Hi Don, With the v2.0 firmware, band pass filter switching will NOT work with Rocky, you will have to wait and see if a new version is created to support it. ...
Hi all, As a follow up to the previous messages, here is some additional information that might be of use. I have had the opportunity and pleasure to try out...
Hi Bob & group, Thanks bob for the explanation, only a small remarks. ... Band Pass Filter (ABPF) option The ABPF option is by default enabled in the firmware...
... Users of RxTx v6.x wishing to do Tx/Rx switching (ie PTT), CW key lines, smooth tune and ABPF (eg. using the 9V1AL motherboard for both Rx and Tx BPF...
Hi Guys, Just downloaded the latest version released yesterday from Winrad.org website. Tested it with a SoftRock v9.0 receiver using Fred PE0FKO v15.9 ...
OK Bob, So who did this new version? that resolution meets my requirements as I use in RADIO Computers a screen 1024x768. Thank you for fast answer. 73 ... -- ...
Hi Jose, Looks like all future Winrad development is posted here: http://www.winrad.org/ 73, Bob G8VOI ... screen ... Winrad.org ... within the ... works ... ...
Update on the power numbers after adding a LPF to the EB63: Power output with 1W (20V pp) input is 63W (160V pp). Measured after the LPF at the dummy load. The...
Hi to all in the group Does anybody know of simple or novel methods of generating a pseudo PSK31 signals for use in SDR experimentation work. 73 steve_ g7was...
A lot of the digi mode software will allow you to record files of activity for playback. Couldn't you route the audio playback for testing? Or record I/Q wav...
When tuning across the band in PowerSDR SR-40 I notice how the display jumps from frequency segment to segment. Do the following lines in PowerSDR SR-40 file...
Hello Cesco, Is this driving the EB63 with a S/R or another source? If you have the test equipment, I'd like to know how the linearity looks when a S/R is...
Hello Bruce, ... An elecraft K2 (the qrp version) with a 3db attenuator. ... I dont have the equipment necessary. The pep rating of the eb63 is 200W, so lots...
Please take the current draw measurements with a large grain of salt. I should have been much more attentive to my results but, instead, I just blindly noted...
I just finished building through the dividers today. The power supply current with no series resistor was 4.4 ma's, local oscillator was 14.1 ma's. That was a...
We all appreciate all your info and all the hard work that's went into the info you provide. Everyone makes a mistake once in a while. I know I do! Keep up to...
Turned the V9 back on, and again, its taking commands from the hostware test app, but powerSDR or Rocky is not changing the frequency. This is really...
Alex, Art: Thanks for the Motherboard Kit. It arrived on Friday and I just finished assembly and test QSO with N9DSJ a few minutes ago. Works great! See...
Hi Javier, Congratulations!!! You are the 1st builder to complete the assembly and test of the mobo v3.6 (production kit) - well done :-) I am still half way...
... If you would like to build one, I have a circuit (8Meg jpg) I just scanned from RadCom April 1989 ... works fine. You may be able to find a source for a...
Hi Michael, I guess you must have the USB driver loaded correctly if the Test application is working, also assume you have either the original v1.4 or later...
Michael, Just had another thought, with the test program do you get all the correct answers as expected? Maybe the USB interface is working ok, but the problem...
... From: "g8voip" ... correct answers as expected And have you used USB_Synth? This will set the Si570 independently of the SDR programs but can be used at ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
