Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the smartsockets group. File :...
9
whoop@...
whoop_john
Sep 23, 2006 10:06 am
I have uploaded a Filemaker Pro UDC segment editor to the files section. This creates the necessary user-defined character definitions for insertion into...
10
Chris
fixitsan2
Sep 23, 2006 11:18 pm
... starting ... offset ... send ... Thanks John, I've just got my free time back now my car restoration project is complete.....Just tonight i have begun...
11
Chris
fixitsan2
Sep 24, 2006 12:15 am
The UDC's are now available from character 32 to 127. I will look into setting the upper limit higher. in theory it should work, but those characters above 127...
12
Chris
fixitsan2
Sep 24, 2006 6:24 pm
I've set the lower UDC limit to location 0, the maximum is location 125 The system needs 3 bytes of space which are located at 253,254 and 255. Each UDC takes...
14
tigre2xxx
Oct 1, 2006 5:19 am
I would like to get a couple if they are available. Thank you, Jeffry...
15
fixitsan@...
fixitsan2
Oct 2, 2006 12:03 am
Hello Jeffry, sorry for the delay in responding to your email. Yes I have a couple of sockets already built and ready to go. Because they already have the...
16
smartsockets@yahoogro...
Oct 5, 2006 9:41 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the smartsockets group. File :...
17
tigre2xxx
Oct 20, 2006 4:54 pm
Hi Chris, The package you sent arrived the other day and I've just now had time to open it. There are a few extra parts included that you will need to instruct...
18
fixitsan@...
fixitsan2
Oct 20, 2006 6:16 pm
Hi, nice to hear from you again ! Well the best starting point would the smartsocket group files section. If you check the connections for the 5 pin connector...
19
Ken Wolfe
kenwolfe1
Dec 6, 2006 9:22 pm
Hello Chris, Do you have a few sockets left to sell? I'm looking for 6 if they are available. Thanks, Ken Wolfe...
20
Chris
fixitsan2
Dec 6, 2006 10:36 pm
... Hi Ken I have only unpopulated PCB's I should get in some microcontrollers too. I wish I had the time to build up more sockets but you are welcome to the...
21
Chris
fixitsan2
Dec 12, 2006 10:31 pm
A bugfix this time, and some clarification of the documentation. Files 'SmartV2' are the most recent files and are the only versions of useable code in the...
22
Ken Wolfe
kenwolfe1
Jan 7, 2007 5:32 pm
... Hello Chris, I've finally started to assemble the boards you shipped to me last month. I have a question about the pin sockets. Which pin sockets are...
23
Quixotic Nixotic
whoop_john
Jan 7, 2007 8:48 pm
... Ken, I used receptacles from D sockets, the kind where you get a strip of them separately. I just snipped the cable crimp bit off and bent the remaining...
24
Chris
fixitsan2
Jan 7, 2007 9:35 pm
...Happy new year by the way, good luck with it ! Ken, the receptacles are from Rapid Electronics, part number 22-1125 They're made by Harwin and can be veiwed...
25
Quixotic Nixotic
whoop_john
Jan 7, 2007 10:03 pm
... Yes Chris, I am mentioning it because of that discussion. That is why I didn't redefine those two chrs as they are off limits because they have special...
26
Ken Wolfe
kenwolfe1
Jan 8, 2007 12:12 am
... Thanks John, I might try that. Ken...
27
Ken Wolfe
kenwolfe1
Jan 8, 2007 12:29 am
Chris,John, I found those Harwin pins at Mouser so I won't get smacked for overseas shipping. Mouser number: 855-H3161-01 Harwin number: H3161-01 ...
28
Quixotic Nixotic
whoop_john
Jan 8, 2007 12:47 am
... Ken, Chris's boards are heaps of fun and mine worked straight out of the box without a hitch. I think they are a good way of showing off what are rare and...
29
Chris
fixitsan2
Jan 8, 2007 9:06 am
... available ... first. ... That's good Ken, I was concerned that I had specified using a part made of unobtanium. I think I only have 4 boards left, and...
30
Ken Wolfe
kenwolfe1
Jan 25, 2007 2:40 am
Chris, I finally started to populate the boards tonight (yay!) I have one question. What value is R-31? I looked through what paperwork I have and haven't...
31
fixitsan@...
fixitsan2
Jan 25, 2007 9:49 am
Hello Ken, that's good news ! R31 is the anode resistor and is optional. It's optional in the sense that if you use a 170Vdc power supply then you only need to...
32
Ken Wolfe
kenwolfe1
Jan 26, 2007 7:05 am
Thanks Chris It makes sense now. ;) Ken ... sense that ... pads with a ... about...
33
gopstein
Mar 11, 2007 3:35 am
Do you already have boards for the ZM-1350? They seem to be easier to get than the B7971....
34
Chris
fixitsan2
Mar 11, 2007 1:02 pm
... Hello there, No , I haven't attempted to make any special boards just for the ZM1350. Althogh I do know of at least one member of this group who has used...
... I'm guessing that more and more people will use the ZM1350 because of the cost and availability of the 7971's. I could give a layout a try, but I've never...
37
Quixotic Nixotic
whoop_john
Mar 11, 2007 8:46 pm
... I would also like a set of these. I can do a pcb layout if you are too busy, Chris. That's a bummer about Zetalink. Ray is a nice guy, but he's in a hole ...
38
Chris
fixitsan2
Mar 11, 2007 9:32 pm
... because of ... try, ... going ... layout... ... you'd be ... hole ... Hi John, For me the biggest hurdlle isn't to do the layout but to make an accurate...
