Been testing this SW with a XTALL 1.1 and Xtall version 1. In both version the SW works but very far away from the center frequencies. sometimes more than 1MHZ...
... From: "Jose Bonanca" ... In both version the SW works but very far away from the center frequencies. sometimes more than 1MHZ away. Jose, I expect you have...
Alan, Sorry I still donīt get a programmer but coming to have one. I am checking QRGīs in an HP counter. and it is correct with versions before 2.4 . I...
... frequencies. ... else is ... Hello Jose. Do you see the approx 56.3MHz (or other default freq), when the power is first applied? I just finished building...
Yes Terry I see the correct starting freq. but then the programmed freqs are off by - 1MHz. I do not think it is soldering problem. I may think in the...
Finished my kit yesterday. Did all the prelim tests in the Builders notes up to testing the receiver part. Everything checked out. Went to hook it to the...
Hi Hank, There is a series diode on the RXTX board to guart against the reverse power supply polarity problem so you should be ok. When the power supply is...
... one ... power ... good ... 570, ... The 12F683 was the problem with mine, wrong freq's. Erased and re- loaded the chip - problem solved - worked perfectly...
Please let me know if others are experiencing problems with the v2.4 frequencies in the PICs I have been sending out the the v8.3 kits mailed since May 26. ...
Jim, at least some one else with wrong freq,. I am going to receive a serial pic programmer by late thist week. Now I need to have the file of Tomīs v.2.4 to...
Hi Tony Could have been a handeling fault on my end, Everyone should observe the ESD practices (me too). Even the soldering iron can cause problems if it does...
Thanks Tony. 73 ... -- Jose Bonanca (CT1aos) Thanks Tony. 73 On Sun, Jun 1, 2008 at 6:43 PM, Tony Parks < raparks@... > wrote: Hi Jose, Tom's v2.4 HEX...
Hi Jose The file Tony pointed you to is the one I used. Loaded two chips with that HEX file and both work exactly as they are intended. Also tried the others...
Thank you JIM I got the file already. cheers ... -- Jose Bonanca (CT1aos) Thank you JIM I got the file already. cheers On Sun, Jun 1, 2008 at 6:59 PM, James R....
... From: "James R. Elledge" ... that HEX file and both work exactly as they are intended. Also tried the others Tom has provided and the work perfectly. Yes,...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the softrock40 group. File : /*W7QJQ,...
softrock40@yahoogroup...
Jun 1, 2008 7:28 pm
21928
I have posted two Si570-related files (in the *W7QJQ folder). One is a program to read and display (on an acsii terminal) the factory-programmmed Start-Up...
The DC voltage at pins 1 and 7 are correct. So the voltage regulator circuit looks good. I was able to borrow a scope and checked U7. No joy on the clock...
I had the same experience as KB2XJ with a mid may 8.3 kit. I verified the pic against the hex dump in the files area and found the program code matched but not...
Hi Dave, Please let me know the date you received your v8.3 kit. I am trying to determine if PIC's programmed with my new programmer contained the wrong EE...
... reverse power supply polarity problem so you should be ok. When the power supply is connected with the right polarity, what current is supplied to the...
Greetings! Received the kit, thanks Tony. I checked the PIC using the earlier XTALL board as installed on my RXTX, all frequencies are well within measurement...
Thanks Bob. That is after my new programmer went into use. Hopefully the PICs mailed last week were all in good shape. Thanks and 73, Tony KB9YIG ... From:...
Dave it means that you may had the same problem as me. Did you measured the deviation ? when did you receive your kit ? Was it after May 26? Thanks 73 ... -- ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
