Boy! I sure do like to ask questions here,cause you never have to worry about getting an answer. I thank everybody who has sent me a reply to my question.Every...
Actually, the list so far has been about which machines we think look good. It's important to remember that, if you're going to restore the machine to like-new...
Hi,I wish someone would explain to me the difference in polarized and non-polarized capacitors. Considering the size of them, the construction seems the same....
.I think the place you are looking for is "Atlas Plating" http://www.atlaschrome.com/ They plate both metal and plastic. I never had jukebox parts done, but...
Hi! I just took the mechanism out of my juke so I could put in my replacement. I thought it would be smart to check it over, so I could fix it and keep it as a...
lytics which are like small batteries only charge one way. when connected back-wards they over-current and explode much like making a mistake with the jumper...
The flourescent light in the top panel of my SQS 160 began flickering and then the center section went dead. The ends of the tube still glow, but the center...
Hi All, I'm a newbie to Seeburg jukeboxes (i have 2 NSM machines) and I was wondering where I could purchase around 30 replacement chaser lamps to suit a...
For those tiny bulbs I purchased them from WWW.Mouser.com . There are a couple of other sources for these bulbs. The bulb number should be in your manual. For...
Which contacts are you referring to? If you mean the Tormat Read-Out contacts (the spring-loaded pins that ride below the Tormat contact 'rivets' and send the...
Thank you for your reply selectomatic I am referring to almost every contact located on the front of the mechanism. They are burned and some hardly have any...
Hello, Member for 3-4 months- first post. I have the "bug" for the 50's Seeburgs, and own the following models: Seeburgs 100 BL, 100 G, 100 R, VL-200, KD-200,...
Thanks for the info. I actually switched the starter on the top panel w/ a starter on a vertical bulb on the bottom panel so see if the problem switched. To...
... They're type 2182 grain-of-wheat bulbs. As to replacement tips for the Entertainer - have patience, lots of patience and a steady hand. Cheers, Tony...
If these contacts are the copper leaf kind with a round contact at the end then you cannot use any type of grease or lube on them. One reason these can burn is...
Fluorescant lamps can be the damndest things to fix. Over the years I have had many experiences where I replaced everything (or so I thought), and had to...
one of the vexing contact problems is a loose connection where the contact "point" is riveted in to the leaf. I have usually solved these by soldering the...
in many areas cap values are not critical and slightly larger [say up to 25% larger] will work fine. most main filter, decoupling, & bypass are areas where it...
A guy from Moline contacted me, and asked me about fixing his HSC-1. Unfortunately, I'm not much on traveling, so I won't be able to go look at it. These...
I am retired. i did an HSC 6001 for the experience and sold it thereafter. I don't need any more experience in this area. while I am happy to pass on to others...
in IL I just the Jukebox works http://www.jukeboxworks.com/ George is a solid tech and makes house calls. He has looked at all 6 of my jukeboxes at one...
Went on a free parts raid at a buddys picked up two SHP3 amps two digital control centers a set of black/gray boxes an extra pair of horns two keyboard...
... Always happy to hear someone got something I designed working. Although I take no credit (nor blame) for the lamps themselves. Cheers, Tony Miller...
here a tube manual and an FET front end volt meter will help. each tube can be checked for correct bias and current draw. weak tubes, open cathode resistors,...
I was under this impression also until I tried substituting polarized caps for diodes in a bridge configuration for rectification. They ran cool until a load...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
