressed with the packaging of the kits and the quality...
... I have some measurements on my bpf page at <http://www.wb6dhw.com/BPF.html>. My bpf board has 6 filters and 2 open positions. The loss measurements on...
I want to use the subject receiver to drive a panadaptor and the IF frequency is 13 MHz. It's not clear whether I need or can use one of the existing band...
One of the plug-in BPF is for 30m/20m/17m operation. This BPF will span you 13 MHz IF application. The Electronically Switched BPF spans 1.8 MHz through 30...
thanks, jack  i have looked at your site. great work. guess i overlooked this, though.  so, quick easy answer is "No great advantage with the triad over...
Dan: I believe the 10K is correct. The output impedance of the Softrock is near zero. After all, it is an op amp in a feedback circuit so it tries to maintain...
Dan, Jack is the master. Lot of worse ways to waste time than camping out on his page for some review... I had an instance where the ground loop was causing a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
