I have a 797 that is one year old and I have never done a software update on it yet. What am I missing? I see some thing called SI enhance on some of the...
The attached photo to the previous email is exactly the problem I am having.. except I have probably 50-100 ov them from St Louis all the way to northern...
Hi, I turned the 997 unit on today on the water after 4 months of perfect SI displaying and found out that there is no SI image view / reading, just 2 narrow...
Two narrow lines on left and right sounds like it's interpreting a down-beam sonar input. Have you tried connecting the SI transducer directly to the unit,...
No, I did not try bypassing the switch , I do not know whether there is enough cable left from switch to reach main unit. I will check it. But I checked that...
I know this may be an old subject but I just bought a 997 and I have seen so many config's of mounting the si transducer I am confused. I have herd mounting it...
my friend just bought 997csi. I'm helping him install unit, he has a ranger 519vx, the motor doesn't have a jackplate installed like the pictures on the site....
Hi everyone, I'm new to this group and I have a new 997c SI. Is the only way to update software on my unit via SD card or is there a cable for USB on my PC to...
I have the standard transom mount transducer that came with my new 798cSI, and it works beatifully as advertised. The only question I have is related the...
Can anyone verifiy if these two brands will interfere with one another? My hope is with the Lowrance using 20 degree cone at 200 kHz and setting the HB to use...
THe 200 kHz is still powered even if you switch it to 83 khz. There are noise filters that you can adjust on the HB to reduce interference. Maybe someone that...
Replace the upper pin in the bracket with a bolt like the images in the photo albums of the Skeeter install. this is how they do it at the factroy and I do...
Call HB Customer Service they can take care of you. Doug  ... transducer that came with my new ... beatifully as advertised. The only question I have ... the...
 http://www.dougvahrenberg.com/Humminbird.html Click on the Humminbird How To Guide on the top LEft it will tell you how to do it. Doug ... my PC. ... I. ... ...
My veiw with noise is to isolate which it sounds like you have done. You might try a different way of routeing your power cord for the unit. ... From:...
Yes you have to up load off home computor on SD card and up load card onto the unit. I havnt done it yet but I have only owned mine one day. Good luck ... ...
Sir I run a Lowrance side by side with my Humminbird 997si and I get just a little interference.Nothing though that I still can't see my sideimaging fairly...
Here is my question, really don't know how to ask it. With the interlink, if your running with two GPS pucks(one front by the TM and other in rear right over...
Hi, I have a 797 SI with a in hull transducer and SI transducer mounted to the jacking plate linked through a TW switch box. Problem I have is that when I...
Here's my $0.02 guess: It doesn't look like you can mount the Si transducer on the transom to the outside of where the tie down straps go as it looks like this...
I suggest that you update your unit. Si Enhanced is a collection of a few menus that will allow you to further adjust the Si sonar images on your unit. This...
I would also try testing your unit on someone else's boat that has an Si unit as well. Greg Walters at Humminbird ________________________________ From:...
Eric, You must select the receiver you want to use with each unit. (there is a menu) .It is importnt because the default selection is interlink. Therefore if...
Got any pictures of his boat that you can post? Will need pictures of the transom area both from behind and from the sides at the level that the transducer...
You can update your 997 unit using the communications cable from the PCConnect Kit but it was designed for the smaller less power hungry units as it uses a two...
Isolating or eliminating the source of the interference would be nice but that is not always possible with RF interference. What we do is provide a kit that...
As Blackie stated: when the GPS Receiver Override menu in the "Auto" setting it will automatically select the GPS receiver that your InterLinked unit will use...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
